2021 GMC Yukon XL

Defect. General Motors LLC (GM) is recalling certain 2021-2024 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, and Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles equipped with a 6.2L V8 gas engine. The connecting rod and/or crankshaft engine components may have manufacturing defects that can lead to engine damage and engine failure.

Risk. Engine failure increases the risk of a crash.

Remedy. Dealers will inspect the engine, and as necessary, repair or replace the engine. For vehicles that pass inspection, dealers will add higher viscosity oil, install 6 oil fill cap, replace the oil filter, and update the owner's manual. Repairs will be performed free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Cadillac customer service at 1-800-333-4223, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is N252494000.

Defect. General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.

Risk. Rear wheel lock-up can increase the risk of a crash.

Remedy. Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.

Defect. General Motors, LLC (GM) is recalling certain 2021 Yukon, Yukon XL, Chevrolet Tahoe, Chevrolet Suburban, Cadillac Escalade, and Cadillac Escalade ESV vehicles. The daytime running lights (DRLs) may not deactivate when the headlights are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. Daytime Running Lights that do not deactivate as intended may cause a glare, reducing visibility and increasing the risk of a crash.

Remedy. Dealers will provide an over-the-air (OTA) update for the Body Control Module software, free of charge. Owner notification letters were mailed December 15, 2022. Owners may contact GM customer service at 1-888-988-7267, Chevrolet customer service at 1-800-222-1020, or Cadillac customer service at 1-800-458-8006. GM's number for this recall is N222382220.

Defect. General Motors, LLC (M) is recalling certain 2021-2022 Cadillac Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon, and Yukon XL vehicles equipped with third-row seats. The rivet that retains the buckle to the mounting bracket in the left or right side third-row seat belt buckle assembly may have been improperly formed.

Risk. A seat belt with a deformed rivet may not properly restrain an occupant, increasing the risk of injury during a crash.

Remedy. Dealers will inspect the rivet head formation on both the left and right side third-row seat belt buckle assemblies and replace seat belt buckle assemblies, as necessary, free of charge. Interim owner notification letters informing owners of the safety risk were mailed September 28, 2022. Owner notification letters were mailed on November 1, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N222372380.

Defect. General Motors, LLC (GM) is recalling certain 2021 GMC Yukon, Yukon XL, Cadillac Escalade, Escalade ESV, Chevrolet Suburban, and Chevrolet Tahoe vehicles. The rear wheel driveshaft assemblies may have internal components that were not heat-treated properly, possibly resulting in driveshaft failure.

Risk. Driveshaft failure can cause a sudden loss of drive power, increasing the risk of a crash.

Remedy. Dealers will replace the left and/or right rear driveshaft assemblies, free of charge. Owner notification letters were mailed on March 14, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N212351030.

Defect. General Motors, LLC (GM) is recalling certain 2021 Cadillac Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon, and Yukon XL vehicles. The fuel pump power control module may cause the fuel pump to fail or operate intermittently, which can interrupt fuel flow to the engine, and cause an unexpected engine stall.

Risk. An engine stall increases the risk of a crash.

Remedy. Dealers will replace the fuel pump power control module, free of charge. Owner notification letters were mailed on October 14, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; or GMC customer service at 1-800-462-8782. GM's number for this recall is N212332040.

Defect. General Motors, LLC (GM) is recalling certain 2021 Cadillac Escalade, Escalade ESV, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, and Yukon XL vehicles. A software issue may cause a loss of power steering assist at startup or while driving.

Risk. Increased steering effort, particularly at lower speeds, increases the risk of a crash.

Remedy. The power steering module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed July 13, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; or GMC customer service at 1-800-462-8782. GM's number for this recall is N212333900.

Defect. General Motors, LLC (GM) is recalling certain 2021 Buick Envision, Cadillac CT4, CT5, Escalade, Escalade ESV, Chevrolet Tahoe, Corvette, Suburban, GMC Yukon, Yukon XL vehicles. The communications gateway module incorrectly processes a loss of communication with the sensing diagnostic module (SDM), causing the air bag malfunction indicator light to inconsistently illuminate.

Risk. The air bag malfunction indicator light may fail to warn the driver of a problem with the air bag, increasing the risk of injury.

Remedy. The communications gateway module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on July 1, 2021. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is N212338110.

Defect. General Motors, LLC (GM) is recalling certain 2021 Cadillac Escalade, Escalade ESV, GMC Yukon, Yukon XL, Chevrolet Suburban, and Tahoe vehicles with third-row seating. The third-row outboard seat belts may have been entrapped or misrouted behind the outboard seat-folding mechanism, which could result in damaged seat belts.

Risk. A damaged seat belt can break during a crash, increasing the risk of injury to the occupant.

Remedy. GM will notify owners, and dealers will inspect the third-row outboard seat belts, replacing any damaged seat belts, and rerouting them if necessary, free of charge. The recall began on April 21, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Cadillac customer service at 1-800-458-8006. GM's number for this recall is N202313000.

Defect. General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Risk. If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.

Remedy. GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.

Defect. General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Risk. If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.

Remedy. GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.

Defect. General Motors LLC (GM) is recalling certain 2021 Chevrolet Suburban and Tahoe and GMC Yukon and Yukon XL vehicles. During general assembly, a repair involved removal of one or both front seats. The attachment bolts for the front seats may not have been properly reinstalled after the repair was completed.

Risk. If an occupied front seat has loose or missing attachment bolts, it may move during a crash, increasing the risk of injury to the seated occupant.

Remedy. GM will notify owners, and dealers will inspect the seat attachments for both front seats and install attachment bolts as needed, free of charge. The recall began December 21, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-888-988-7267. GM's number for this recall is N202312720.

**Mileage at repair:** 76,165 miles **Component:** Fuel Pump Power Control Module While driving my 2021 GMC Yukon XL on [XXX] on a treacherous stretch decending [XXX] the engine unexpectedly stopped running, resulting in a complete loss of propulsion. This occurred on a section of interstate where there was no safe shoulder or suitable location to pull off the roadway. The unexpected failure created an extremely dangerous situation, exposing me and other motorists to the risk of a serious collision. The vehicle was subsequently towed, diagnosed and repaired by Darrell Waltrip Buick GMC in [XXX]. The dealership documented diagnostic trouble code P129F, "Fuel Pump Driver Control Module Fuel Pump Speed Signal Incorrect." The technician verified that the control module had proper electrical power, that there was no pin damage or connector fitment issue, and that the module required replacement. The dealership's written diagnosis specifically acknowledges that a failing fuel pump driver module can cause the engine to shut down. The original factory-installed module was replaced with GM part number 13554821, and the vehicle was subsequently tested and confirmed to operate correctly. The repair was performed at no charge, and GM provided a loaner vehicle while the replacement part was unavailable. I am particularly concerned that General Motors has previously acknowledged this same type of safety hazard under NHTSA Safety Recall 21V-739 (GM N212332040), involving fuel pump power con

High oil consumption, will have oil changed and days later need oil, catalyst converter failed causing what was said for the check engine light to come on, truck now has a shutter around 50 mph, my radio is in and out, and sometimes it sounds like a computer shutting down. It has been one thing after the next.

On September 21, 2026, my 2021 GMC Yukon XL Denali with the 6.2L V8 engine experienced a serious engine failure at approximately 83,330 miles while traveling on Interstate 10 near Litchfield Road in Arizona. The vehicle developed engine knocking and subsequently stalled, leaving my family and me at risk on the highway. This was a serious safety concern because the engine failed unexpectedly during operation. The GMC dealership determined that the engine needed to be replaced under warranty. The replacement engine was installed in October 2026, and I received the vehicle back on October 13, 2026. My concern is that the dealership installed a remanufactured engine, and I have not received sufficient documentation confirming whether the replacement addresses the underlying defect associated with the GM 6.2L engine failures. I am concerned about the possibility of another catastrophic engine failure, particularly while traveling at highway speeds with my family. I am requesting that NHTSA investigate this engine failure and determine whether the replacement engine adequately addresses the safety defect. I believe these failures present a serious risk to drivers, passengers, and other motorists.

Rear wheel lock up for a slight second and then down shifted and revved way up to high RPM then went into reduced power. then slowed down and had to drive about 15 miles an hour. to shop mechanic.

The vehicle is consuming every bit of oil at about 1500 to 1800 miles of the 3000 mile guidelines before the next oil change. No leaks. No smoke. No knocking in motor.

While driving the vehicle on a roadtrip in Missouri, the engine lost power and had a flashing check engine light. Upon diagnosis by three different technicians, the 6.2L Engine needs replaced after only 123000 miles. The lifters and camshaft have failed. This is a known safety issue and numerous recalls have been implemented, but my high end Denali is mysteriously absent from the recall. This is unsafe and unsatisfactory.

Part number 13554821 fuel pump control module has failed 2 times. April 2023 on Interstate 95 near Savannah GA in very busy traffic. Vehicle buckled and seized, just barely made it to the shoulder of the road. Same part failed again 9/18/26 while turning onto Sunrise Hwy in NY another very dangerous situation as we were stranded in the middle of a very busy intersection

Engine coolant control valve has failed three times. This last time so severely the car forced me to come to a complete stop in the middle of a busy street. Dangerous to drive while severe reduced acceleration is all that’s available during the episodes.

6.2L engine has the oil change update, and engine failed recently. took vehicle for repair to Golling GMC dealer. waiting on feedback.

Vehicle has been consuming engine oil at a rate of approximately 1 quart per 500 miles. On XXX, owner added 1 quart of oil in [XXX], then drove a round trip to [XXX] and back (approx. 860 miles). On XXX at 55,329 miles — only 9 days and roughly 860 miles after that quart was added — an oil change was performed at an independent shop; the technician noted no oil was present on the dipstick prior to service. On XXX at 55,829 miles — exactly 500 miles later — the vehicle was taken to an authorized GMC dealership, and the dipstick again showed no oil prior to service. The dealer began the manufacturer's oil consumption test protocol, performing an oil and filter change and other maintenance. Within approximately 74 miles of this service (current mileage 55,903), the engine began making an audible knocking noise. Oil level was checked and confirmed full/normal, ruling out low oil as the cause. The knock has been intermittent — not present at cold idle start, but returning during driving conditions, raising concern about potential engine failure or loss of power while driving. They can not get it back in till XXX. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The rod bearing failed while traveling at highway speeds, so yes our safety as well as others traveling on the interstate. It is available for inspection. A dealership inspected and confirmed the reported problem. The manufacturer is aware of the persistent problems with these vehicles' engine components, reliability and safety. There were not any symptoms, warning lights, etc. prior to failure. I had just purchased the vehicle and it was inspected by two independent mechanics prior to failure. I have contacted the manufacture to find that my VIN was not covered under the recall. The recall covers vehicles manufactured starting 3/1/2021, my vehicle was manufactured 10/2020. THE RECALL SHOULD BE EXPANDED TO COVER ALL OF THESE VEHICLES.

According to the GM Dealership the rod bearing failed disabling the engine. Dealer recommends replacing the entire engine. This consistent with recall N 252494000-N252494003 but my VIN is not included in the recall. Estimated repair $11,200. Our family was traveling roughly 55 mph on the interstate at the time of incident.

The engine failed, shop confirmed and replaced motor. No warning lamps on dash.

My 2021 GMC Yukon XL Denali with the 6.2L L87 V8 has experienced two significant lifter/valvetrain failures. The first occurred at approximately 6,500 miles and was repaired by a GMC dealer. That failure involved cylinder #4, including a collapsed/stuck lifter and bent pushrod. The current failure occurred at approximately 110,269 miles. The vehicle initially operated normally. While traveling about 10 mph and approaching a major thoroughfare, the engine suddenly began making a loud knocking noise and the vehicle began shaking violently. There were no warning lights or other symptoms beforehand. Three children were in the vehicle. When the driver attempted to accelerate, the vehicle failed to gain speed normally, and additional accelerator input made the knocking and shaking significantly worse. The check-engine light began flashing, and “Service ESC” and “Service Traction Control” warnings appeared, along with multiple other warning lights. The engine continued running. The driver made a U-turn before entering the major roadway and drove about 0.2 miles very slowly back home. An independent repair facility diagnosed P0305, cylinder #5 misfire. Moving the ignition coil and spark plug did not move the misfire, and the #5 spark plug was oil-soaked. A GMC dealer later confirmed a stuck lifter on cylinder #5 and advised that the failed lifter damaged the camshaft. My concern is the sudden loss of normal acceleration and severe engine malfunction without warning, especially becaus

I own a 2021 GMC Yukon XL Denali equipped with the 6.2L L87 V8 engine. On September 10, 2026, we checked the engine oil and discovered that it was approximately two-thirds low. Mechanical inspection confirmed that the engine is consuming and burning oil internally rather than losing it through an external leak. The vehicle’s last oil change was performed in May 2026, and it is still more than 1,000 miles away from its next scheduled oil change. The vehicle provided no low-oil, low-oil-pressure, check-engine, or other dashboard warning, despite being severely low on oil and having its alerts enabled. I had no indication that the engine was operating with an unsafe amount of oil. I am concerned that the continued internal oil consumption could cause premature engine damage, engine seizure, or sudden loss of propulsion without adequate warning. I regularly use this vehicle to transport my young children. My VIN is not currently included in Recall 25V-274, although my vehicle has the same model year and 6.2L L87 engine involved in the ongoing NHTSA investigation. I am reporting this confirmed internal oil consumption and lack of driver warning so that problems occurring in currently excluded vehicles can be properly documented and investigated.

I purchased this vehicle 06/14/2026 The vehicle dash started lighting up like a Christmas tree. It was taken to GM Ed Morse Freedom Chevrolet X 3 separate occasions. The lights in the dash were intermittent. Dealership couldn't duplicate the issue. I was told if they aren't active they can't duplicate. The vehicle continued to illuminate on and off after it was returned July 26th. Then August 23 i was driving and it died right in the highway putting me in a bad spot in traffic. I. There was no illuminated symbols in the dash it just died as the symbols them lit up in the dash. I had it towed by AAA thinking just a battery or starter. I was told by GM dealership the engine seized. Propulsion, metal in the oil and the crankshaft failure. The exact recall problem. My Vin fell just outside of GM internal N252494003 program of 150,000 10 year extended warranty. I have 114, 689. 2021 yukon Denali. THE exact engine failure GM put out. GM is refusing to replace the engine. The engine has been torn down. I received pictures of my claim above. It's still at GM . I've opened a corporate GM case. I'm hitting a brick wall

We had to have an engine replaced because of engine failure. The new engine was provided by GMC free of charge. The second engine also failed and was also replaced by GMC.

Our 2021 YukonXL started running rough and the check engine light came on. We took it to the shop the next day and was told there was complete lifter failure and that we need a new engine.

Vehicle is equipped with the 6.2L L87 V8 engine. Prior to receiving the dealer service for Recall 25V-274, the vehicle experienced a distinct highway vibration, powertrain shudder, and fluctuating/jumping RPMs on the highway. The dealer subsequently performed the recall remedy by updating the vehicle to the thicker 0W-40 oil specification. However, the underlying transmission torque converter had already suffered catastrophic failure due to the powertrain stress/shudder and required a complete transmission replacement at 84,000 miles. I am reporting this because the initial 6.2L engine defect and subsequent recall remedy overlap heavily with severe powertrain and torque converter failures at low mileage

The engine started knocking and vehicle shaking while on interstate. vehicle was towed to service center and they determined that one valve was stuck and another one turned 90 degrees and the cam shaft was also ruined. It was required to replace the engine as that was a less costly option than replacing the damaged parts. A dash light came on and was flashing while my daughter was driving it to [XXX]. The vehicle was towed from the parking lot they were at when reaching [XXX]. Unsure of where the engine went to after the service center removed it, but I think they had to send it back to GM. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I have a 6.2L that we took in with bad rods due to the cam. The fixed the motor and now it is consuming oil and GM says it is normal. Normal for an engine to consume quarts of oil?? I cannot trade out of the vehicle because of the extreme depreciation that these vehicles have incurred due to the known engine issues. I know others are having the same issues I just want GM to make this right and help loyal customers.

My 2021 GMC Yukon Denali features the 6.2L L87 V8 engine. This vehicle was previously serviced for the GM voluntary recall regarding engine bearing failures, and the dealership completed the remedy by inspecting the motor and changing the oil to the thicker 0W-40 specification. Since completing this recall fix, the vehicle has developed an intermittent rough idle and sputtering behavior. The dealership has been unable to duplicate the intermittent issue and claims it falls under normal behavior. I am filing this report because my vehicle is exhibiting post-recall remedy engine degradation, matching the exact failure patterns outlined in the NHTSA Engineering Analysis EA26005 escalated on August 20, 2026. This intermittent sputter represents a severe safety hazard regarding potential sudden loss of motive power while driving.

Driving on the freeway the engine started making super loud knocking noises for while going 70mph . Then it immediately died everything turned off no power I was barely able to get it off the freeway while coasting. And my husband tried to push it off the road more but when it dies we are not able to put the car in neutral !! It’s a push button gear shift ! When there’s no power the buttons don’t work!! It was 105 degrees out that day in Sacramento , the car had zero power the battery is not the problem . The motor is blown and the car hasn’t started since that day. These cars are dangerous to just die in the middle of the freeway! The motor has already been replaced in Feb 2026, we bought it in march of 2026 with 57k miles on it. I added about 12k miles and the motor blew up again!

Lifter/camshaft/engine failure. GM knows this is an issue with these models/years. They only want to cover half of the repair sticking me with a bill for $5600. Safety is a concern because they know this is an issue and not issuing a recall currently. I waS driving when this happened which could have caused me to get into an accident. Very dangerous. Car is currently as GMC Started by showing low oil in between oil changes last year. Went in for an oil change and told them about it. Dealership told me it was the air hose box and that they didn't see any other issue. I believe they are told to lie to get each customer further out of warranty. I was driving and all of a sudden the car started violently shaking and lights started flashing at me.

2022 GMC Yukon XL suffered catastrophic transmission failure at approximately 87,000 miles. An ASE-certified transmission repair facility determined that the torque converter failed, resulting in transmission damage requiring over $7,000 in repairs. GM declined any assistance solely because the repair was performed by an independent ASE-certified facility. I am concerned that a major transmission component failure at this mileage may represent a broader defect, particularly given transmission-related service bulletins and NHTSA Recall 26V085 affecting certain 2022 Yukon XL vehicles.

Was driving the vehicle at 70 mph on the highway without any issues for several hours and suddenly the vehicle lost power and had no propulsion. It went into neutral automatically and the engine shut off while driving. Thankfully I was on a downward slope and could steer the vehicle off the very busy highway. Once safe, I tried to restart the car but the engine would not start or turn over. Roadside assistance came to help as well as a flatbed tow truck. It was taken to a nearby GMC dealer but it remains completely dead despite the battery being fully charged and all of the electronics working. No known error codes are showing up. It’s an L87 engine and was part of the GM recall. The recall work was completed in Nov 2025.

Engine failed. Had to be towed to the dealer to get a new motor. It was part of the 6.2l L87 recall

Driving on busy road when heard a squealing from the engine bay of the vehicle. Moments later the vehicle lost power. It was a very dangerous situation traveling approximately 45mph on a multi-lane road in urban St. Louis Missouri. There was not a check engine light prior. The vehicle had a recall performed per GMC instructions prior (this amounted to a different viscosity oil....). The breakdown stranded my family and I while on vacation in another city. The vehicle was towed to a local GMC dealership and was diagnosed as a seized engine related to the recall. The engine is scheduled to be replaced as no cost through GMC's extended service. They have not provided coverage for the towing, for the multiple ride shares needed to get around on vacation, for the rental car needed to get home, or a rental car to help us with day-to-day life during the estimated 6-8 weeks we will be waiting. My family was at risk, other motorists on the parkway were at risk. It was pure luck and quick thinking that saved injury or loss of life. It is completely unbelievable GMC is letting these vehicles be on the road for peoples safety and for the money people pay as a consumer.

I am filing a safety complaint regarding my 2021 GMC Yukon. While driving on the highway during a long-distance trip from [XXX] to [XXX], my vehicle suddenly experienced a serious loss of power, drivability issues, and loss of propulsion. The vehicle began shaking violently, slowing down unexpectedly, and struggling to maintain speed while in active highway traffic at highway speeds. At the time of the incident, the vehicle displayed a warning message indicating “Conditions Not Correct for Shift” at approximately 127,506 miles. Shortly after, the vehicle set diagnostic trouble code P0011, which relates to the engine and transmission system not performing as expected and indicates an issue with the Variable Valve Timing (VVT) system affecting engine timing and performance. The vehicle also entered a reduced performance state, and I was advised through the vehicle’s warning system to reduce speed, avoid hard acceleration, and avoid heavy load conditions. Despite following these precautions, the vehicle continued to run poorly and became increasingly unsafe to operate in highway traffic. This created a serious and potentially life-threatening situation, as I was traveling in fast-moving traffic and the vehicle lost normal propulsion and stability. I had to carefully maneuver out of active traffic lanes to avoid a potential collision. The vehicle eventually required roadside assistance/towing due to its inability to operate normally. Diagnostic trouble codes and warning messages

Burning oil too much too fast oil all over motor and engine and white smoke inside the car all records are with GMC DEALER

Engine seized while driving on the highway. This is the same engine that is being recalled and GM has said that the vin is not covered. The vehicle stopped running on a major highway with my [XXX] old son in the car. The dealership is saying this is the exact issue that is part of the larger investigation for GM v8 engines. There were no warning lights at all prior to the engine seizing. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2021 GMC Yukon XL. The contact stated that while driving 55 MPH, several unknown warning lights illuminated, and the check engine warning light started blinking. The contact pulled over and became aware that the vehicle was shaking. The vehicle was turned off and restarted; however, the failure persisted, with smoke coming from the vehicle. The vehicle was repaired under NHTSA Campaign Number: 25V274000 (ENGINE AND ENGINE COOLING); but the repair failed to fix the vehicle. The vehicle was taken to the dealer, where it was diagnosed, and it was determined that the camshaft needed to be replaced and that cylinder #8 was damaged and had detached. The manufacturer was notified of the failure. The failure mileage was 116,204.

This is from dealership “found customers concern of engine light is on and ticking noise found cylinder 4 lifters to be collapsed causing the exhaust gasses to be trapped in the cylinder causing the cylinder wall to dry out and leaving scratches on the cylinder wall recommend replacing motor due to this problem at this time”

The infotainment screen on my 2021 GMC Yukon was previously replaced at the GMC dealership, and this will be my second replacement. It has now cracked even though there was only very light contact. This doesn’t seem like normal wear and tear. I’d really appreciate it if the screen could be inspected, as I suspect there might be a manufacturing issue with these screens. I’m quite concerned about this problem because it almost caused injury to my six-year-old. Please understand my worries, I’m sure many other parents are facing similar concerns with these screens. The cracked glass can be dangerous, especially for families with children.

My family and were traveling to visit family, and the transmission stalled on me on the interstate. I almost had a horrible accident with my kids in the vehicle. The vehicle is in the shop currently and dx with transmission issues. GMC needs to recall and or fix the transmissions in all of their vehicle.

My 2021 GMC Yukon XL recently suffered a failure of its fuel pump control module. This occurred at just 44,000 miles, mere weeks after my manufacturer warranty expired in June of 2026. This issue goes far beyond a financial inconvenience or a matter of consumer reimbursement; it is a severe, life-threatening safety hazard that GM has failed to permanently resolve. My Experience: Sudden Power Loss While Towing The gravity of this part failure became clear during a recent drive. I configuration-matched this vehicle—a heavy-duty Yukon XL with a 6.2L engine and a 4x4 towing package—specifically for its capacity to safely haul heavy loads. While traveling with a trailer attached, the vehicle experienced a sudden, catastrophic loss of engine power. Without warning, the engine sputtered and died. Had this occurred on a steep incline, a blind curve, or in heavy highway traffic, a catastrophic multi-vehicle collision would have been entirely unavoidable. Critical Safety Hazards and Concerns •Inability to Maintain Speed, Loss of Vital Assist Systems, & Compounded Towing Risks Systemic Failure and Inadequate Remediation What makes this situation entirely unacceptable is that this specific vehicle was already subject to previous GM safety campaigns regarding this exact component (including Safety Recall #N212332040 and subsequent Emission Recall #N252516900). GM is fully aware that their supplier produced defective modules that are prone to premature internal short-circuits. Yet, their r

Issue Description: The vehicle experienced a failure of the Dynamic Fuel Management (DFM) system, resulting in a collapsed lifter. This caused a cylinder misfire and a sudden loss of engine power while driving at highway speeds. Safety Concern: While traveling at highway speeds, the sudden misfire and loss of power created a dangerous condition. The vehicle could not maintain speed or accelerate properly with surrounding traffic, significantly increasing the risk of a collision. Failure Details: The issue was diagnosed as a collapsed lifter related to the DFM system. This caused persistent misfiring, rough engine operation, and severe drivability issues. Repair Outcome: Due to the extent of internal engine damage caused by the lifter failure, the vehicle required complete engine replacement.

The contact owns a 2021 GMC Yukon XL. The contact stated that while starting the vehicle, the engine stalled and the vehicle failed to start. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who determined that the fuel pump power control module needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 21V739000 (Fuel System, Gasoline); however, the VIN was not included in the recall. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 59,000.

Check engine light comes on and an alert says "acceleration reduced" dealer says the coolant control valve is bad but the engine never overheats but the fans are running max speed 100% of the time.

While I was driving home from the grocery store with my 4 kids our 2021 GMC Yukon XL (5.3L V8 engine), the vehicle suffered a sudden, catastrophic mechanical engine failure without warning. The engine began violently shaking, lost major propulsion, and dropped into a severe misfire state when we were coming down the highway. This created an immediate safety hazard on the road, as I suddenly lost the ability to safely accelerate or maintain highway speeds while hauling my children.A certified technician diagnosed the issue as a complete failure of the active fuel management hydraulic valve lifters and bent pushrods, a known manufacturing defect explicitly documented in GM Technical Service Bulletin PIP5776F. The internal failure required a total engine teardown and valvetrain replacement, costing over $10,000 out of pocket.General Motors has failed to issue a safety recall for this specific 5.3L valvetrain defect, despite it causing unexpected engine stalls, severe power loss, and immediate traffic hazards for drivers. This defective component poses an ongoing safety risk to families and should be upgraded to a mandatory safety recall. I am afraid to drive it every time I get on the highway in fear it could shut down again.

The contact owns a 2021 GMC Yukon. The vehicle was taken to the local dealer for a routine oil change. While driving, the oil low light illuminated. The vehicle was burning an excessive amount of oil. The local dealer was contacted again, but the vehicle was not diagnosed or repaired. The manufacturer was contacted, who referred to the local dealer. The failure mileage was approximately 149,000.

The vehicle suddenly began vibrating noticeably when idling and at low speeds. About 30 minutes after this started happening a warning lamp lit up. We drove the vehicle about 2 miles to a local auto parts store to get an initial computer diagnosis of the issue. The test resulted in a code of "P0304" which detected a cylinder #4 misfire and recommended a fuel injector replacement. We brought the vehicle to a local mechanic to get the issue further evaluated. After this evaluation, it was determined that the cylinder #4 misfire was related to a lifter failure. The mechanic explained that this situation could possibly have caused more damage, specifically to the camshaft, but that job was bigger than he was willing to take on. He recommended we get the vehicle towed to the dealership for further evaluation. He also informed us that this situation was common with the engine in this vehicle and GMC is aware of it. He directed us to some articles online that elaborated on the potential known issues related to the automatic fuel management (AFM) system and the related engine damage. The vehicle was towed to a local GMC dealership for evaluation. They found the failed cylinder #4 with associated lifter failure and damaged camshaft. We went forward with the repair at the dealership. We asked the dealership about the known engine issues with this vehicle. They acknowledged the widespread issues but informed us that our particular VIN has not been included in any recalls or safety notif

I took my GMC Yukon in for a recall. They changed the oil, programmed my module, changed the cap, and tested the engine, saying it was good. I took it on a trip, 7000 miles later engine locked up.

The vehicle drove normally earlier in the day with no major drivability concerns. Later, reverse gear suddenly stopped functioning and the engine would rev abnormally without the vehicle moving properly while in reverse. Shortly afterward, while driving, the vehicle displayed the warning message “Reduce Acceleration – Drive with Care” and began losing acceleration and propulsion. The vehicle would not accelerate normally and later could not exceed approximately 20-35 MPH. The condition created a significant safety concern due to sudden loss of acceleration and propulsion while operating in traffic. The engine RPM would increase abnormally while the vehicle failed to respond properly in drive and reverse. An independent mechanic inspected the transmission and found diagnostic trouble codes P0747, P0776, and P0700 related to transmission pressure control and valve body operation. Inspection also revealed significant metal contamination, sludge, and clutch material inside the transmission pan and filter. Reverse and 2nd gear were determined to be failed/burnt internally. The vehicle was later transported to an authorized GMC dealer for inspection. Dealer confirmed reverse gear would not engage even after adding transmission fluid. Vehicle is currently available for inspection.

The vehicle has experienced recurring suspension, drivability, and pulling issues associated with the 4-corner air ride leveling suspension system since early ownership. The first major incident occurred at approximately 4,600 miles when the vehicle displayed suspension warnings and would not accelerate properly past highway speeds. Since that time, the vehicle has repeatedly experienced pulling during acceleration, unstable ride behavior, suspension/leveling concerns, alignment-related issues, and drivability instability. The problem has been reproduced multiple times and documented through approximately 16 repair visits and roughly 74 cumulative days out of service. Dealership service records include repeated suspension inspections, drivability evaluations, wheel alignments, and related repair attempts. The issue remains unresolved and the vehicle is currently back in service again for the same concern. The recurring pulling and instability create safety concerns because the vehicle does not consistently track properly during acceleration and normal driving conditions. Suspension warning messages and drivability symptoms first appeared early in ownership while the vehicle was still under factory warranty. I have also found many similar owner complaints online involving the same suspension system in comparable GM full-size SUV models.

*gas tank had become partially dislodged from the undercarriage. *Entire family was in vehicle at time of incident, including three small children. The safety of an entire family along with any others that may have been on the road, if the car would have combusted due to the gas tank which had just been filled to capacity. *vehicle has been at Mark Christopher GM dealership for over one month. *dealership service dept claims someone tried to steal gas tank. *Mercury insurance company claims mechanical failure. *No warning given from vehicle. We heard a dragging noise while we were driving, pulled over as soon as possible. Upon inspection, it was observed that fuel tank had begun to leak fuel from dragging on the freeway.

The forward collission system continues to perform phantom braking while driving in traffic resulting in near rear end collisions. The GMC dealer refuses to fix it without charging me for more diagnostic work, which has already been done twice. What is my recourse?

We brought vehicle in while still in warranty complaining of rough running engine and dealership said they couldn't find anything wrong. 2000 miles over warranty the Engine fails with all characteristics of the L87 bearing lifter issue. Now GMC does not want to replace without charging us a ton of money.

Our 2021 GMC Yukon XL with the 6.2L engine suffered a catastrophic failure requiring the engine to be replaced. The diagnosis was very similar to the GMC 6.2L engines that have been recalled for safety and failure reasons however our vehicle was not included in the recall. The engine only had 75,924 miles and was maintained to the manufacturer's maintenance schedule. The cost to replace the engine was $11,309.87.

When turning on the car, a message pops up on the dash and will not go away. Dashboard says “ service safety restraint system”