2017 Ford F-150

Defect. Ford Motor Company (Ford) is recalling certain 2017 F-150 vehicles previously repaired incorrectly under recall number 17V053. The instrument cluster may lose power after initial vehicle start-up in cold ambient temperatures. Several gauges, including the transmission gear position indicator, may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect."

Risk. An instrument cluster that fails to display critical safety information, such as gear position or warning lights, increases the risk of a crash or injury.

Remedy. Dealers will update the Instrument Panel Cluster Assembly (IPC) software, free of charge. Owner notification letters were mailed July 17, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C26. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6, 2026.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2017 F-150 vehicles. A loss of signal between the transmission range sensor and the powertrain control module can cause the transmission to unexpectedly downshift into second gear.

Risk. Unexpectedly downshifting into second gear may result in a loss of vehicle control, increasing the risk of a crash.

Remedy. Dealers will update the powertrain control module software, free of charge. Owner notification letters were mailed July 24, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S28. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026.

Defect. Ford Motor Company (Ford) is recalling certain 2017-2018 F-150, Expedition, and Lincoln Navigator vehicles. The brake master cylinder may allow brake fluid to leak from the front wheel circuit into the brake booster.

Risk. A brake fluid leak can cause reduced brake function and extend the distance required to stop, increasing the risk of a crash.

Remedy. Dealers will replace the brake master cylinder. If the master cylinder is leaking, the brake booster will also be replaced. Repairs will be performed free of charge. Owner notification letters were mailed September 25, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S37. This recall is an expansion of NHTSA recall number 22V-150.

Defect. Ford Motor Company (Ford) is recalling certain 2016-2017 Ford Expedition, Lincoln Navigator, and 2016-2018 F-150 vehicles equipped with 3.5L Ecoboost engines. The brake master cylinder may allow brake fluid to leak from the front wheel circuit into the brake booster.

Risk. A loss of brake fluid may result in a change in brake pedal travel, increased pedal effort and reduced front brake function, requiring greater effort and distance to stop the vehicle. These conditions can increase the risk of a crash.

Remedy. Dealers will replace the brake master cylinder. If the master cylinder is leaking, the brake booster will also be replaced. Repairs will be performed free of charge. An interim owner notification letter notifying customers of the safety defect were mailed on April 29, 2022. Owner notification letters were mailed April 29, 2022. This recall is an expansion of NHTSA recall number 20V-332. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S11.

Defect. Tenneco Automotive (DRiV) is recalling certain MOOG K500359 ball joints, for aftermarket installation on 2015-2018 Ford F-150 trucks. The ball joint may have a misaligned dust boot and may be missing alignment hole and installation warning tag, which may lead to improper alignment of the ball joint.

Risk. An incorrectly installed ball joint may cause the ball joint stud to break, which can compromise front wheel control, increasing the risk of a crash.

Remedy. DRiV will notify owners, and dealers will inspect, and if necessary replace the ball joint, free of charge. Owner letters were mailed May 5, 2021. Owners may contact Tenneco Automotive customer service at 1-877-489-6659.

Defect. Ford Motor Company (Ford) is recalling certain 2014-2017 F-150 pickup trucks equipped with 3.5L Ecoboost engines. The brake master cylinder may leak brake fluid into the brake booster.

Risk. A loss of brake fluid may result in a change in brake pedal travel and feel, increased pedal effort and reduced front brake function, possibly requiring greater effort and distance to stop the vehicle. These conditions can increase the risk of a crash.

Remedy. Ford will notify owners, and dealers will replace the brake master cylinder and inspect the brake booster, replacing it as necessary, free of charge. Ford issued owners an interim notification on June 30, 2020. The recall began on October 28, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S31.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2019 Ford F-150 and 2017-2019 Ford F-250 Super Duty, F-350 Super Duty, F-450 Super Duty, and F-550 Super Duty pick-up trucks equipped with an engine block heater and previously remedied under recall 18V894. During the previous repair, the block heater cable's splice connector may have been damaged.

Risk. A damaged cable could cause a resistive short, increasing the risk of overheated or melted wiring, increasing the risk of a fire.

Remedy. Ford will notify owners, and dealers will disable the engine block heater from being used. When replacement cables become available, a second notice will be mailed and dealers will replace the engine block heater cord, free of charge. The recall began May 31, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S11.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2019 Ford F-150 and 2017-2019 Ford F-250 Super Duty, F-350 Super Duty, F-450 Super Duty, and F-550 Super Duty pick-up trucks equipped with an engine block heater. Water and contaminants may get into the block heater cable's splice connector causing corrosion and damage.

Risk. When the heater is plugged in, prolonged corrosion could cause a resistive short, increasing the risk of overheated or melted wiring which can increase the risk of a fire.

Remedy. Ford will notify owners, and dealers will disable the block heater cable, free of charge. Once parts are available, Dealers will replace the engine block heater cable, free of charge. The recall began June 3, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S45.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2018 Ford F-150 Regular Cab and SuperCrew Cab vehicles. If a front seat belt pretensioner deploys as the result of a crash, the sparks may ignite materials such as carpeting or insulation within the B-pillar area.

Risk. A vehicle fire could result if materials ignite inside the vehicle.

Remedy. Ford will notify owners, and dealers will remove the B-pillar insulation material and wiring harness tape, and install heat resistant tape, free of charge. The recall began September 28, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S27.

Defect. Ford Motor Company (Ford) is recalling certain 2017-2018 Ford F-150 and 2018 Ford Expedition and Mustang and Lincoln Navigator vehicles equipped with 10-speed automatic transmissions. A roll pin may not have been installed in the transmission, potentially causing a loss of the "Park" function.

Risk. Despite the transmission shift lever being placed in 'Park' and the instrument panel display indicating 'Park,' the vehicle may roll away after it has been exited if the parking brake has not been applied, increasing the risk of injury or a crash.

Remedy. Ford will notify owners, and dealers will inspect the transmission to make sure it has the roll pin, installing one if it is missing, free of charge. The recall began on April 13, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S09.

Defect. Ford Motor Company (Ford) is recalling certain 2017 F-150 vehicles equipped with ten-speed transmissions. The pin that attaches the transmission shift linkage to the transmission may come out, preventing the transmission from responding to movement of the shift lever.

Risk. The disconnected linkage may cause the vehicle to not move forward or backward as selected by the driver with the shift lever. Additionally, despite selecting 'Park', if the parking brake is not applied, the vehicle may roll. Either scenario increases the risk of a crash.

Remedy. Ford will notify owners, and dealers will replace the roll pin with an updated part, free of charge. The recall is expected to begin December 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S36.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2017 Ford F-150, and 2017 F-250, F-350, F-450, and F-550 Super Duty trucks. The doors on these vehicles may have a bent or kinked actuation cable or the door latches may freeze after water gets into the latch. Either condition can result in the doors opening while driving although they appear to be closed.

Risk. A door that opens while driving can increase the risk of injury.

Remedy. Ford will notify owners, and dealers will inspect the door latch actuation cables and repair if necessary, and install water shields over the door latches, free of charge. The recall began October 12, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S33.

Defect. Ford Motor Company (Ford) is recalling certain 2017 Ford F-150, F-250, F-350, F-450, and F-550 trucks with manually-adjusted front passenger seats. The seat belt anchor may not be adequately welded to the seat cushion frame. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages," and 207, "Seating Systems."

Risk. The seat belt buckle weld may fail, preventing the occupants from being properly restrained in the event of a crash, increasing the risk of injury.

Remedy. Ford will notify owners, and dealers will replace the front passenger manual seat track, free of charge. The recall is expected to begin November 6, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C17.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2017 F-150, and 2017 F-250 and F-350 trucks equipped with a crew cab. The left rear inflatable seat belt buckle assembly may be inadequately attached to its mounting bracket. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages."

Risk. If the left rear inflatable seat belt buckle separates from it's mounting bracket, the seat occupant may not be adequately restrained, increasing their risk of injury.

Remedy. Ford will notify owners, and dealers will inspect the seat belt assembly, replacing the attaching rivet as necessary, free of charge. Interim notices informing owners of the safety risk were mailed October 18, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 17C12.

Defect. Ford Motor Company (Ford) is recalling certain 2017 F-150 and Mustang vehicles. The air bag inflator within the passenger frontal air bag module may rupture in the event of a crash.

Risk. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy. Ford will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began October 11, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S26.

Defect. Ford Motor Company (Ford) is recalling certain 2017 Ford Explorer, F-150, F-250, F-350, F-450 and F-550 vehicles equipped with a manual driver's seat back recliner mechanism. In the event of a crash, the seat back frame may not restrain the occupant due to having inadequate welds. As such, these vehicles may not meet the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 202a, "Head Restraints" and 207, "Seating Systems."

Risk. If the occupant is not adequately restrained in the event of a crash, they have an increased risk of injury.

Remedy. Ford will notify owners, and dealers will inspect and, if necessary, replace the seat back frame, free of charge. The recall began on June 7, 2017. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 17C08.

Defect. Ford Motor Company (Ford) is recalling certain 2015-2017 F-150, and 2017 F-250, F-350, F-450, and F-550 vehicles originally produced with black or body colored exterior door handles that may have been subsequently equipped with a chrome exterior door handle cover accessory kit purchased from a Ford dealer. These accessory door handle covers may cause the doors to unlatch in a side impact collision. As such, these vehicles may fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."

Risk. If the doors unlatch and open in a side impact collision, the occupants have an increased risk of injury.

Remedy. Ford will notify owners, and dealers will remove the accessory covers and refund the purchase price. The recall began July 13, 2017. Owners may contact Ford at 1-866-436-7332. Ford's number for the recall is 17C09.

Defect. Ford Motor Company (Ford) is recalling certain 2017 F-150 trucks equipped with an eight-inch productivity screen. In these vehicles, the instrument cluster may lose power after the initial vehicle start-up in cold ambient temperatures. Several gauges, including the transmission gear position indicator, may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicles Safety Standard (FMVSS) number 102, "Transmission shift position sequence, starter interlock, and transmission braking effect."

Risk. If the transmission gear position indicator fails to illuminate, the driver may be unable to tell the transmission shift position, increasing the risk of a crash or injury from unintended vehicle movement.

Remedy. Ford will notify owners, and dealers will reprogram the instrument cluster, free of charge. The recall began February 20, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C01.

On March 21, 2025, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE25002) to investigate instances of unexpected transmission downshifting without driver input in model year (MY) 2015-2017 Ford F-150 vehicles (subject vehicles) manufactured by Ford Motor Company (Ford). The complaints allege that, without warning or driver input, the subject vehicles experienced a sudden and rapid deceleration often accompanied by temporary rear wheel lockup, seizure, or skidding, resulting in a loss of vehicle control that increases the risk of crash and injury to all …

On March 21, 2025, NHTSA’s Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE25002) to investigate instances of unexpected transmission downshifting without driver input in model year (MY) 2015-2017 Ford F-150 vehicles (subject vehicles) manufactured by Ford Motor Company (Ford). The complaints allege that, without warning or driver input, the subject vehicles experienced a sudden and rapid deceleration often accompanied by temporary rear wheel lockup, seizure, or skidding, resulting in a loss of vehicle control that increases the risk of crash and injury to all …

On June 18, 2018, the Office of Defects Investigations (ODI) opened a Preliminary Evaluation (PE18-008) to investigate complaints alleging post-crash fires at the B pillar in the area of the seat belt pretensioners on MY 2014-2018 Ford F-150 Regular Cab, and Super Crew Cab Vehicles. On August 24, 2018, Ford Motor Company recalled (FSA 18S27 - NHTSA #18V568) the affected population. Ford's investigation found that some front seat belt pretensioners may generate sparks during deployment in excess of Ford's specification. Sparks in the pretensioner exhaust gases inside the lower portion of the …

Customer Satisfaction Program 26N04 Certain 2015-2017 Model Year F-150 Vehicles Equipped with a 6R80 Transmission Transmission Molded Leadframe Replacement

Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation

Certain 2015-2020 Model Year F-150 Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening REASON FOR THIS SUPPLEMENT Parts ordering information and full repair instructions are now available to support completion of this customer satisfaction program.

Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement; Owner letters are scheduled to mail during the week of September 27, 2021 Submitting Claims with Ford Protect for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA with …

For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details …

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this …

This bulletin supersedes TSB 25-2301. Reason for update: update the Part List Description. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) …

Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for …

This article supersedes TSB 24-2046 to update the Service Procedure LTIS statement. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) …

Transmission range and output sensors failed inside the molded leadframe, triggering P0720 and P0722. Ford program 26N04 denied coverage because the codes were not on the approved list. The violent downshifting in my truck has made it undriveable and I am unable to go to work and I am being treated horribly.

The contact owns a 2017 Ford F-150. The contact stated that while driving at 55 MPH, the check engine warning light illuminated, and the transmission unexpectedly downshifted. The dealer was contacted and made aware of the failure. The vehicle was taken to the dealer, where DTC: P0715 was retrieved. The contact was informed that the recall repair could not be completed without additional fault codes. The contact was advised to contact the NHTSA Hotline to report the failure. The contact stated that the failure was persistent. The contact received notification of NHTSA Campaign Number: 26V237000 (Power Train); however, the part to do the recall repair was unavailable. The manufacturer was contacted and made aware of the failure. The failure mileage was approximately 59,060.

My 2017 Ford F-150 with SYNC 3 (software version 3.0, build 23219, the latest version Ford offers for this vehicle) has a recurring defect with hands-free phone calls. When a call comes in while my phone ([XXX]) is connected through Android Auto, the call displays as connected but there is no audio in either direction — I cannot hear the caller and the caller cannot hear me. Outgoing calls work normally. Ford's published workaround for this known defect is a setting ("Use Phone Ringtone"), but on my vehicle the setting will not stay selected — it reverts to the default every time the phone disconnects or the vehicle is shut off, so the failure returns on every trip. Ford fixed this defect in its newer SYNC 3.4 software, but has never made 3.4 available for 2017 vehicles, leaving no remedy. The truck is already on the final 3.0 build. This is a safety issue. Washington law prohibits holding a phone while driving, so a failed hands-free call pressures the driver to pick up and handle the phone. The vehicle's [XXX] Assist emergency feature also depends on SYNC maintaining a working phone connection, which this defect defeats. The failure has occurred repeatedly since I got the truck last year and is ongoing INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2017 Ford F-150. The contact received notification of NHTSA Campaign Number: 25V236000 (Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The dealer was contacted several times and informed the contact that the parts were on backorder. Due to the safety risk, the vehicle was taken to an independent mechanic, where the brake master cylinder was replaced at the owner's expense. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the repair and informed the contact that reimbursement was denied because parts were available.

The contact owns a 2017 Ford F-150. The contact stated that while driving at 65 MPH, the transmission unexpectedly downshifted to a lower gear, and the vehicle slowed down abruptly. Additionally, the wrench warning light was illuminated. The contact associated the failure with NHTSA Campaign Number: 26V237000 (Power Train); however, the part to do the recall repair was not yet available. The local dealer was contacted and made aware of the failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 85,000.

Transmission shutters while shifting gears, makes me worry about possibly crashing.

Hello. I recently went in for fords recall regarding 2015-2017 6R80 Transmissions and their limp mode and sudden downshift issues. I got the recall done July 31st (if memory serves) But the fix did not work. I came back in September 3rd to complain and ask them to diagnose and asked if they would fix it this time under the same recall. After 3 hours of waiting they said that my code “P0722-00” does not qualify for lead frame replacement nor did they attempt another fix. I believe this is entirely unprofessional and borderline dangerous. Not everyone can afford a 1200$ repair, especially not for something that should’ve been fixed under the recall. I’ve heard of other potential reports just like this one and wanted to make our voices known. This took place at the Ford dealership in Eden NC. (Tri city ford) But there is one major thing I’d like to add. The staff was extremely professional and welcoming and explained everything thoroughly, just simply nothing they could do at this level. I do not want anyone to be fired or anything like that. I simply want my truck to be safe to drive again, since they claim it can suddenly downshift and break the wheels lose. It is my only car.

My 2017 Ford F-150 is experiencing serious transmission issues that appear to be related to Safety Recall 26S28. The vehicle is shifting harshly, failing to shift properly, shifting only into 3rd and 5th gears, sometimes failing to engage 6th gear, and occasionally losing all power. A generic wrench warning appears on the dash with the message “See Service Manual.” A code reader also displays diagnostic trouble code P0722. I took my vehicle to Great Lakes Ford of Muskegon, where the dealership diagnosed the issue and confirmed that the lead frame needs to be replaced. The lead frame is the component addressed by this recall. However, the dealership stated that because the vehicle was not displaying a specific required code, they could not perform the repair under the recall. My vehicle is currently not drivable and is clearly exhibiting serious symptoms consistent with the issue addressed by the recall. Despite this, I have been told that I must pay approximately $1,500 out of pocket to repair a component that I believe should be covered under Ford’s recall. This issue presents a significant safety hazard. When the problem first occurred, I was making a left turn when my truck suddenly lost all power. I was nearly struck by oncoming traffic because I could not accelerate to complete the turn safely. Given the unpredictable shifting, loss of power, and other transmission issues described above, I do not believe this vehicle is safe to operate. My truck is currently at the deal

Vehicle failed Pennsylvania state safety inspection due to structural rust holes and perforation in the high-strength steel frame rails. The vehicle has only 40,000 miles and has been safely operated, indicating premature structural metallurgy failure."

The contact owns a 2017 Ford F-150. The contact stated that while driving at 65 MPH, the vehicle unexpectedly downshifted, and the power shift indicator area began flashing. The contact stated that due to the failure, the rear wheels unexpectedly locked up. The contact received notification of NHTSA Campaign Number: 26V237000 (Power Train); however, the part to complete the recall repair was not yet available. The vehicle was taken to the dealer. The dealer confirmed that the parts were not yet available and advised the contact to park the vehicle until the remedy became available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure and referred the contact to the dealer for assistance. The failure mileage was approximately 90,000.

SUPPLEMENTAL DEFECT REPORT ATTACHMENT Original NHTSA Complaint ID: [Case#11770807]/[Case #11772091] Vehicle suffered an identical uncommanded rear-wheel lockup and immediate drop to a low gear at highway speeds in October 2025. Kendall Ford replaced a Gateway Module rather than the transmission molded leadframe. The vehicle is now displaying active codes P0715 and P0717, which Ford Corporate is using to deny coverage under Recall 26S28. Ford is actively excluding P0715/P0717 input sensor codes from the recall, despite the component being physically identical and resulting in the exact same violent highway lockup hazard.

My vehicle is experiencing the exact severe safety risk detailed in NHTSA Recall 26V237 (Ford Campaign 26S28) - dropping gears and risking a crash. The dealer technician confirmed the lead frame has physically failed but is denying the remedy due to a technicality over ancillary speed sensor codes embedded in that very part Molded Lead Frame.

Months ago, experienced loss of power, deacceleration and a grinding noise as it downshifted by itself. I ran an ODB-II on it and got 4 codes. Had it towed to dealership and was told it was the manifold arm and paid over $4,200 to replace it. Now, it'd happening again- with the same 4 codes and according to FORD whom I just talked to, states that this is the Powertrain molded lead frame issue. It is a known issue(recall 26S28/26V237) and that is has no remedy. The current value is over $13,000 but it's been sitting at the dealership where I had to have it towed. With no end in sight. What are we supposed to do with a non-operative vehicle? How can ford just say, "Sorry- there's nothing we can do." And the issue have been know for years. Where is the proof they are actively searching for a remedy??

This complaint is regarding the failure and inadequacy of the safety remedy for Ford Safety Recall 26S28 (NHTSA Campaign Number 24V237000) on my 2017 Ford F-150. My vehicle was brought to an authorized Ford dealership one month ago to satisfy Recall 26S28 due to an intermittent loss of the transmission output speed sensor signal (DTC P0722), which causes sudden, unexpected downshifts on the highway. The dealership performed the mandated PCM software update but refused to replace the physically failing molded leadframe hardware. The safety recall remedy has failed. The physical component has degraded further, and the vehicle is once again dropping the transmission speed sensor signal (Code P0722) while in motion, forcing the truck into limp mode on active roadways. Ford Motor Company corporate customer service and their authorized dealer network are actively refusing to replace the physical molded leadframe, (Case Ref: CXH09624298), claiming the recall only mandates a software flash for this specific code. By refusing to replace the physically failing internal transmission hardware, Ford is leaving an unsafe vehicle on the road. The software patch is an inadequate safety remedy that does not prevent the underlying electronic components from failing while driving at highway speeds.

The contact owns a 2017 Ford F-150. The contact stated that while accelerating at 70 MPH, the vehicle experienced a sudden loss of motive power followed by transmission gear hunting and hesitation, causing the transmission to improperly downshift. Additionally, the wrench warning light illuminated. The contact associated the failure with a recall notification received for NHTSA Campaign Number: 26V237000 (Power Train). The dealer was contacted; however, the parts to complete the recall repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall remedy. The manufacturer was notified of the failure by phone. The failure mileage was approximately 120,000.

On 10/13/2026, driving about 25 mph on a city street, my truck entered failsafe with no prior warning lamps or symptoms. The PCM cut most engine power, leaving no acceleration, and set P1285 (CHT Overtemp Sensed) and P1299 (CHT Overtemp Protection Active). The engine was not overheating; a $40 CHT sensor fixed it. Evidence: I watched live data on an Autel MaxiCheck MX808S-TS while driving during the events. CHT dropped to implausibly low values for brief moments, then immediately returned to normal values matching coolant temp. Coolant temp stayed normal throughout. Failsafe triggered on these momentary dropouts, never on an actual high reading. The PCM logic is unsafe: 1. A low-reading sensor dropout was reported as an overtemp. The PCM set two overtemp codes and no sensor circuit code. 2. It ignored contradicting data. CHT recovered instantly and matched normal coolant temp, yet the PCM acted on one momentary bad reading. 3. The response was disproportionate. A sensor glitch with normal coolant temp should set a check engine light and circuit code, not remove engine power while driving. 4. It creates a crash risk. Losing acceleration in city traffic, amid chimes and flashing warnings, left me unable to keep pace or maneuver and caused anxiety and distraction. 5. False overtemp codes mislead owners. A typical owner would likely need a tow and a costly cooling system diagnosis over a $40 sensor glitch. Even as a former mechanic, I spent hours chasing a nonexistent cooling pro

My vehicle is experiencing the exact severe safety risk detailed in NHTSA Recall 26V237 (Ford Campaign 26S28) - dropping gears and risking a crash. The dealer technician confirmed the lead frame has physically failed but is denying the remedy due to a technicality over ancillary speed sensor codes embedded in that very part.

During light deceleration or light acceleration in the 10 speed gear ranges of 3 to 5, my transmission gives a sudden CLUNK noise and jerk. I have about 85K miles of light in town and highway use. The last date of occurrence is documented in additional details.

I am reporting a potential safety defect involving the hood latch sensor or electrical system on my 2017 Ford F-150, currently at 151,895 miles. On three occasions (10/3/26, 10/4/26, and 10/7/26), the "Hood Ajar" warning appeared while driving, accompanied by an audible chime, although the hood appeared securely closed. The message remains displayed until I press OK on the steering wheel. 10/3/26: The warning activated while driving. I safely pulled over, released the hood latch, inspected the hood, and closed it again. The hood had appeared properly secured. 10/4/26: The warning activated while I was descending a steep hill with no shoulder or safe place to stop. Concerned the hood could open and obstruct my windshield, I had to continue driving until reaching the bottom of the hill and finding a turnoff. Upon inspection, the hood was completely closed. 10/7/26: The warning activated again. Because the previous two inspections showed the hood was closed, I dismissed the warning without stopping. This demonstrates how repeated false warnings can cause drivers to disregard a potentially legitimate safety alert. The security alarm also intermittently activates while parked, sounding the horn and flashing the lights without an apparent cause. These malfunctions create safety concerns, including driver distraction, potentially dangerous roadside stops, and the risk that drivers may ignore a legitimate warning about an unsecured hood. My experience descending a steep hill without

Phil long ford motor city Colorado Springs worked on my truck July for injector 6 and other oil gaskets on [XXX] the fuel rail o rings fails on that side and leaks gas from Santa Fe New Mexico to Chalmers ford Rio rancho to seek diagnostic for fuel leak today is October 7 2026 and Phil long ford is denying responsibility and pretending not enough information the truck is fixed but not covered by the ford warranty INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Sudden downshifts too 1st gear and 3rd gear from highway speeds. Also goes into limp mode. The codes needed to replace the molded lead frame are present, was at the dealer yesterday and Ford will not let them make the needed repairs under warranty. Ford said I must wait an undetermined amount of time for them too try and find a fix for this before anything else can be done. Besides this being the only vehicle I have at the time too drive, it is totally UNSAFE to drive. Ford needs to come up with a fix now or replace the molded lead frame now so repairs will be complete and I will have a safe vehicle to drive. This problem is happening almost everytime I drive. It started on 9/26/26 and continues today.

The contact owns a 2017 Ford F-150. The contact received notification of NHTSA Campaign Number: 25V236000 (Service Brakes, Hydraulic). The local dealer was contacted and informed the contact that parts for the recall repair was on back order. The manufacturer was contacted and referred the contact to other dealers for assistance.

My 2017 Ford F150 has been downshifting unexpectedly now for weeks. There have been a few times when I literally lost control of my truck. I am afraid to drive on Highway. I use my truck for work and everything else. The local Ford dealership here Astro Ford in D'Iberville, Ms told me yesterday they will not repair my truck based on guidance from Ford...they recieved just a few days ago....saying the recall repair is inadequate and another remedy is being worked on. I cannot drive my truck to go to work to make money to pay bills. Based on what I have read they will also refuse to give me a car loaner of some kind for the time being. What XXX am I supposed to do now??????

It shifts down randomly and throws code P0720.Stays in 6th gear and will not allow normal acceleration could potentially be dangerous. Ford stated this isn't covered under the lead frame replacement recall. The speed sensor is part of that lead frame.

My Transmission will townshift suddenly on the Highway. The error code I get is the (P0720) output-speed-sensor. I have noticed it has been recalled before. It is very scary when I am driving, and I know it has to be hurting my engine and transmission. I got a recall notice and thought it was for this, but it was for other error codes similar to this. According to my research they all seem to very closely associated. I took it to the dealership, and they said ford won't cover my issue.

The contact owns a 2017 Ford F-150. The contact stated that while driving at various speeds, the transmission unexpectedly downshifted from 6th gear to 2nd gear. The vehicle was taken to the dealer, where the torque converter was replaced; however, the failure persisted. The contact received notification of NHTSA Campaign Number: 26V237000 (Power Train); however, the part to do the recall repair was not yet available. The dealer was contacted and informed the contact that the recall repair appointment could not be scheduled because the manufacturer had placed a hold on the recall on September 28, 2026. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 80,000.

2017 F-150 is dropping into limp mode due to code P0722 (OSS sensor), but Ford's safety recall 26S28 framework fails to replace the broken hardware for this specific code. Dealership performed PCM Update recall campaign 26S28/26V237. Charged me for a diagnostic fee because P0722 is not covered in the customer satisfaction program campaign 26N04, Even though P0722 points to the same transmission molded leadframe failure. After the PCM update my truck will still drop into limp mode and can be dangerous if pulling onto highway and stuck in 3rd gear causing no power during taking off. It also will sometimes stay in 1st gear and I have to pull over and shut the truck off to get it to shift again.

Driving on interstate when my truck suddenly flashed a wrench light and downshifted to 5th gear. Truck went into limp mode limiting my gears to 3rd through 5th gear. Had vehicle towed to Ford Dealership. They wanted $399 just to do a diagnostic and scan for codes. My truck was showing code P0720 (Output Shaft Speed Sensor) at my house before being towed. This output shaft speed sensor is integrated into the internal molded lead frame, which is the part that was recalled for replacement on Safety Recall Notice 26S28/NHTSA Recall 26V237. However, Ford will not cover this under the lead frame recall. My guess would be because they know it’s a loophole and they can still make money off of repairs for the same part.

My transmission has been slipping. To the point where it has made me stop, especially on hills and in cold. 10 Spd auto. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2017 Ford F-150. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 26V237000 (Power Train); however, the failure occurred after the recall repair. The contact stated that while driving at an undisclosed speed, the transmission started slipping. The dealer was made aware of the failure and informed the contact that a diagnostic test was needed to determine the cause of the failure. The failure mileage was approximately 93,000.

After a big freeze my fuel level gauge stopped working. I have replaced every sensor and fuse possible, along with multiple new fuel pumps. It has been taken to a certified Ford Dealership and they can’t find the problem. There is a Ford recall that already explains the problem exactly. It is Ford 26C26. I am not able to get my vehicle inspected and without knowing exactly what my fuel level is it could leave me stranded.

The contact owns a 2017 Ford F-150. The contact stated that the air bag warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed and determined that the clock spring needed to be replaced. The contact associated the failure with NHTSA Campaign Number: 23V847000 (Steering, Air Bags); however, the contact was informed that the VIN was not included in the recall. The manufacturer was notified of the failure by phone, but no assistance was provided. The contact was referred to the NHTSA Hotline and to the DMV for assistance.

The torque converter has malfunctioned and the vehicle is currently at the dealership for repairs. The truck experiences significant vibration and shuddering at speeds above 45 mph. There is an existing recall for this exact issue; however, our VIN is not included in the affected vehicle population. With only 60,000 to 70,000 miles on the truck and less than 10 years of service, a major component such as the torque converter should not require replacement, especially on a vehicle that has been properly maintained throughout its life.

The contact owns a 2017 Ford F-150. The contact stated that while driving 60 MPH, the contact attempted to stop the vehicle, but the vehicle failed to stop as needed and the braking distance became extended. Additionally, the brake pedal was firm while depressed. The contact received notification of NHTSA Campaign Number: 25V236000 (Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted by phone and was made aware of the failure.

My vehicle's transmission changed gears suddenly and unexpectedly causing a slight difficulty to control. Following the sudden gear change, some lights on the dashboard began flickering erratically. I have video of the dashboard after the gear change. For this incident, I was driving about 25 MPH. I experienced similar behavior before and at highway speeds. Since then, the vehicle was serviced by Ford for a Safety Recall Notice 26S28/NHTSA Recall 26V237. The service performed under the recall did not fix the problem. The local Ford dealer told me they would charge me to have the problem investigated, so I have not brought the vehicle in to them.

My 2017 Ford F-150 V8 with the 6-speed automatic transmission has been experiencing a serious and recurring transmission malfunction. The truck has consistently, almost on a daily basis, gone into limp mode and become stuck in 5th gear. It also frequently fails to downshift to 1st gear when coming to a stop. Instead, it remains in 3rd gear, requiring the truck to pull away from a complete stop in 3rd gear. The dealership did perform the software update on 08/20/2026 ,yet the issues remain the same. The vehicle has set diagnostic trouble code P0722 for the transmission output speed sensor. I have been informed that the output speed sensor is molded into the transmission lead frame and cannot be replaced separately, requiring replacement of the lead frame. Today, the transmission malfunction created an immediate and potentially life-threatening safety situation. As I pulled out of my driveway, the truck remained in 1st gear and would not properly progress through the gears. It then abruptly jumped into 2nd gear and caused the vehicle to stall/lose forward progress while I was entering the roadway. Oncoming traffic was nearly upon me and I was almost struck. The vehicle eventually engaged the proper gear and continued moving, but by that time I was in a dangerous, life-threatening situation. This is not an isolated incident or an occasional inconvenience. The transmission has been repeatedly malfunctioning, including going into limp mode in 5th gear and failing to downshift appr

In 2025 my 2017 Ford F-150 started randomly downshifting. We took the car to the ford dealer who could not assess what the problem was exactly (Rowe Ford in Westbrook, Maine). They suggested a new transmission to be safe and clearly indicated that this was not a safe truck to drive at the time. We took the truck to another ford dealer to try to get an actual determination of what was wrong (Casco Bay Ford, Maine). They also advised that no codes were being given but that the truck was clearly downshifting and not safe. With no real alternatives or clear problem, we paid $8,000+ for a new transmission. Then, months later we get the recall notice: (Campaign 26S28 / NHTSA Recall 26V237) - Ford F-150's were downshifting... We had Ford do the software update as this is now a new transmission, but when we asked about the Recall and if there was anything we could do about the $8,000 we just paid lower and upper management (we talked to both) advised that because they could not definitively put a label to the problem before we fixed the transmission that they could not attribute the downshifting to the same problem and so will not help or otherwise reimburse us for the cost of having to fix the problem that was recalled later. No remedy was offered by Ford.

The vehicle has a ten speed transmission. It started with the transmission making minor down shifts from 3 to 1 and then 7 to 1. Without any engine warning light. It has subsequently started a severe shift from 3 to 1 and 7 to 1 and the engine light has now come on. This creates a dangerous situation when it down shifts from 7-1 when your speed is 45 mph of above. I contacted a dealership regarding a repair but was told there is no recall and it would cost $215 to diagnose and from $4,500 - $8,000 for the repair. It is a known issue to the Ford dealers but without a recall they are gouging the consumers who is at risk of accident.

The contact owns a 2017 Ford F-150. The contact stated that while driving 15 MPH, the brake pedal was depressed; however, the brakes became inoperable. The brake pedal was depressed and went to the floorboard, and the vehicle was driven in LIMP Mode back to the residence. The dealer was contacted by phone and associated the failure with NHTSA Campaign Number: 25V236000 (Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted by phone and was made aware of the failure. The failure mileage was approximately 146,118.

The 4-5-6 drum ring in my transmission went out on my truck that has 70, 318 miles on it. Vehicle was missing shift points and would not always shift properly causing power to not be available when expected - especially dangerous when trying to merge onto a highway. Vehicle was inspected by a Ford dealership and by ABC transmissions of Tacoma WA. I paid ABC Transmissions $9,693.98 to fix the problem. The transmissions would clunk badly and was very obviously missing shift points. They first appeared 30k miles ago but Ford lied to me saying it was a "software problem".

I am filing this complaint because a Ford-authorized dealership, West Hills Ford in Bremerton, Washington, returned my vehicle to me in an unsafe condition after performing a repair under federal safety recall 25S37 (NHTSA Campaign 25V-236, brake master cylinder), and because an independent inspection has since documented physical evidence of a real defect connected to that repair. Please see attached documents outlining this entire incident as well as supporting documentation.

Odometer Fraud. The contact purchased a 2017 Ford F-150. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of the purchase, the vehicle mileage was approximately 170,000, and it was later discovered via a third party that the mileage was 250,000.

Vehicle is subject to active Safety Recall 26S28 for transmission lead frame and range sensor failure causing unexpected downshifts into 1st gear. Vehicle experienced downshifting symptoms creating severe road hazard and risk of rear-wheel lockup. Dealership cleared diagnostic trouble codes without saving freeze-frame logs, mis-entered VIN on billing estimates, and refused to complete the recall repair. Vehicle is available for inspection.

On XXX, my [XXX] son was driving this 2017 Ford F-150 when the transmission suddenly downshifted while traveling on the road. The downshift was severe enough that the rear tires lost traction and the vehicle fishtailed, nearly resulting in an accident. The vehicle was taken to an authorized Ford dealer on 8/18/2026. We reported the sudden downshift, but the dealer was unable to duplicate the condition. The dealer performed Ford Recall 26S28/NHTSA 26V-237 and campaign 19G01, and the vehicle was returned on XXX. On XXX, only two days after the recall repair, the engine unexpectedly shut off while the vehicle was being driven. It restarted afterward. On XXX, the engine again unexpectedly stalled while the vehicle was moving. When the engine stopped, power-steering assist was lost and the driver had to coast the vehicle safely to the side of the road. The engine restarted immediately. When attempting to drive away, the transmission appeared to be starting in approximately third gear rather than first gear. After the vehicle was moving, the transmission eventually began operating normally again. Ford Customer Relationship Center was notified on XXX and formally documented these incidents. The vehicle is available for inspection. I am concerned because the original sudden downshift closely resembles the safety defect addressed by Recall 26V-237/26S28, and serious intermittent stalling and abnormal transmission operation have continued after the recall remedy was performed. I am req

Driving back from tri cities and when we were on I5 the transmission abruptly shifted down and went to a very high RPM. Was able to limp off the freeway by UW, and then drove home slowly. Had it trailered by the dealership i had just bought it from and they brought it to a shop where they said the transmission needed replaced.

In late July 2026, my son received a Ford safety recall notice (Recall #26S28) for his 2017 F 150 requiring a PCM software update. I brought the truck to Crown Motors in Redding on August 11th for the recall service. Before this appointment, the truck had no performance issues. Immediately after picking up the truck, a noticeable pinging sound occurred under acceleration. I returned the vehicle on August 12th, where Crown Motors confirmed the issue and advised spark plug replacement. This did not resolve the problem. I was also told that continued driving could damage the engine, so the truck remained at the dealership. Over the following days, Crown Motors worked with Ford engineering and repeatedly attempted software-related fixes. Crown staff informed me they believed the recall update caused the issue, and the first internal Ford team reportedly agreed. However, on August 25th, Ford’s second internal review determined the software update was not responsible and stated that all repair costs would fall on me—despite the clear timeline showing the problem began immediately after the recall service. Customer Service provided no assistance and refused to escalate my concern. As a result, my truck is currently non-operational, Crown Motors does not have a fix, and Ford will not cover repairs triggered only after Ford’s own safety recall. According to NHTSA’s info, it seems Ford is obligated under Motor Vehicle Safety Act (49 U.S.C. § 30111 et seq.) to repair the vehicle. I am r

This lead frame issue is never ending. Well over a decade without a proper remedy. I’m very familiar with it. but this one nearly ended my life. After the near collision I called my mechanic and bought a new ford lead frame from a dealership. It’s doing fine now, it’s been 1 year. the incident caused my truck to go into park or possibly reverse at highway speed just as I passed a semi truck and returned to the right lane. If the trucker had not been paying attention it would have been bad. There was nothing I could do. . On top of this, he was under the impression that it was intentional. So I almost got into a physical altercation until I convinced him to look inside my truck as my gear indicator light was dancing from gear to gear while not touching anything.. To add to the seriousness, my taillamps never came on because I didn’t touch the brake. It was a horrible timing.. . Shortly after this i received a notice from Ford explaining the cause and symptoms of this issue, but then stated there was no fix at the time, but the vehicle was “safe to drive.” That is irresponsible. This was the only time mine did it, no prior issues. I got new ford parts and had it replaced. my mechanic said they deal with this weekly! Then I get a letter from Ford saying there is a fix and it’s a computer programming issue which is totally not true. That’s just a smoke screen, but it also goes on to say it could be a lead frame and if you’ve already fixed it before you got a letter, they will ref

Short in the rear window defroster. Within 5 minutes of turning off the defroster after only having it on for 2 minutes at 2:30am leaving work, the back window exploded outward and shattering. No rocks, no other folks on the road. Upon research, and after contacting insurance company and the glass repair company, this is a very common issue in 2015-2019 F-150s. But there are no safety recalls. Praise God my children were not in the backseat, they would have been riddled with glass. How is this not a safety issue?

Not sure if I can file an issue for this, but I wanted to let you know that a Ford Safety recall caused other issues after it was applied. In late July 2026, my son received a Ford safety recall notice (Recall #26S28) for his 2017 F 150 requiring a PCM software update. I brought the truck to Crown Motors in Redding on August 11th for the recall service. Before this appointment, the truck had no performance issues. Immediately after picking up the truck, a noticeable pinging sound occurred under acceleration. I returned the vehicle on August 12th, where Crown Motors confirmed the issue and advised spark plug replacement. This did not resolve the problem. I was also told that continued driving could damage the engine, so the truck remained at the dealership. Over the following days, Crown Motors worked with Ford engineering and repeatedly attempted software-related fixes. Crown staff informed me they believed the recall update caused the issue, and the first internal Ford team reportedly agreed. However, on August 25th, Ford’s second internal review determined the software update was not responsible and stated that all repair costs would fall on me—despite the clear timeline showing the problem began immediately after the recall service. Customer Service provided no assistance and refused to escalate my concern. As a result, my truck is currently non-operational, Crown Motors does not have a fix, and Ford will not cover repairs triggered only after Ford’s own safety recall. I b

I am filing a formal complaint regarding improper service practices, breach of safety recall protocols, and severe resulting vehicle damage committed by Fox Grand Traverse Ford. On April 23, 2026, independent facility Kinney’s Complete Auto Repair replaced the lead frame connector on my vehicle. During service, the transmission pan was dropped and inspected. The transmission was certified clean, free of metal shavings, and operating normally. On August 3, 2026, a mobile service technician from Fox Grand Traverse Ford performed Safety Recall 26S28 (PCM Software Update) at my workplace parking lot. Ford Motor Company’s official support guidelines explicitly state: "Ford Mobile Service is unavailable for Recall 26S28." Servicing requires in-dealership PCM reprogramming and post-flash adaptive calibration. Because the service was performed in a parking lot, the technician omitted the mandatory post-flash adaptive learning drive cycle. The vehicle immediately suffered harsh shifting, hydraulic pressure spikes, and forward rolling while in Reverse. Fox Ford now demands $7,883.73 for a complete transmission replacement, falsely claiming there metal shavings in the gear box and that the damage was a "pre-existing condition," despite the recent clean pan inspection from April 2026.