2014 Ford F-150

Defect. Ford Motor Company (Ford) is recalling certain model year 2014 F-150 vehicles previously repaired incorrectly under recall number 24V444. A loss of signal between the transmission output shaft speed sensor and the powertrain control module (PCM) can cause the transmission to unexpectedly downshift into first gear.

Risk. Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.

Remedy. Dealers will update the PCM software, free of charge. Owner notification letters were mailed July 8, 2026. Owners may contact customer service at 1-866-436-7332. Ford's number for this recall is 26S45. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6, 2026.

Defect. Ford Motor Company (Ford) is recalling certain 2014 F-150 vehicles. A loss of signal between the transmission output shaft speed sensor and the powertrain control module can cause the transmission to unexpectedly downshift into first gear, regardless of vehicle speed.

Risk. Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.

Remedy. Dealers will update the powertrain control module software, free of charge. Owner notification letters were mailed July 1, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S37.

Defect. Ford Motor Company (Ford) is recalling certain 2014-2017 F-150 pickup trucks equipped with 3.5L Ecoboost engines. The brake master cylinder may leak brake fluid into the brake booster.

Risk. A loss of brake fluid may result in a change in brake pedal travel and feel, increased pedal effort and reduced front brake function, possibly requiring greater effort and distance to stop the vehicle. These conditions can increase the risk of a crash.

Remedy. Ford will notify owners, and dealers will replace the brake master cylinder and inspect the brake booster, replacing it as necessary, free of charge. Ford issued owners an interim notification on June 30, 2020. The recall began on October 28, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S31.

Defect. Ford Motor Company (Ford) is recalling certain 2014 Ford F-150 and E-350, 2014-2015 Ford Escape, and 2015 Lincoln MKC vehicles. Improperly manufactured bolts may have been used to install certain seats, seatbacks, seatbelt buckles, or seatbelt anchors on these vehicles.

Risk. The improperly manufactured bolts may fracture. If a seat, seatback, or seatbelt anchor attaching bolt fractures, the affected component may not be properly secured, increasing the risk of injury in the event of a crash.

Remedy. Ford will notify owners, and dealers will replace the affected bolts, free of charge. Interim notices informing owners of the safety risk were mailed September 8, 2017. Owners will receive a second notice when remedy parts become available in the fourth quarter of 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S17.

Defect. Ford Motor Company (Ford) is recalling certain model year 2013-2014 F-150 vehicles manufactured August 1, 2013, to August 31, 2014 equipped with 3.5L engines. The master cylinder rear cup seal may roll, resulting in brake fluid leakage from the primary reservoir into the brake booster.

Risk. Loss of brake fluid from the primary reservoir results in a complete loss of front brake function, increasing the risk of a crash.

Remedy. Ford will notify owners, and dealers will replace the brake master cylinder and, if necessary, the brake booster, free of charge. The recall began on October 28, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S24.

Defect. Ford Motor Company (Ford) is recalling certain model year 2014 Ford F-150 and Flex vehicles manufactured March 1, 2014, to May 31, 2014. The affected vehicles were manufactured with a reduced clearance between the seat frame and the seat track assembly. This can cause the Occupant Classification System (OCS) to inaccurately register passenger weight and improperly suppress the passenger front airbag when the passenger seat is occupied by an adult passenger. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 208, "Occupant Crash Protection."

Risk. Improper suppression of the passenger airbag increases the risk of an injury to the seat occupant in the event of a crash necessitating deployment of the front passenger airbag.

Remedy. Ford will notify owners, and dealers will widen the gap between the seat frame and seat track assembly and recalibrate the seat OCS, free of charge. The recall began November 25, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14C10.

Defect. Ford Motor Company (Ford) is recalling certain model year 2014 F-150 vehicles manufactured March 1, 2014, to March 13, 2014. The affected vehicles may have a brake pedal position switch that is improperly adjusted. As a result, the brake lights may illuminate with a delay or not at all. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. If the brake lights fail to illuminate, or illuminate after a delay, there is an increased risk of a crash.

Remedy. Ford has notified owners, and dealers will adjust the brake pedal position switch, free of charge. The recall began on November 24, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14C09. Note: Until the vehicle has been remedied, owners are advised not to use their cruise control system.

Defect. Ford Motor Company (Ford) is recalling certain model year 2014 Ford F-150 trucks manufactured May 26, 2014 to June 19, 2014, and equipped with Electronic Power Assist Steering (EPAS). The affected vehicles may have an incorrectly installed EPAS gear motor position sensor magnet that can lead to a total loss of steering control while driving.

Risk. A loss of steering control while driving increases the risk of a vehicle crash.

Remedy. Ford will notify owners, and dealers will replace the EPAS steering gear, free of charge. The recall began in July 2014. Note: Owners are advised not to drive their vehicles until they have been remedied. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S09.

In September 2016, Ford Motor Company (Ford) issued safety recall 16V-248 which included certain model year (MY) 2011-2012 Ford F-150 vehicles equipped with 6-speed (6R80) automatic transmissions. This recall was in response to allegations of unintended, unexpected vehicle transmission downshifting to a lower gear without warning, often accompanied by temporary rear wheel lock-up, increasing the risk of a crash and/or injury, and included approximately 153,581 vehicles. Ford identified the root cause of the unintended, unexpected vehicle transmission downshifting to a lower gear to be …

On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in …

FORD 2014 F-150 W/3.7L: THIS TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. CUSTOMER SATISFACTION PROGRAM EFFECTIVE NOV.13,2015 FOR VEHICLE MODELS REGARDING THE ENGINE BLOCK REPLACEMENT. *LJ

Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram …

Some 2013-2018 F-150 vehicles equipped with electronic shift on-the-fly (ESOF) 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. ESOF can be identified as it does not have a 4WD AUTO (4A) position on the mode selector switch (MSS). This may be due to a loss of vacuum to …

Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with four wheel drive (4WD) may exhibit an intermittent grinding noise while driving in two wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the …

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the …

Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - …

2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING …

I am submitting this complaint on behalf of my stepfather regarding a safety incident involving a 2014 Ford F-150. After coming to a complete stop at a red traffic light while on a curve, the truck shut off completely and would not restart. The hazard lights continued to function. The truck was towed to our home and has remained there because it is not drivable. We discovered Ford Safety Recall 24S37, NHTSA campaign number 24V444, which concerns a potential failure of the transmission output speed sensor (OSS). This failure may cause an unintended downshift into first gear, potentially resulting in rear-tire sliding and loss of vehicle control. The recall remedy involves updating the powertrain control module (PCM) software and checking for diagnostic trouble codes. We do not believe this recall repair has been completed, but this has not yet been confirmed. Although the shutdown does not exactly match the condition described in the recall, we are concerned about a potential safety-related defect and request that this incident be documented and investigated to determine whether it may be related to the recalled condition or another vehicle defect. A repair invoice dated March 13 also documents work that appears to involve cutting and programming a vehicle key. We request that this repair history be considered when investigating the cause of the shutdown. We request that the vehicle's recall status and repair history be verified and that the cause of the shutdown be investigat

In the last month this has happened twice. While driving down the freeway my vehicle just downshifted on its own, speedometer dropped to 0, and I lost steering power but vehicle was still running. The wrench for service came on and the battery light also. As I was trying to get to a safe location the infotainment system went off first followed by my dash lighting. On the first time it happened after letting the vehicle sit for about an hour upon restart everything reset and was ok, but the engine light is still on after second incident and I'm afraid to drive it now.

I own a 2014 Ford F-150 equipped with the 6R80 six-speed automatic transmission (VIN: [XXX]), currently at approximately 133,000 miles. On XXX, while driving at ~70 mph on [XXX], my truck experienced an abrupt, unintended downshift — the precise failure mode described in Recall 24S37. The software patch prevented it from making it worse and a orange wrench came across the dashboard, but still it required some evasive maneuvering. I proceeded directly to the dealer to investigate; however, they were booked for the day. Not understanding the full impact I left to come back in the morning. The vehicle eventually became unsafe to operate, would not start, and had to be towed to Gullo Ford. The dealer then pulled diagnostic trouble codes, confirmed the transmission lead frame had failed, and replaced the lead frame at my expense of $1,977.04 (2127.04 with a coupon of 10% off) (invoice and repairs completed enclosed). INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My truck has had repeated transmission issues, and has been "addressed" by two separate recalls (24S37 and 26S45). However, I am still having issues. I believe that "24S37 Supplement #1" specifically covers the issues I am having, yet Ford still continues to disregard my request. Tis is a major safety issue. It is my son's truck, and I am driving it now since I don't want anything to happen to him.

During a panic stop the brakes failed and the pedal went to the floor resulting in a rear end collision. The vehicle is currently with the mechanic but he believes it a failed brake booster. When I checked for related problems it seems the same brake booster (EL3Z-2140-E) in my 2014 F150 V8 5.0L was used in the same year 3.5L but yet the recalls (16S24 and 20S31) didn't include my vehicle

Brake master cylinder failed, leaking all Brake fluid into the Brake booster. I find recalls for this year model, but not my truck.

I was driving up the Interstate I565 heading towards Decatur Al from Huntsville Al. I was cruising at about 80 mph. All of a sudden my trucks transmission downshifted into first gear causing my back end to fish tail and the RPM's maxed out in the red and the engine lost all power. After that it would not start and I had it towed to the Ford Dealership. They did nothing and they charged me. They went ahead and took care of the recall then: because an intermittent loss of signal from the output shaft speed (OSS) sensor / internal lead frame can cause an unexpected downshift to first gear regardless of vehicle speed. Recall DetailsPrimary/Initial Recall: Campaign 24S37 (NHTSA 24V444) in June/July 2024, covering over 550,000 U.S. vehicles (approx. 668,000 globally).Follow-up / Re-repair Recall: Campaign 26S45 (NHTSA 26V378) issued mid-2026 for roughly 44,963 vehicles where the prior PCM software fix was improperly applied or missed.Affected Vehicles: Select 2014 Ford F-150 trucks built at Dearborn and Kansas City plants (built mid-2013 through late 2014) What Happens & Safety RiskSymptom: Sudden, unintended drop to first gear, potentially causing rear-wheel lock-up, skidding, or a sudden reduction in vehicle speed.

The contact owns a 2014 Ford F-150. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 24V444000 (Power Train); however, a failure occurred after the recall repair. The contact stated that while driving 40 MPH, the transmission unexpectedly downshifted into first gear. The transmission warning light was illuminated. The contact stopped, turned off, and restarted the vehicle. The vehicle resumed normal operation. The vehicle was taken to O'Reilly Auto Parts, and DTC: P0722 (Output Speed Sensor Circuit No Signal) was retrieved. The vehicle was then taken to the dealer, and the molded leadframe was replaced. The manufacturer was notified of the failure by phone. The failure mileage was approximately 145,500.

Keeps going into limp mode, codes are pointing to lead frame, a lot of sensor A codes. Rough shifting from 1st to 2nd as well as sudden down shiffting.

Ford did recall on transmission, it failed on my way home. I took it back and they refuse to fix trying to separate event to warranty issue. 3weeks later I have no truck and being stalled by ford. Even Elena Ford has it on her desk(computer) 4 days no response. They quickly processed the recall so they can imply it never had one. Lead module(connector) is reason and part of recall.

Suddenly lost power steering dash lights for traction control and power steering assist it takes a lot of strength to steer it no prior warning and I recently had spinal surgery

Odometer Fraud. The contact purchased a 2014 Ford F-150. It was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 154,279. The contact stated that the mileage listed on the paperwork was 153,945.

While accelerating to pass another vehicle, on numerous occasions, and at speeds of 45-65 MPH, transmission suddenly downshifts to first gear, and engine over revs, followed by a very loud slam in the drivetrain. This has happened about twenty times, once with my wife along. There is a recall on 2014, F-150’s, but my VIN was not included. The dealership is refusing to investigate because they haven’t been able to reproduce this intermittent problem. I, essentially, have been told to pick up the vehicle that I’m afraid to drive. Must I wait until I have an accident because the rear wheels lock up?

The contact owns a 2014 Ford F-150. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the brake pedal was depressed to the floorboard but failed to respond as intended. The contact enabled the parking brake to stop the vehicle. The vehicle had experienced catastrophic brake failure. The vehicle was taken to the dealer, where it was diagnosed with a leak in the brake master cylinder. The contact was informed that the brake master cylinder, brake booster, and brake vacuum sensor needed to be replaced. The vehicle was not repaired. The manufacturer was contacted by phone, and a case was filed. The failure mileage was approximately 106,000.

The contact owns a 2014 Ford F-150. The contact stated that while driving, the transmission became stuck in fifth gear. The “WRENCH” warning light was illuminated at start-up. The contact stated that while shifting from neutral(N) to reverse(R), the vehicle made a clunking sound and lurched backward. The failure became progressively worse. While driving at various speeds, the transmission unexpectedly downshifted to first gear. A dealer was notified of the failure. The contact associated the failure with NHTSA Campaign Number: 26V237000 (Power Train); however, the VIN was not included in the recall. The failure mileage was approximately 171,000.

We purchased this 2014 Ford F-150 SuperCrew (3.5L EcoBoost) used on Dec 31, 2022. Just two days after taking it home, the vehicle began experiencing sudden, violent, uncommanded downshifts from 6th to 1st gear at highway speeds. This occurred throughout our ownership. Because this was our family's only form of transportation, we had no choice but to continue driving it under these terrifying conditions, repeatedly navigating a lethal safety hazard with our three children in the vehicle until the powertrain suffered a catastrophic failure. This matches the exact defect investigated under NHTSA Campaign 24V444 / Recall 24S37 and expanded under Recall 26S45. On Dec 23, 2023, a final highway downshift forced the powertrain into 1st gear, creating immense kinetic stress and engine-braking that instantly shattered internal components and caused a severe engine knock. Less than a mile later, while trying to get our family home in life-threatening -40 degree Fairbanks winter weather with our three children inside, the engine completely blew, leaving us stranded. The Fairbanks Ford dealership initially stated that Ford would be liable for the consequential damages. However, it later backtracked, claiming that a local customer satisfaction program had "timed out" at the 150,000-mile threshold. A diagnostic certification from a local Nissan dealership has documented the failure. I was an original reporter aiding the push to reopen this failed software recall investigation, and Ford's co

The contact's mother owns a 2014 Ford F-150. The contact stated that while his wife was driving 65 MPH, the brake fluid warning light illuminated. The brake pedal was depressed and went to the floorboard. The vehicle failed to stop. The contact's wife engaged the parking brake, and the vehicle was able to slow down, and the vehicle was pulled over and parked in a parking lot. The manufacturer was made aware of the failure and informed the contact that the vehicle was previously repaired under NHTSA Campaign Number: 16V345000 (Service Brakes, Hydraulic), and that the warranty had expired. The failure mileage was approximately 119,000.

I have a 2014 F150 manufactured in 5/2026 and recently had my electronic power assist steering fail. Ford issued recall 14S09 / NHTSA 14V-316. The recall was for F150's made between 5/26/2014 and 6/19/2026 that covered a steering gear motor position sensor magnet that was installed incorrectly. The result of this problem was a failure of the electronic power assist steering. Ford just diagnosed my F150 with an internal binding/failure of the steering gear, but when I searched for the recall using my VIN it wasn't included in the recall. I find this more than coincidental that my truck was manufactured in May of 2014 and just had the same failure stated in the recall.

The contact owns a 2014 Ford F-150. The contact stated that while driving 50 MPH, the RPM increased with the transmission stuck in second gear. There was an abnormal sound coming from the transmission. The vehicle was pulled over, the ignition was turned off, and the vehicle was restarted, and the vehicle operated as intended. No warning light was illuminated. The vehicle was taken to the dealer to be diagnosed, and the contact was provided an estimate for the diagnostic test. The vehicle was then taken to an independent mechanic to be diagnosed, and the contact was informed that the output shaft speed sensor and the valve body needed to be replaced. The vehicle was not repaired. The vehicle was serviced under the NHTSA Campaign Number: 24V444000 (POWER TRAIN) by the owner of the vehicle, but the remedy failed to prevent the failure. The contact stated that the failure had occurred after receiving the recall repair. The manufacturer was notified of the failure and informed the contact that, since the recall was already performed, the additional repair would be an out-of-pocket expense. The failure mileage was 160,000.

After transmission had programming update it never shifted properly. Took it to the dealer for diagnostic and they said nothing wrong. Transmission failed at only 82000 miles.

My 2014 Ford F-150 was previously included in Ford Safety Recall 24S37 regarding unintended transmission downshifts caused by an intermittent Output Shaft Speed (OSS) sensor issue. The vehicle was inspected by a Ford mobile technician on January 20, 2026. No qualifying codes were found at that time, and the recall was closed under my VIN. The recall involved the risk of an unintended downshift into first gear that could result in loss of vehicle control. On August 20, 2026, while my husband was driving approximately 40-50 mph, the truck suddenly downshifted and rapidly lost speed. The vehicle would not accelerate beyond approximately 10-15 mph and had to be moved into a parking lot to avoid remaining in traffic. After parking, the truck would no longer move under its own power. The wrench warning light illuminated and the vehicle became undrivable. The symptoms experienced appear substantially similar to those described in Recall 24S37. The dealership has indicated that the current failure may involve the transmission lead frame and speed sensor system, but I am concerned that this event may be related to the same transmission downshift condition addressed by the recall. I am requesting that NHTSA document and review this incident.

On July 30, 2026, while operating my 2014 F-150 under normal driving conditions, the dash cluster information screen displayed a "Brake Fluid Level Low" warning. Moments later, the brake system experienced a sudden/catastrophic loss of front braking performance. The brake pedal became severely spongy and traveled completely to the floorboard, requiring drastically increased distance to bring the vehicle to a stop. Due to ineffective braking, I missed the driveway of the parking lot I chose to inspect/determine what the issue was and subsequently could not stop the truck within the confines of the parking space. This brake failure put me, my family as well as oncoming traffic and pedestrians in jeopardy of injury or death due to collision. A mechanical inspection of the vehicle revealed the rear cup seal inside the brake master cylinder had failed. This internal seal failure allowed hydraulic brake fluid to bypass the cylinder and leak directly into the vacuum brake booster, completely contaminating the booster assembly. Without effective braking, the truck was deemed too dangerous to drive so it was parked and unused until replacement parts could be installed. This specific component failure, internal seal degradation, and resultant fluid contamination of the booster is identical to the safety defect detailed in NHTSA Campaign #16V345000 (Ford Recall #16S24). However, this specific vehicle was excluded from that safety campaign solely because it is equipped with the 6.2L V8 e

The contact owns a 2014 Ford F-150. The contact stated that while driving at an undisclosed speed, the wrench warning light illuminated, and the transmission unexpectedly downshifted to third gear. Additionally, the vehicle immediately went into LIMP Mode and failed to accelerate as needed. The contact associated the failure with NHTSA Campaign Number: 24V444000 (Power Train); however, the VIN was not included. The dealer was contacted and diagnosed the vehicle with molded leadframe failure. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was unknown.

The contact owns a 2014 Ford F-150. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 26V378000 (Power Train); however, the failure occurred after the recall repair was performed. The contact stated that while driving at an undisclosed speed, the transmission unexpectedly downshifted with the check engine warning light illuminated. The vehicle was taken to an independent mechanic, where a diagnostic trouble code for the transmission was retrieved. The vehicle then failed to restart and was towed to the dealer. The dealer determined that the molded lead frame needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 127,000.

While driving, the malfunction indicator light (yellow wrench) will illuminate, followed by a complete loss of communication between the instrument cluster and the transmission. The speedometer immediately drops to zero even though the truck is still moving, and other information, such as the fuel range, goes blank. The truck will also struggle to accelerate from a stop, almost as if it is starting in second gear. If I shut the truck off and restart it, everything returns to normal. Before the malfunction light comes on, the transmission will often make a very hard downshift or remain stuck in first gear and refuse to shift as speed increases. After a few seconds, the warning light appears, communication is lost, and the transmission shifts again, often very harshly. This seems to happen more often at lower speeds. This creates a serious safety risk because I lose all knowledge of my speed while driving, and the transmission may not respond properly when pulling into traffic or trying to reach a safe place to pull over. The dealer is aware of the problem. Recall 24S37 was supposed to correct it, but it did not. Recall 26S45 acknowledges that the original repair was not effective for all vehicles, but my VIN is not included even though I am experiencing the same failure. I have reported the issue to the dealer multiple times by phone and through their online service system. A dealership representative told me I am not the only customer experiencing this problem, but the dealer

The vehicle experienced an uncommanded, severe downshift from 5th gear directly into 1st gear while traveling at approximately 45 mph on a public road. This caused sudden, violent engine braking and an immediate drop in speed, creating an extreme rear-end collision hazard and potential loss of vehicle control. This vehicle previously received the PCM software update under Ford Safety Recall 24S37 (NHTSA Campaign 24V444). The software update failed to prevent the sudden downshift event caused by the failing Output Shaft Speed (OSS) sensor on the transmission molded lead frame. When contacting Ford Corporate Customer Service and local dealerships, Ford refused to cover diagnostic scanning or hardware replacement, claiming the recall is marked "completed" in their database because the software patch was installed more than 12 months ago. A software update that fails to prevent a 5th-to-1st downshift leaves a defective physical sensor on the road. Ford is refusing to evaluate or remedy a persistent, life-threatening recall failure on a 6R80 transmission.

While driving, brakes pushed to floor, and vehicle alarm beeped showing Low brake fluid sensor had tripped. Brakes not working properly, pedal goes to floor, brake fluid added to refill and fluid emptied out of master cylinder reservior two more times, vehicle inoperable to drive with no brake pressure. Open safety recalls for Ford F150 models 2013-2014 #16S24, and for F150 Models 2014-2017 #20S31, both specifically for the 3.5LV6 Ecoboost engine, which I have, but Ford is saying that mine is not covered for the same brake master cylinder / brake booster issue.

Vehicle Information: Year: 2014 Make: Ford Model: F-150 Component: Power Train (Transmission / Powertrain Control Module) Dealership Involved:Midway Motors Ford, 2075 E Kansas Ave, McPherson, KS 67460 Complaint Description:I am filing a formal safety complaint against Ford Motor Company and Midway Motors Ford in McPherson, KS, for failing to provide a free remedy under active federal safety recall 24S37 (NHTSA Campaign 24V444).My 2014 Ford F-150 was brought to the dealership to complete safety recall 24S37, which addresses severe, sudden transmission downshifts. The dealership performed a software update to the Powertrain Control Module (PCM). Immediately following this update, the truck's drivability severely deteriorated, and the transmission began violently slamming into 3rd gear, locking itself into a dangerous transmission fault "limp mode." The diagnostic scans post-update indicate a failure of the molded lead frame/speed sensor. According to Ford's official technical service bulletin for recall 24S37, physical replacement of the molded lead frame is an explicitly authorized remedy when diagnostic codes appear following the software flash. However, both the local servicing dealership (Midway Motors Ford) and Ford Corporate Customer Service are actively refusing to perform this physical safety repair free of charge. They are wrongfully claiming that because my vehicle has over 200,000 miles, it is disqualified from financial assistance. They are confusing a federal, non-

Read out is showing power steering assist fault. Steering is locking up and screaming. Shows there was a recall for this but that this vin was not on the recall. now it is saying service advance trac.

The contact owns a 2014 Ford F-150. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that the transmission unexpectedly downshifted. The RPM's increased and the powertrain warning light illuminated. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 24V444000 (Power Train) months prior to the failure. The dealer was made aware of the failure but provided no assistance. The contact was informed that the diagnostic test and repair were not covered under the recall. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 206,000.

The contact owns a 2014 Ford F-150. The contact stated that while driving 70 MPH, the rear wheels locked up, causing the contact to lose control of the vehicle, and the vehicle stopped suddenly. The contact regained control of the vehicle after 3 attempts. The contact stated that there was no warning light illuminated on the instrument panel. The contact referenced NHTSA Campaign Number: 26V237000 (Power Train); as a possible cause for the failure; however, the VIN was not included in the recall repair. The vehicle was taken to the dealer but was not covered under the recall. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 150,000.

I was driving on the highway at about 60-70 mph and my truck shifted into first gear with my tires basically locking up and slid along the highway. I brought my truck into a ford dealership and they told me they couldn’t get it to replicate the incident so they turned me away. I personally replaced my battery terminals and it hasn’t done it again. Now I will be driving and randomly my truck will rev bomb and my gauge cluster will shut off and it shows up with an orange wrench symbol but when I turn the car off it resets. The research I’ve done it can come from a speed sensor or the lead frame. I know 2014 fords have a recall on transmissions but my truck does not have a documented one but there is something funky going on with it.

Battery alarm came on twice while running errands less than a mile from home. Parked vehicle in driveway and checked battery connections - everything perfectly tight. 3 hours later had to extinguish flames at front base of engine. DL3Z-14300-D caused electrical fire and see now the part has been discontinued.

See attached document for complaint.

I brought my 2014 Ford F-150 to Gentilini Ford in Woodbine NJ in response to recall notice number 24S37 on XXX for an issue with the molded leadframe on the 6R80 transmission. The recall gave the option of reprogramming the existing leadframe or replacing the leadframe. My leadframe was reprogrammed and not replaced. Shortly after the recall while driving back to [XXX] from NC, the transmission dropped into first gear while cruising down a narrow road causing the back tires to chirp. Several dash lights then came on and the transmission went into limp mode which included rough shifting, sluggish starts, no speedometer or several gauges. When I made it to a point where it was safe to pull over, I immediately turned off the truck and did a visual inspection to make sure there was no damage. I returned to my truck began researching the issue online and quickly realized that it was caused by the actions taken during the recall. I placed several calls to Ford with no recourse. In late May of 2026, I learned of a new recall aimed at the correction of the recall and Ford was replacing the leadframes that were reprogrammed. Upon further research, I learned that late year 2014 f-150's with the 6R80 transmission were not included in the recall. I am reaching out for help in forcing Ford to include my truck in the recall. The issue happens almost every time I drive now and will eventually reset back to normal mode after several stops and restarts. It is a very dangerous situation when m

The contact owns a 2014 Ford F-150. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the brake pedal was depressed to the floorboard, and the vehicle rolled to a complete stop. No warning lights were illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with a leaking brake cylinder. The contact was informed that the brake cylinder was leaking onto the brake booster. The contact was informed that the brake cylinder, the brake booster, and the brake fluid reservoir needed to be replaced. The vehicle was not repaired. The contact referenced an unknown recall; however, the VIN was not associated with a recall related to the failure. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 170,000.

My 2014 Ford F-150 previously received Ford's brake master cylinder recall repair under the previous owner in November, 2016. On XXX, at approximately 108,372 miles, we were towing our travel trailer and had just begun a planned vacation. Within approximately five minutes of leaving home, a warning chime sounded and a "Brake Fluid Low" warning appeared on the instrument panel. I immediately exited the roadway and pulled into the nearest gas station to determine the cause. Within moments, the brake pedal traveled completely to the floor, leaving the vehicle with virtually no braking capability and making it unsafe to operate. Because the truck was towing our travel trailer, we had to disconnect the trailer in the gas station parking lot. The truck could not be driven safely and had to be towed to Kent Parsons Ford in [XXX]. My son had to bring his own truck to tow our travel trailer home because our truck was no longer capable of doing so safely. Kent Parsons Ford inspected the vehicle and documented the following diagnosis on the repair order: "Verified customer's concern. Found master cylinder seal failed and filled booster with DOT fluid." The dealership replaced the brake master cylinder, brake booster, brake fluid, and related components. The failed components may no longer be available for inspection because they were replaced during the repair. I paid $1,793.38 for the repair. The dealership's diagnosis documents the same failure mechanism described in NHTSA Recall 20V-

While driving on the highway Vehicle appeared to downshift into to low of a gear range causing me to almost lose control of the vehicle

On July 2, 2026, the vehicle was brought to an authorized dealer for a scheduled appointment to resolve active Safety Recall 26S45 / NHTSA Campaign 26V378 (6R80 transmission sudden downshift defect). The dealership refused to perform the recall software update, claiming it was not needed for the vehicle. On July 12, 2026, while traveling at highway speeds on a public highway, the transmission suffered the exact un-commanded sudden downshift described in the recall. The violent mechanical force instantly snapped the rear driveshaft in half and severed the undercarriage air conditioning lines, creating a sudden, life-threatening loss of control and wheel speed reduction on a live highway. The vehicle is now permanently disabled due to the dealer's refusal to fulfill a federal safety mandate.

Exited side street onto main 4 lane main road with a median. Upon pulling out wrench light appeared causing all power to engine to cease, oncoming traffic almost hit me. Upon limping into median I shut vehicle off and turned back on. Wrench light was gone, check engine light was there. Code P2112, P2004, P2009.

I am the owner of a 2014 Ford F-150 that is experiencing sudden, unexpected downshifts into a lower gear while driving at highway speed. This has happened on multiple occasions and has nearly caused accidents, including loss of vehicle control momentarily. This defect matches the description of Ford safety recall 26S45 (loss of signal between the transmission output shaft speed sensor and the powertrain control module, causing unexpected downshift into first gear). Despite this, my vehicle was not included when I checked recall status, even though I have an open Ford claim number: Cxh-08412521-F6L5j4. I am filing this complaint to ensure this incident is on record given the ongoing safety risk, and to request that NHTSA confirm whether my VIN should be captured under recall 26S45 or a related campaign (24S37/24V444). Description: Transmission suddenly and dramatically downshifts at highway speed without warning, causing loss of vehicle control and near-accidents.

I purchased a set of 4 LT275 /65 R18 BF Goodrich K02 tires on 8/19/2022 from Discount Tire. I notice some cracking along the front passenger side wall. I took it to Discount Tire and the verified that all four tires were doing the same thing. My family was driving at high speeds multiple places the days before finding this out. It should be able to be confirmed. It was inspected by the store. I had no prior issues with the tires.

NHTSA / Center for Auto Safety Formal Complaint Vehicle Information: * Year / Make / Model: 2014 Ford F-150 * Component Category: Service Brakes, Hydraulic / Anti-Lock Brake System (ABS) * Affected Part: ABS Hydraulic Control Unit (HCU) / Valve Assembly (Part # DL3Z-2C215-A / DL3Z-2C215-C) Incident / Issue Summary: I am reporting a critical safety concern involving a failure of the Anti-Lock Brake System Hydraulic Control Unit (HCU) on my 2014 Ford F-150, combined with an indefinite manufacturer supply chain failure that renders the vehicle unable to be repaired to safe operating standards. The electronic ABS control module on my vehicle was inspected and rebuilt to functional specification; however, diagnostic testing confirmed that the internal mechanical/solenoid valves within the Hydraulic Control Unit (HCU) assembly are stuck/failing. This internal valve failure disables key safety features, including Anti-Lock Braking (ABS), Electronic Stability Control (AdvanceTrac), and Traction Control. Upon attempting to purchase an original equipment manufacturer (OEM) replacement HCU assembly through Ford Motor Company and authorized dealerships, I was informed that the critical safety part is on an indefinite nationwide backorder with no estimated delivery date (ETA). Safety Risk & Regulatory Impact: 1. Loss of Safety Features: Without a functional HCU assembly, the vehicle operates without active ABS or AdvanceTrac traction/stability control, significantly increasing the risk of

The truck suddenly decided to downshift from sixth gear to second gear. This has happened twice on our way to Staunton, Virginia.

The transmission system failed, consistent with an active federal safety recall issued for this vehicle. The primary symptom was a complete failure to start. The vehicle is currently at Helfman, where it was towed for recall repair. It is available for inspection upon request at that location. A vehicle that fails to start due to a transmission defect under active recall creates a safety hazard in that the owner may be stranded — including in unsafe locations or conditions — without warning. The vehicle became completely inoperable with no ability to move it under its own power, requiring emergency towing. Additionally, a transmission defect can create unpredictable vehicle behavior risk if the failure had occurred while the vehicle was in motion rather than at rest. The vehicle was towed to an authorized Ford dealership, which received the vehicle for recall-related repair and initially indicated it was awaiting parts — implying the recall defect and the vehicle's no-start condition were acknowledged. The dealership subsequently refused to complete the repair without providing a clear written explanation. UNKNOWN whether a formal written diagnosis was issued.

Traveling at 65mph on I-275 in Tampa while changing lanes vehicle suddenly downshifted to 1st or 2nd gear enough to cause the vehicle to jolt and squawk the rear tires. The vehicle remained in this state with elevated rpm's and gear indicator was blank. This has occurred on many occasions and is extremely dangerous. It has been an ongoing problem that Ford refuses to correctly solve. It's already been in for service under prior recall which hasn't really solved anything. The 2013 models had the same issue which Ford issued a replacement of the lead frame, yet now they continue to slap bandaids on with software patches. The software doesn't solve the problem of a garbage lead frame.

Hello, I recently brought my 2014 Ford F-150 (VIN: [XXX]) to the dealership regarding Recall 24S37. The vehicle experienced the following symptoms: • Check Engine Light illuminated. • Wrench Light illuminated. • Intermittent loss of power. • Abnormal transmission behavior. • Intermittent no-start condition. • Vehicle would only start after moving the gear selector. The dealership informed me that no physical repairs would be performed because the diagnostic trouble codes retrieved were different from those associated with Recall 24S37. However, the vehicle continues to exhibit transmission-related symptoms, and I am concerned that the underlying condition may be related to or aggravated by the conditions addressed in Recall 24S37. I am requesting that Ford review this case and determine whether additional diagnostic evaluation or repairs should be considered. However, they refuse to accept that the codes have anything to do with the recall, even though it is the same part and the affected sensor that is triggering the error codes on the scanner. They are asking me to pay for the transmission repair because the codes are not the ones approved for the recall, but based on the signs and symptoms the truck is showing, it is a chain reaction that triggered the previously mentioned failures. Thank you INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2014 Ford F-150. The contact stated while driving at an undisclosed speed, the steering wheel failed to turn in the intended direction. The contact stated that the steering wheel was very hard to steer. The vehicle was taken to an independent mechanic where it was diagnosed with a failing electric power steering module. The contact was informed that the electric power steering module needed to be replaced. The vehicle was not repaired. The dealer was not made aware of the failure. The contact referenced a recall; 14V31600 (Steering) however, the VIN was not associated with a recall related to the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 298,829.

The back-up camera is not working properly. The image is flipped when the camera comes on

The contact owns a 2014 Ford F-150. The contact stated that while his girlfriend was driving approximately 50-55 MPH, the vehicle unexpectedly downshifted into first gear, and the rear wheels locked up, causing the vehicle to stop in the middle of the road in a slightly sideways position. The powertrain warning light was blinking, and the infotainment screen turned black. Upon restarting the vehicle and shifting to drive(D), the vehicle responded briefly and made a clunking sound. The instrument cluster and the infotainment system were inoperable. The vehicle was towed to an acquaintance's residence, who informed the contact that the VIN was included in NHTSA Campaign Number: 24V444000 (Power Train). The vehicle was then towed to the contact's residence. The vehicle was later towed to the dealer at the owner's expense. The dealer diagnosed the vehicle and determined that the PCM had failed and could not connect to the computer at the dealer. The dealer determined that the PCM needed to be replaced for further diagnostic tests. The vehicle was not repaired. The manufacturer was contacted, and several complaints were filed. The failure mileage was approximately 204,000.