2019 Jeep Wrangler

Defect. Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.

Remedy. Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.

Defect. Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."

Risk. An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.

Remedy. Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.

Defect. Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk. Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy. Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.

Defect. Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk. Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy. FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.

Defect. Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and Ram 2500, 2019-2020 Ram 1500 and 2020 Jeep Gladiator vehicles. In the event of a crash, a front seat belt retractor may not properly slow the occupant's forward movement after locking.

Risk. In the event of a crash, if the front seat belts fail to lock, there is an increased risk of injury.

Remedy. Chrysler will notify owners, and dealers will replace the front seat belt retractors, free of charge. The recall began November 12, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W67.

Defect. Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4" or 12" radio displays. A software error can cause the rearview camera image to remain displayed after the vehicle has been shifted out of reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."

Risk. The lingering rearview image can distract the driver, increasing the risk of a crash.

Remedy. Chrysler has notified owners, and dealers will update the radio display software, free of charge. Optionally, owners can choose to remotely update their software via an Over-The-Air (OTA) update available as of May 1, 2020. The recall began April 27, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W30-W37.

Defect. Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk. The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy. Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.

Defect. Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and 2019 Ram 1500 vehicles. These vehicles have improperly machined steering column stub shafts that may break, possibly causing the steering wheel to detach from the steering column.

Risk. If the steering wheel detaches from the steering column, the driver may lose control of the vehicle, increasing the risk of crash.

Remedy. Chrysler will notify owners, and dealers will inspect the steering column, replacing it, as necessary, free of charge. The recall began April 5, 2019. Owners may contact FCA US customer service at 1-800-853-1403. Chrysler's number for this recall is V29.

Defect. Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.

Risk. An unexpected reduction in steering ability, can increase the risk of a crash.

Remedy. Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.

On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received …

In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) …

Instrument Panel Cluster (IPC) Blank XZ1 Warranty Extension Customers may experience the following: SYMPTOM: ● A blank electronic vehicle information center (EVIC) in the IPC. No information is displayed for the fuel level, temperature gauge, odometer, outside temperature, PRNDL and optional digital speedometer Fig. 1. IMPORTANT! The speedometer and …

D-25-15 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles

ID-25-11 Rev. C Aluminum Filiform Corrosion Warranty Policy and Vehicle Digital Imaging (VDI) Pre-Approval Process - ALL Vehicles

Instrument Panel Cluster (IPC) Blank XZ1 Warranty Extension Customers may experience the following: SYMPTOM: ● **A blank electronic vehicle information center (EVIC) in the IPC. No information is displayed for the fuel level, temperature gauge, odometer, outside temperature, PRNDL and optional digital speedometer Fig. 1. IMPORTANT! The analog speedometer …

MODULE - STEERING CONTROL & COLUMN

Shimmy Felt In Front End

DAMPER - NONE

"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."

FCA Caribbean Warranty Bulletin ID-23-10 Rev. A (XF1) Steering Damper – Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)

Warranty Bulletin D-23-09 Rev. A (XF1) Steering Damper – Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)

Voltage regulator chip failure can cause the engine to stall or fail to start completely. Interior dashboard lights and dome lights along w/ windshield wipers going off without prompted happen after vehicle shutoff. Had to jump it to begin to start at times. Similar to recall U87.

Cluster panel failed. Dashboard is completely dark (ie. no speedometer, fuel guage. etc)

On [XXX], my 2019 Jeep Wrangler Unlimited Rubicon (2.0L turbo) caught fire in the engine compartment while driving, at approximately 101,437 miles. The fire started near the turbocharger and heat shield area. There were no injuries, but the vehicle was moving on a public road with four occupants, including two young children in car seats in the rear, when the fire started. The vehicle had been returned to me four days earlier, after approximately 2.5 months at Preferred Chrysler Dodge Jeep of Muskegon, MI for a timing chain replacement. After the fire, I found that the coolant reservoir hose had come off its fitting, and the hose barb appears to have been broken and the hose pushed back on. Several under-hood trim fasteners were also missing. My best assessment is that coolant sprayed onto the hot turbo/exhaust components and ignited. The vehicle has not been altered since the fire and is available for inspection at Watson's in Ludington, MI. I reported the fire to the manufacturer. They directed me to take it to the local dealer, then instructed the dealer not to inspect or work on it. The case was escalated internally, but as of 10/15/2026 no manufacturer inspection has occurred and no one has contacted me. The cause has not been confirmed by a dealer or independent shop. The fire occurred within the vehicle's Certified Pre-Owned warranty period. As of this filing, the manufacturer has not provided towing, rental, or any other assistance. INFORMATION REDACTED PURSUANT TO TH

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 40 MPH, the instrument panel cluster suddenly went black. The contact pulled to the side of the road and waited for a family member to follow closely behind to ensure a safe drive, as essential driving information was no longer visible. The vehicle was taken to the dealer, where it was diagnosed that the instrument panel cluster had failed and required a complete assembly replacement. The vehicle was pending repair. The contact learned of NHTSA Campaign Number: 24V652000 (Electrical System); however, the vehicle was not covered under the recall because the VIN was not included. The manufacturer was notified and confirmed that the VIN was not included in the recall. The failure mileage was approximately 81,000.

FCA US sent me a written warranty extension (15 years/150,000 miles) for the instrument panel cluster on my vehicle, covering a blank EVIC display with no digital speedometer, fuel level, temperature, odometer, or PRNDL. My vehicle has this condition intermittently. As I was traveling approximately 55 mph my power steering, antilock brakes, speedometer, fuel gauge, traction control, all-wheel drive, and emergency brake warning lights came on/off. I actually lost power steering and was unable to turn the vehicle off. I reached out to Jeep and advised them of this and that I received the letter for the instrument panel cluster XZ1 and I thought this was related. I read the letter to them word for word, and they had the dealership perform the recall on my clutch. I didn't know until all of the same things happened again and I checked the receipt to confirm the work performed. I reached out to Jeep the same day and that was more than a week ago. I now have a new service transmission light. My vehicle is not safe to drive and they still don't even know why I called. My case number with Jeep is 98166358.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 45-50 MPH northbound on the Hutchinson River Parkway, the steering wheel failed to operate as needed. The vehicle was uncontrollable and started drifting towards the left before crashing into the highway barrier. The message “Electronic Driver Assist” was displayed. The vehicle was towed to the body shop. The manufacturer was contacted by phone, and the contact spoke with a customer representative, and a case was opened. The contact was informed that the investigating team would reach out in 2 to 4 days. An inspector had been assigned by Geico Insurance Company. The approximate failure mileage was 59,000.

The 48-Volt Lithium-Ion eTorque Hybrid Battery Pack (Mopar Power Pack Unit/PPU) on my 2019 Jeep Wrangler Sahara Unlimited (~55K miles) failed. The failed component may be available on video by the dealership. Check engine light first appeared early XXX. Earliest dealership appointment was late August 2026. At that visit, dealer diagnosed DTCs P0A94 (recurring, including P0A94-03) and U0412, and performed a software update flashing the BPCM (Battery Pack Control Module) firmware from 05057870AN to 05057870AV per a Technical Service Bulletin. This was covered under warranty at no charge; vehicle was returned to me. Days later, the check engine light returned along with a battery warning light and additional indicators, including ABS among others I could not fully identify. The vehicle then lost power and stopped running while in the roadway, disabled in an active lane of travel — a safety hazard to myself and surrounding traffic. Vehicle was towed to the dealership XXX. On this second visit, the dealership attributed the failure to moisture exposure and corrosion at the PPU connector/harness, denied warranty coverage, and charged me $4,561.90. I received the repaired vehicle XXX. I opened a case with Stellantis Customer Care (Case #XXX) with case manager [XXX] to request a technical review of the failure and the warranty denial. [XXX] stated he contacted the dealership five times seeking information or resolution and received no response. He offered rental car reimbursement up

My 2019 Jeep Wrangler has experienced a failure of the Blind Spot Monitoring system. The vehicle repeatedly displays a “Blind Spot Alert Temporarily Unavailable” warning, causing the blind spot detection system to become unavailable while driving. The vehicle was inspected and diagnosed by an authorized Jeep dealership. Diagnostic trouble codes were present, and I was advised that Stellantis has issued a service bulletin addressing this condition and that the diagnostic codes indicate replacement of the mirror glass/components associated with the blind spot monitoring system. This concerns me because the system is an important safety feature designed to alert the driver to vehicles located in areas that may not be visible in the mirrors. When the system fails, those warnings are unavailable. Despite this being a documented issue addressed by a manufacturer service bulletin, I was informed that there is currently no recall and that the necessary mirror replacement is not covered under my extended warranty. I am filing this complaint because I believe a recurring failure involving a vehicle safety system should be documented and investigated to determine whether other Jeep Wrangler owners are experiencing the same problem and whether further manufacturer action is warranted.

The left front brake line has failed and needed replacement on 2 occasions. The brake line gets a restriction that causes the vehicle to veer to the right under braking. It also is causing uneven rotor and caliper ware resulting in a high pitched squeal under load.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, one of the brake calipers locked up, causing the vehicle to veer from side to side during acceleration. The vehicle was driven to an independent mechanic, where a technician diagnosed it with a seized brake caliper. Due to the constant dragging, the brake pads wore excessively and failed to slow the vehicle properly, extending the stopping distance. The brake parts were replaced, and the vehicle was repaired.

While driving my 2019 Jeep Wrangler, the vehicle suffered a major electronic/CAN-network failure. Service Shifter, ABS and ESC warnings appeared, the wipers activated on their own, controls malfunctioned, and power-steering assistance failed while the vehicle was moving, making it extremely difficult to steer. My two young children were in the vehicle. Jeep dealer diagnostics showed widespread communication faults involving steering, ABS/brake, transmission and other control modules. The dealer replaced the power-steering assembly and RF Hub, but the problem remains. On the first drive after repair, the ABS and ESC warnings repeatedly flashed on and off at highway speed. Interior lights are also flickering. I am concerned another network failure could again disable steering assistance or compromise ABS/braking-related safety systems and cause loss of vehicle control or a crash.

Vehicle went into dealer for diagnostic, update PCM for hill start assist and cruise control failure. Dealer identified pcm update was not done when clutch recall performed. Instrument cluster update was pushed as well. Instrument cluster bricked. headlight indicator only functioning light on cluster. All gauges and information screen are dark. no functionality. Car has been sitting at the dealership since July 1, 2026 waiting on a replacement instrument cluster.

2019 Jeep Wrangler JLU experienced intermittent CAN-C communication failure. Vehicle has repeatedly experienced simultaneous loss of multiple electronic systems. On September 7th 2026, while driving, vehicle unexpectedly lost electric power steering, windshield wipers activated without command, ABS/TPMS/ESC warning lights illuminated, and vehicle subsequently would not shift into gear after stopping at a traffic light. Hazard lights would not activate. After shutting vehicle off, vehicle would not enter ACC or restart normally. Opening driver’s door unexpectedly caused vehicle to enter ACC. Manipulating the CAN-bus wiring/STAR connector behind the glove box has historically temporarily restored normal operation. Vehicle has previously required repair to this wiring/connector, and the failure has recurred. This has been occurring for at least 3 years and since 60,000 miles. This presents a significant safety hazard because steering assistance, shifting/propulsion, and signaling were simultaneously affected while driving. It is a known Chrysler issue (FCA STAR Case S2108000146) and should be recalled as there is a CLEAR and present danger with this ongoing issue.

The IPC Cluster completely blank. Unsafe to operate vehicle, as speed was unknown, unable to read fuel gauges, and unable to see any warning lights. Experienced the exact problem noted in Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, and my VIN is not listed on the recall list.

Getting the well know Jeep "Death Wobble". Was advised by Carvana when I bought this vehicle that it had an open recall for this exact issue (Manufacturer Recall Number CDJR XF1) due to the Steering Damper having air in it. However, when I contacted a Jeep dealership to get it fixed, I was told there is no recall for the Steering Damper for my specific vehicle. When I look it up on NHTSA, there isn't a recall listed on here either. Whenever I hit transitions in the pavement while driving above 50mph, I get the death wobble on the front of the vehicle. I have not yet had it repaired, but I plan to do so regardless of whether a recall exists. This is clearly an affected vehicle that was wrongly excluded from the manufacturer's recall for the Steering Damper on vehicles manufactured prior to August 11, 2020. My vehicle was manufactured in April 2019, so it is definitely in the correct date range, and with the exact same issue of others that were recalled. The only reason I have not crashed is because I've taken EVOC classes (for driving firetrucks and ambulances), and I am able to control it when it does happen. There were approximately 65k miles on the vehicle when I bought it, and there is about 72k miles now. It has been happening since I bought it in December 2025 from Carvana.

The IPC Cluster stopped working and the screen is completely blank. It is unsafe to drive since I don’t know how fast I’m going, how much gas is in the tank, and inability to see any warning lights. The recall for this is Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, which I have but my VIN is not listed on the recall list. It should be!

Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel was blank. The vehicle was taken to the dealer and was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced. The vehicle was awaiting the repair. The manufacturer was notified of the failure and referenced NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The failure mileage was unknown.

The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact failure mode detailed in NHTSA Campaign 24V-652 (Jeep Recall 30B), but the manufacturer has not yet added this VIN to the recall population.

ABS pump and module combination is making brake calipers to not released. It’s been two times in 6 months my brakes are used up and calipers locked. Jeep knows this issue across its brand of vehicles but not called for a recall. Parts are also in back order that says lot of vehicles has issues. Confirmed with local dealership.

VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an

The vehicle is experiencing severe, premature galvanic corrosion on the doors, hinges, and hood due to a documented factory defect where aluminum panels press directly against steel hinges without proper isolation (acknowledged by the manufacturer in TSB 31-001-24).This is a critical structural and safety hazard covered under Federal Motor Vehicle Safety Standard (FMVSS) 206, which regulates door locks and door retention components. The advanced sub-surface corrosion is causing the metal surrounding the door hinges to degrade and oxidize, causing the paint to blister, bubble, and flake off. Over time, this structural failure poses an imminent safety risk of causing the door hinges to seize or bind, potentially jamming the doors shut during an emergency and trapping occupants inside the vehicle. Furthermore, the degradation of these hinge components creates a severe risk of the doors failing and opening unexpectedly while the vehicle is in motion at highway speeds.The manufacturer is refusing to address this structural defect because the vehicle passed its 5-year calendar warranty window, ignoring the fact that this sub-surface chemical reaction takes years to visibly manifest. This defect requires a formal safety investigation and an expanded recall to protect drivers from door-retention failures.

The contact owns a 2019 Jeep Wrangler. While the contact's daughter was driving at an undisclosed speed, the heated steering wheel feature was enabled; however, the heated steering wheel feature failed to function as intended. In addition, the contact became aware of a burning odor. The contact deactivated the heated steering wheel feature. The vehicle was taken to the dealer, where it was diagnosed with interior melting of the steering wheel. The contact was informed that the steering wheel and the steering wheel housing needed to be replaced. The vehicle was not repaired. The contact was informed that the parts were ordered. The contact referenced an unknown recall; however, the VIN was not associated with a recall related to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 71,663.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 60 MPH, the vehicle suddenly lost motive power and stalled, and the vehicle went into LIMP Mode. The check engine warning light was illuminated. The driver was able to safely move the vehicle to the side of the road. The vehicle was taken to an independent mechanic to be diagnosed, and the contact was informed that the ABS module had failed. The local dealer was contacted and advised that the replacement part was on backorder and referred the contact to the manufacturer for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the replacement part was not available. The failure mileage was approximately 68,482.

The front left (drivers side) caliper stuck and the the brake line needs replaced. The caliper sticking was causing extreme heat that could have caused a fire as well as brake failure. The repair shop confirmed that the parts need replaced. No warning messages were ever appear. Additionally, the left brake line from Mopar is not available and there are almost a 1000 on back order. The Jeep is not drivable and no parts available for the foreseeable future to fix the problem.

Instrument panel cluster has malfunctioned. Spedometer, tachometer, odometer, fuel guage, oil temperature, tire pressuer, and several other dashboard displays both analog and digital are not functional. The instruments on the dashboard have gone blank and do not provide a reading when the car is powered on. As a consequence of the instrument panel cluster failure, I am unable to see my exact speed, potential vehicle warning indications, and fuel levels while operating the vehicle putting the safety of myself and others at risk. The vehichle has a history of dealership and mechanic inspections. No warning lamps, messages, or other symptoms were evident prior to the failure of the instrument panel cluster.

Instrument panel cluster failing making it difficult to determine mph, fuel in vehicle, mileage, etc. panel was flashing and blacking out while driving creating a distraction, photos could not be obtained during worst of incident because actively driving.

There was a recall done on the clutch system back in 2023 and now the same problem has occurred, and I have to replace my entire clutch system.

Instrument panel cluster failure in my 2019 jeep wrangler unlimted sport. instrument panel cluster +9 Stellantis (Jeep) recalled certain 2019 Jeep Wranglers (Campaign 24V-652 or Recall #30B) because their 3.5-inch instrument panel clusters can short-circuit and go completely dark. This causes you to lose your speedometer and critical warning lights, increasing crash risks. Dealers replacement . Thing is none of all 4 are honoring this recall. Im having the same issues as this recall. FCA, NHTSA, CHRYSLER/JEEP, STELLANTIS. ALL 4 i have called even made a complaint and all i get is so rry cant help you cause my vin number is not on the recall yet having the same recall issues. And i have to drive back to [XXX] tomorrow from [XXX] i pray that i dont get into any accident INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle stalled. The contact pulled over and waited for several minutes before restarting the vehicle. The vehicle was taken to the dealer, who replaced the wiring harness, but the failure persisted with the speedometer and fuel gauge fluctuating and the instrument panel icons flashing. Additionally, the vehicle was jerking and experienced a loss of power steering assist while driving. The vehicle was jumpstarted. The vehicle was taken back to the dealer; however, the vehicle was not yet diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 82,000.

The contact owns a 2019 Jeep Wrangler. The contact stated that the horn was inoperable. The contact attempted to depress the horn on several occasions, but the horn failed to operate. The contact's husband attempted to depress the horn, and the horn failed to operate. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 50,000.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the Check Engine warning light illuminated. The vehicle was taken to O'Reily's, where a portable diagnostic machine was used; however, no fault codes were retrieved. The contact stated that the check engine warning light was an old warning light. In addition, the contact was informed that the vehicle could be driven. The contact stated that while driving to the residence, the check engine warning light turned off. The failure reoccurred, and the engine seized. The contact stated that the vehicle rolled near the shoulder of the road. The contact became aware of smoke coming from the engine compartment. The contact stated that a good Samaritan stopped and assisted the contact. The contact and a good Samaritan became aware of fire coming from the engine compartment near the battery. The good Samaritan attempted to extinguish the fire with a sweatshirt, then used a jug of water from inside the vehicle. No injuries were sustained. The vehicle was towed to the local tow yard. The Carvana dealer where the vehicle was purchased was made aware of the failure. The vehicle was then towed to a repair shop assigned by Carvana. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,000.

The 48V eTorque Power Pack Unit (PPU), BPCM, and associated cables failed on my 2019 Jeep Wrangler, causing the vehicle to stall and lose all acceleration while driving on the highway. All components are available for inspection upon request. In June 2025, a non-Jeep service center identified stored diagnostic code P0A9C-00 (48V hybrid battery temperature sensor circuit performance failure) along with multiple low voltage codes in the power steering system. The technician noted the issue needed to be addressed by an authorized Jeep dealer, as there was insufficient information to perform a repair on the 48V hybrid system. In September 2025, while driving on the highway, the engine stalled and the vehicle completely lost acceleration and would not restart. The vehicle required towing to an authorized Jeep dealer. A sudden and unexpected loss of acceleration and engine stall on a highway creates an extreme risk of rear-end collision and potential serious injury or fatality to the driver and other motorists. The problem was confirmed by an authorized FCA/Jeep dealer who found the same diagnostic code P0A9C-00, along with corrosion buildup on the 48V connector pins and BPCM pins. Two separate FCA STAR cases were opened by the dealer. The Power Pack Unit Battery was identified as the failed component. The dealer confirmed that the 48V cables required for repair are currently unavailable through Chrysler under any parts specifier, meaning FCA cannot supply the necessary parts to re

Went to start the jeep and the entire dash cluster was out. I had just gotten it serviced 2 days before it went out and there was no warning or indication that the cluster panel was damaged. Due to this issue I’m unable to see any speed, gas levels, signaling, oil level and any other signal indicators from the dash. This is extremely problematic and renders the vehicle unsafe to drive. It was inspected by the dealership and another mechanic and both parties confirmed the dash cluster was broken and needed to be replaced and that several other 2019-2020 jeep wranglers had been brought in with the same problem.

3 calipers seized at the same time. Replaced all 3. After leaving the mechanic my front passenger seized again, went back to the mechanic & they re did the caliper. A week later the front passenger seized again. They replaced the hose (hose was clamped) 3 days later the front passenger hose clamped again causing the caliper to seize.

In June 2025, I had the clutch recall (NHTSA 23V-116) performed on my 2019 Jeep Wrangler at AutoNation Jeep Southwest in Littleton Colorado. Prior to this recall repair, the vehicle had no transmission faults or warning lights. Following the recall work, I began experiencing a recurring 'Service Transmission' warning. On a return visit, the dealership discovered they had incorrectly reinstalled the shifter cables during the recall repair, making it difficult to shift into first gear. The cables were redone. The 'Service Transmission' warning continued after the cable rework. The dealership performed a software flash on a subsequent visit, which did not resolve the issue. The vehicle later experienced a 'Service Transmission' warning accompanied by a clutch overheat alert and limp mode activation. The dealership has since diagnosed fault codes P082C and P082F (gear lever position sensor circuit high) and is recommending a transmission range sensor replacement at my expense. The dealership has acknowledged they cannot confirm the root cause of these codes. When I contacted Jeep Customer Care, they called the dealership and accepted their assessment that the issue is unrelated to the recall repair. I believe the ongoing fault codes are a direct result of the defective recall remedy, specifically the incorrect shifter cable installation and subsequent cable disturbance during rework. I am requesting NHTSA investigate whether the recall remedy as performed at this dealership is de

Stellantis FCA should be required to extend paint warranty due to bubbling on hood and hinges. There is a known issue but needs to expand out to layer model years. My vehicle has never been in an accident and if was a few months newer Stellantis would’ve covered an 8200$ repair. Hood hinge paint replacement

My speedometer blacked out couldnt see the fuel gage or speedometer. Light flickering, auto park engages, steering wheel locks up.

The center cluster instrument panel went completely black. This affects seeing any warning lights, tire pressure, speedometer, mileage, fuel amount, etc. The problem has been confirmed by auto shops. No way to fix except replacing the entire thing and my VIN has not been included in any recalls.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel became inoperable. The contact stated that the instrument cluster began to dim and subsequently went completely blank. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 112,000.

What component or system failed or malfunctioned, and is it available for inspection upon request? After diagnostics of multiple 'no communication' codes, it was determined that the CAN buss star connector was faulty. The part has been replaced, but is available for inspection. How was your safety or the safety of others put at risk? The malfunction caused repeated warning lights and loss of steering at unpredictable times. Luckily I was always able to put on my hazard lights and get out of the path of traffic. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? Yes, a variety of warning lamps and messages over a period of 10-12 days, which would disappear after restarting the vehicle (restarting was necessary to get the steering working again). Messages such as traction control, auto on/off, and check engine light were a few different ones. They came and went so quickly it was hard to catch them all while I was focused on getting safely off the road.

Heated steering wheel connector melted inside sccm. Repairs needed are a new wiring harness and sccm. Vehicle went up in smoke

Jeep engine stopped running while driving on high way 20.Had to coast to stop in middle of side street.Jeep did start back up but would not go into drive until an hour of trying to get it into gear.Drove it home.Next morning I started jeep but would not go into drive.It was stuck in park.

I was driving my 2019 Jeep Wrangler Unlimited Sahara 2.0T/AT to the gym with my spouse. No Check Engine Light, Jeep Temps were perfect. All gauges operated as it should, so there was no sign of trouble. The vehicle was OFF. We parked and walked into the gym and then into the 1 set of exercises, Someone yelled in the gym that someone's truck was on fire. We ran outside and Lo and Behold it was our Jeep. The Engine Compartment Was totally Destroyed. Please Look At the Pictures for Reference.

The contact owns a 2019 Jeep Wrangler. The contact stated that while starting the vehicle, the instrument panel became inoperable, turning on and then shutting off. The contact stated that while driving, the instrument panel was blank. The vehicle was taken to the dealer, where it was diagnosed, and it was determined that the instrument cluster had failed and needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 103,000.

See attached document for complaint.

Instrument panel cluster dashboard failure, found a massive recall online for Wranglers 2018-2024 for this issue, called dealer who informed us our VIN was not under this recall, but we have a Wranger 2019 with the same issue so should definitely qualify. Called JEEP who informed us our VIN was not under this recall and they won’t do anything about it. This issue is deemed a SAFETY HAZZARD per recall, and we do qualify but they say our VIN specifically does not. This has to be illegal as well as unsafe. Unable to see mileage, gas, safety alerts, etc. because of outage.

RE: Safety Concern – Instrument Cluster Failure Consistent with NHTSA Recall 24V-652 Dear Sir or Madam: Regarding our 2019 jeep wrangler vin# Milage of 74602.9 on 3-22-26 We are writing to report a safety-related defect involving a 2019 Jeep vehicle exhibiting instrument cluster malfunction consistent with conditions described in NHTSA Recall No. 24V-652 (FCA US LLC). Although this vehicle is not currently included within the recall’s identified VIN population, it is exhibiting substantially similar symptoms, including: Intermittent loss of speedometer function Tachometer irregularities Intermittent or complete failure of the instrument cluster display Recall 24V-652 identifies a defect in the instrument panel cluster (IPC) which may result in loss of critical driver information. As recognized by the National Highway Traffic Safety Administration, such failures may increase the risk of a crash due to the driver’s inability to accurately monitor vehicle speed and operating conditions. Given the similarity between the observed condition and the defect described in the recall, this raises a concern that the issue may extend beyond the currently defined VIN range. Accordingly, we request: A formal review of this vehicle for potential inclusion within Recall 24V-652 or any related service campaign; and Appropriate corrective action consistent with applicable safety and warranty obligations. We will also be submitting this matter to the National Highway Traffic Safety Administratio

Engine lights on Glass Recalibration failed multiple times. Engine failure when Jeep comes to a complete stop vehicle totally shuts down and needs to be restarted. When manufacture was contacted: not able to sell new engine. Resolution used engine with same issue. No real Resolution.

The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, there was a misfire coming from the engine, and there was a backfire coming from the exhaust system. Additionally, there was a coolant intrusion in cylinder #3 and a burning in the head gasket. The contact stated that the engine overheated and the vehicle failed to restart after it was turned off. The catastrophic engine failure was attributed to coolant intrusion into the combustion chamber, which caused severe internal damage. The vehicle was towed to an independent mechanic, where the engine was being replaced. The vehicle was not yet repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 61,000.