2022 Ford Mustang Mach E

Defect. Ford Motor Company (Ford) is recalling certain 2021-2023 Mustang Mach E vehicles. The rear differential pinion shaft may fracture.

Risk. Differential pinion shaft fracture may result in a loss of drive power, or unintended vehicle movement if the vehicle is in park without the parking brake applied, increasing the risk of a crash.

Remedy. Dealers will repair or replace the rear differential assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed July 13, 2026. Additional letters will be sent once the remedy is available, anticipated in late December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S50.

Defect. Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.

Risk. An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.

Remedy. Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed July 10, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S56. This recall is an expansion of previous NHTSA recall number 23V687.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.

Risk. The inability to enter or exit the vehicle in an emergency increases the risk of injury.

Remedy. Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.

Risk. A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.

Remedy. The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles previously repaired incorrectly under recall number 22V-412. The high voltage battery main contactors may overheat.

Risk. An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.

Remedy. Dealers will update the on-board software, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S14.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.

Risk. An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.

Remedy. Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed December 29, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S56. Vehicles included in this recall that were previously repaired under recall 22V-412 will need to have the new remedy completed.

Defect. Ford Motor Company (Ford) is recalling certain 2022 Mustang Mach-E vehicles. The right-rear axle half shafts may have been manufactured improperly, allowing the half shaft stem to break under load.

Risk. A broken half shaft can cause a loss of drive power, or a rollaway could occur while parked if the electronic parking brake is not engaged. Either of these scenarios can increase the risk of a crash.

Remedy. Dealers will inspect the serial number, and replace the right-rear half shaft, as necessary, free of charge. Owner notification letters were mailed September 19, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S55.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles. The high voltage battery main contactors may overheat.

Risk. An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.

Remedy. Dealers will update the on-board software, free of charge. Owner notification letters were mailed on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S41.

Defect. Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E and 2022 Maverick vehicles. The rear seat belt buckles may not be properly attached to the rear floor assembly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 210, "Seat Belt Assembly Anchorages."

Risk. Improperly attached seat belts may not adequately restrain an occupant in a crash, increasing the risk of injury.

Remedy. Dealers will repair the rear seat belt buckle attachments, free of charge. Owner notification letters were mailed January 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C36.

I had put the vehicle into One Pedal Drive mode for the first time on the morning of Aug 29th. Vehicle operated as it should for first few places I drove to and stopped, but then I approached a red light, removed foot slowly from accelerator and vehicle came to a full stop as it should. Approximately 2-5 seconds later, without warning or even the collision avoidance system activating, my vehicle suddenly accelerated into the rear of the stopped truck in front of me. Fortunately no serious injuries but someone could have been killed. My foot was NOT on the accelerator at the time - it was hovering over it while waiting for the light to change to green. My vehicle was taken to Ford for evaluation, but they claim it has to be repaired before they can diagnose/confirm the issue. I am the original owner with no previous accidents or incidents.

Spot welds have failed on the drivers side door. This is a known issue with multiple ford vehicles, though they have not issued a recall for this specific model.

I just had the High voltage battery junction box replaced after being in shop 16 days. Upon arrival to my house yesterday my car would not charge. upon further investigation once the Hvbj connector is replaced a charge of the car to put a full load on this connector is not performed. Instead ford goes the easy route and uses a test drive and other diagnostic test such as there computer to see if the connector is bad. This software does not detect even close to 100 percent of the time a faulty high voltage battery connector there diagnosis software it is flawed. The only true way to ensure proper replacement of this connector has been done is to charge the car with the charging cable that has come with the car and do thermal imaging on the connector. Because this is not being done you are putting peoples lives at risk by not knowing if the work has been done correctly without this thermal imaging test. Eventually if the high voltage battery junction box is replaced and even the slightest mis crimp of the connector is not done properly without putting a charging load on the connector and testing it with thermal imaging testing they are doing the quick and easy thing which does not detect the problem 100 recent of the time by using the on board diagnosis system as well as driving it. Two recalls and NHSTA investigation on the high speed battery voltage box and it still fails. Because of this test not being done I am positive this is why my car has failed again because it is the

See attached document for complaint

The high voltage battery junction box connector has failed. There have been two recalls one software and one to replace this part the high voltage battery junction box with a more robust part to handle thermal loads. As of now there are zero recalls on my car open so they are all done. The first time this component failed was around 24k miles ish it's now 56k miles ish and it has failed again even after two recalls and an investigation around the same exact time. This means one of two things has happened either somehow the recalls by Tim Moran ford where not done properly and somehow the older failed part number was installed in my car or the more likely senario is that fords supposed robust part was just a simple part number change without a robust enough design to handle the thermal load. I would like to think that Tim Moran ford who is independent from for has done there due diligence the first time it was replaced and but the correct part number which leads me to conclude the investigation by the NHSTA that resulted in a part change did not fix the issue at hand and the car is now unsafe to drive as this is the second time it has happened to me on this vehicle. Thank god this time I was not going through a curve and headed off road. Same issue almost exact same failure part gone wrong and same issue to date. I demand not only for myself but the safety of others as a former Quality Assurance Representative of electronics on Hueys and Cobras that this be re investigated imm

I was pulling into a parking lot at low speed when the car suddenly began accelerating rapidly on its own. Fortunately, when I hit the brakes it stopped without incident. However, if someone had been right in front of me at the time - a pedestrian or car - it could have resulted in a crash. I am certain that I didn't hit the accelerator, nor was it pushed by floor mats or anything like that. It is conceivable that when I was turning, my left palm activated the cruise control in some manner, but that scenario wouldn't explain the acceleration part. And frankly, I don't think that is what happened. I love the vehicle and am not trying to get anything out of it. I am a capable driver with good reflexes and experience. I was able to stop it, but if this were to happen to a new driver or senior driver it could result in a crash. I looked on reddit and many others report exact same issues.

I am unsure, but I think it's the High Voltage Battery Junction Box. A week after buying the car used from Aaron Ford of Poway, I received a Safely Stop now warning, then the car broke down on the middle of the turning lane into my job a medical clinic putting myself, patients, other drivers, and my coworkers all on danger as it is a busy street. The hazard lights would not work, and the car would not go into neutral. The next day, all the dealership did was replace the 12v battery, then I only got 1 mile from the dealership before it broke down again in an even more busier and dangerous highway in the slow lane and crosswalk. The hazard lights would not work, and the car would not go into neutral.

The front driver door metal is cracking and breaking. The door makes a squeaking and cracking sound when I open the door. It is the same problem that the Ford Escape doors had. My car is out of warranty and Ford dealers say it will cost $3,000 to replace the entire door. I think Ford should recall the door because it is clearly a manufacturer defect. Here are photos from other customers that have this problem: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My car keeps showing parking break fault. there is a recall for it but it only covers cars built until february 2022 mine was built in april 2022 and it has the same exact damage

The contact owns a 2022 Ford Mustang Mach-E. The contact stated that while driving at an undisclosed speed, the vehicle became inoperable and the vehicle stalled, and the gear shifter was inoperable. The contact exited the vehicle and was unable to re-enter the vehicle because the doors were locked and failed to unlock. The messages "Service Now" and "Battery Management" were displayed on the instrument panel. The pre-collision sensor warning light and several other unknown warning lights were illuminated. The failure had occurred on several occasions. The vehicle was towed to the residence, and the batteries were replaced. The contact researched the issue and became aware of an unknown recall; however, the VIN was not included. The vehicle was taken to a dealer, where it was determined that the battery management system needed to be reset. The vehicle was repaired, and the dealer advised the contact to drive the vehicle for 30-40 miles. However, after approximately 3 miles, the message "Stop Now" was displayed on the instrument panel, and the failure persisted. The manufacturer was not notified of the failure. The failure mileage was approximately 40,000.

Ongoing issues with forward facing radar preventing collision assistance and adaptive cruise control along with lane keep assist from working. Ford knows about this. There is even a TSB. A car manufactured in an era that requires collision prevention should not be allowed to have significant camera faults that prevent safety systems from functioning properly. Unfortunately, the plan for many is to continue operating without these important safety features and crashes will occur as a result. Ford should be required to properly fix their radar system functionality in the Mach-E.

On 6/4, I completed a long road trip of over 650 miles. When I got back into my vehicle to move it to where it would be parked for the night, it displayed messages for a Powertrain Malfunction/Reduced Power and a High Voltage Battery Warning. I powered the car off and back on within about 5 minutes, and the messages were still being displayed. I connected a code scanner to the car and the car had stored codes P0D0F and P0AA4. Both of these codes indicated a fault with the High Voltage Battery Junction Box, a known issue with the Mustang Mach E. I was able to drive the car to a dealer the next day without incident but am wary of trusting the vehicle to make the same trip back home.

Vehicle stated "PARKING BRAKE FAULT". Driver (myself) discovered electric parking brake was stuck in the ON position and would not disengage. Vehicle could not be moved on its wheels. Vehicle was in parking garage, and driver became stranded for over 24 hours waiting for a low-clearance tow truck with a dolly that could move the vehicle. Ford dealer (Bill Brown Ford) inspected vehicle and discovered wiring immediately behind BOTH rear electric parking brake connectors were corroded and broken. Ford dealer stated there was an active recall for this issue (CSP 22P31 or TSB 22-2143), but that my vehicle's build date was not included. CSP 22P31 only includes build dates before 15 March 2022; Driver's vehicle has a build date of 24 June 2022. Ford dealer stated they repaired the vehicle by completing the procedures defined in recall CSP 22P31, but Ford did not cover the costs or acknoledge it as a recall repair due to the build date. tl;dr: The critical safety defect defined in Ford recall CSP 22P31 affects vehicles built in July 2022, but Ford has not expanded the recall to cover these vehicles. In this case, the corrosion led to DUAL failure of both rear electrical parking brake connectors, causing two exposed electrical circuits and lock-up of the parking brake.

The vehicle’s rear/360 camera system, SYNC/APIM display system, and Reverse Brake Assist/back-over prevention system appear to have malfunctioned. The vehicle is available for inspection upon request. After a software update was performed by the Ford dealer, the vehicle began displaying the warning message: “Reverse Brake Assist not available — See manual.” At the same time, the rear/360 camera image became distorted and unreliable. The camera display has shown abnormal behavior, including distortion, flickering, black/green screen behavior, and an inaccurate or unclear 360-degree view. This issue was not present before the dealer-performed software update. The safety risk is that the rear camera and Reverse Brake Assist are used when backing up to help detect objects, people, vehicles, or obstacles behind the vehicle. Because the camera image is distorted and Reverse Brake Assist is unavailable, the driver may not receive accurate visual information or automatic braking assistance while reversing. This creates a risk of backing into a pedestrian, another vehicle, property, or an unseen object. The problem has not yet been confirmed by a dealer or independent service center after the failure. UNKNOWN whether Ford has reproduced the issue. The vehicle/component has not yet been inspected by the manufacturer, police, insurance representatives, or others after the issue appeared. UNKNOWN whether the issue is caused by the dealer-performed software update, APIM/SYNC software, rea

Was driving my 2022 Mustang Mach-E in "One-Pedal" Whisper mode on. I always drive in that mode because it has a great feature where as soon as I take my foot off the accelerator the car slows down significantly. I feel safer in this mode especially in high traffic or on the freeway. I was very slowly turning into a parking spot in a private parking lot, stepped on brake to put car into Park when the car lurched forward without me touching anything, I had no control of my car no matter how hard I pressed on the brake. My car was driving itself!! when it lurched forward it hit a car parked directly in front of it on its right front side then pushing that vehicle about 2 feet! it did not stop even then, it veered to the right and forward and hit another parked car in the next parking space to the first car that was hit. My car pushed the 2nd car about 2-3 feet before it stopped almost hitting the car parked next to it!! There was an eye witness. This event scared me to death. It was as if someone else was driving my car. I had absolutely NO CONTROL of it. It would NOT STOP. I am soo grateful this happened in a parking lot and not in fast traffic or God forbid the freeway. I would not get back inside my car and never will. We had it towed to a certified repair shop. My car sustained front end & right side front damage. The first car hit sustained right front damage. The 2nd car hit was parked next to the first car hit and sustained right front & right side passenger door damage.

When starting car the instrument cluster was entirely blank. Center infotainment was functional. Due to use of digital dash in the car there were no warning lights or any information including speed available. It is unknown if any safety/driver assist systems were on or off because the display was non-functional. Issue resolved after performing 1 or more software resets documented across the internet but not documented in the manual. Steps to reset appear to be: 1) Perform a hard reset of the car (hold brake 15 sec, release brake 15 sec, press start without bake). 2) Allow car to fully reset and then turn off. 3) Move far enough away from car to trigger locks and put car into low power mode. 4) Return to car and power on. Hard reset did not provide immediate fix. Sync soft reset did not work.

On December 17, 2022, I purchased a new 2022 Ford Mustang Mach-E, VIN [XXX] -Lewis of Hoover Inc. for $48,665.00. Seven months later, the vehicle suffered a complete loss of drive power at highway speed — a near-serious injury (if not fatal) incident on a vehicle Ford had already identified as defective and subject to recall. In approximately July-August 2023 — seven months after purchase with only approximately 13 miles at purchase — the vehicle lost all drive power while I was driving on the freeway [XXX] ) at [XXX] le stalled completely. I was fortunate no vehicles struck me. The vehicle eventually restarted. I drove directly home and did not continue with my planned out of town trip. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6) INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Parking brake malfunction indicated. Ford CSP 22P31 covers repair of the issue for vehichles with a manufacture date before 3/15/22. My vehicle reached the US on 6/22/22. Ford has offered to cover a small part of the repair, but won't include me in the fix due to manufacture date. So Ford ended the program, NEVER FIXED THE ISSUE, and now won't offer to repair my car.

Vehicle shutdown while driving causing total power loss and hitting a parked vehicle. No alerts or notifications were present at the time.

File against: Ford Motor Company Vehicle: 2022 Ford Mustang Mach-E VIN: [XXX] Safety Complaint While driving, the vehicle unexpectedly slowed down, lost power, and became inoperable, creating a serious safety hazard. I was able to pull over safely, but the sudden loss of motive power occurred during active roadway conditions. Dealer diagnosis identified a wiring harness connector failure affecting communication between vehicle control modules. After the repair, the same issue reoccurred within one to two days, again causing loss of power. The vehicle is currently back at the dealership, and the underlying defect has not yet been permanently resolved. This recurring electrical failure represents a loss-of-motive-power safety risk that may indicate a broader wiring harness defect affecting vehicle reliability and safety. Thanks and Regards INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)