2017 Jeep Wrangler complaints

My seat belt is always loose and i have to jam it back in place all the time. I noticed an oil spot on the floor of my garage and it looks like it's the oil cooler housing that is bad. Both of these items are recalled but my vin shows It's not.

Power stop brake hose kit was recalled do to leaks part# BH00139 Amazon order # 112-6473860 / 113-5400733 Recall report 24E-053 Front hose began to leak causing me to loose pressure in the brake system and loosing brakes. Had to have the brake lines replaced

Rear view camera went blank

The oil cooler leaks and the oil runs down the intake valley, down the back of the engine, and onto the frame and the exhaust pipe, this can create a fire hazard under the driver's seat. It also causes oil puddles on the ground which is a hazard. The dealer says oil cooler leaks are the most common issues on the Chrysler/Jeep 3.6L engine. I was told by the dealer, when making an appointment for replacement, that they have to change these oil coolers a ridiculous number of times. I can safely assume that thousands of people are having this same issue, by the amount of blogs, videos and beware when buying warnings and the fact that there are hundreds of aftermarket options for this item. This leak is going to cost me $1,000 to have fixed because they did not engineer it properly, not to mention cleaning the undercarriage and my driveway. Send me a rebate to cover my cost on this flawed engineering issue please!

File has been attached.

Recurrent transmission pan gasket leaking. Repaired and replaced pan and gasket in March 2024 and reoccurred December 2024. Uploaded March Report, currently at dealer for repair 2nd incident now. Vehicles manufactured Nov 2016 had a recall for this same issue but this vehicle wasn’t included due to it being a couple months manufactured. Likely should have been included.

The contact owns a 2017 Jeep Wrangler. The contact stated while the vehicle was at the independent mechanic for a State Inspection, the contact was informed that the fuel tank control valve was cracked. Additionally, an abnormally strong fuel odor was inside the vehicle. The independent mechanic related the failure to NHTSA Campaign Number: 16V849000 (Fuel System, Gasoline); however, the VIN was not included in the recall. The dealer was made aware of the failure but informed the contact that there was no recall associated with the VIN. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 17,548.

Brakes keep dragging, getting hot and seizing. I have done four complete brake jobs and the vehicle has only 40,000 miles on it. Most recent time the wheel rim was so hot you couldn’t put your hand on it. Cost so far, over $6,000. Google searches indicate that this is a recurring issue on this model and year.

Have the rear axle gears chipping/breaking off. Have mentioned this several times to dealer and they said the noise is normal for Jeeps. Took to independent repair shop and he found the gear issue, and asked me if anyone has worked on this rear end before, which would be no. He stated it looks as if someone has broke the original seal on it. I bought it at Performance CJDR in Delaware Ohio, and I'm wondering if something happened to it before I took ownership of vehicle. In process of repair at Bobbitt's Automotive repair in Lancaster Ohio... On my oil changes, the Rear Differential has always been checked OK... Now that vehicle is out of Power train Warranty this happens... My feeling is that this was always an issue with this vehicle, and was being covered up

The contact owns a 2017 Jeep Wrangler. The contact stated that while his wife was driving approximately 30 MPH, the driver's side front brake locked up. The contact stated that his wife had not observed any warning lights being illuminated. The vehicle was driven back to the residence. The vehicle was stopped and parked, and the contact stated that there was smoke coming from the driver's side front wheel well. The contact had not taken the vehicle to a local dealer or independent mechanic. The vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The failure mileage was 91,914.

The contact owns a 2017 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the service brakes warning light illuminated. The vehicle was taken to the dealer where the vehicle was diagnosed with a failure to the frontal impact sensor. The contact was informed that the frontal impact sensor needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 112,000. The VIN was not available.

Driving on Highway multiple times 60-65 mph hit a bump or groove on highway jeep start wobble so bad couldn't hardly control it. July 08, 2024 driving on highway 60-65 mph crossing bridge with grooves or small bump jeep went into wobble, steering wheel flipped upside down I grab tight as it is wobbling to left turning trying not to hit truck as i had no steering control hit another bump thank god and it push to the right and I was able to got to side off highway.. As I am trying to figure whats wrong I look underneath jeep and bar bolted to frame broke frame of 2017 jeep rubicon unlimited.. I had looked at and told that it was very lucky and need to take to jeep dealership frame so weak it can be bent by hand. So please I am thankful it was just me in the vehicle and thankful for the second bump that steered me to the right and i did not hit the truck next to me with kids in it. .

The brakes kept grinding and squealing even after we changed them, next the rotors and calipers were done. Then again one by one everything needed to be replaced and still didn't take and we kept smelling burning coming from the tires. We then replaced the master cylinder and the brake lines and still it won't take. I looked it up and there are countless complaints on this and Chrysler/Jeep do nothing about this huge safety risk ! Answers to your questions 1. Braking system as a whole and yes it can't move 2. If you do not have brakes in a vehicle you cannot stop so unsafe for the driver and everyone on the road bc of collision. 3. Yes my mechanic has re done this job multiple times and agrees there is a defect going on, not normal. 4. I did not know I needed my insurance or the police involved, the dealership is a joke. 5. No warning sensors or a heads up, just does it.

The plastic oil filter housing cracked leading to large oil leaks. This had been leaking for awhile and was not immediately noticed due to its placement in the valley between cylinder banks atop the engine. While investigating separate U-joint noise and driveshaft vibration that came on suddenly at 58,000 miles I found oil all over the driveshaft and traced it to the cracked housing. The repair was ~$650. Mechanics stated this is a common issue when oil change technicians over tighten the filter in the plastic housing.

Transmission failure.

The contact owns a 2017 Jeep Wrangler. The contact stated while attempting to start the vehicle, the vehicle failed to start. The contact stated that the failure had been reoccurring for the past two months. The contact stated that the vehicle was able to be started 50 percent of the time. The vehicle was taken to an independent mechanic and diagnosed with a failed ECM. The contact was informed that the ECM needed to be replaced. The contact was informed of an unknown recall for the 2017-2018 Jeep Wrangler however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 33,000.

While driving in city or highway the engine will shut off randomly, causing the steering almost impossible to turn. Had a few close calls because of this. There is no check engine light to come on.

The contact owns a 2017 Jeep Wrangler. The contact stated while driving at an undisclosed speed, he heard an abnormal ticking sound emanating from the engine compartment, after which the vehicle lost significant motive power. The contact was able to pull to the shoulder of the roadway. After a visual inspection, the contact observed an oil leak underneath the engine compartment. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the piston in cylinder #3. The vehicle was not repaired. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 52,000.

We were driving home from about a location an hour away. We were almost to our home when the transmission started to slip. The hot oil light came on as we were trying to ascend our hill where we live. We all of the sudden saw flames coming out the side of the vehicle. We were able to exit the vehicle and get to safety but the jeep burned completely to the ground. There was only 60k miles on it and it had been well maintained.

The oil cooler leaks when cold and the oil runs down the intake valley, down the back of the engine, and onto the exhaust pipe, which makes it a fire hazard. It also causes oil puddles on the ground which is a hazard when the oil drips splatter other vehicles windshields, as well as making areas slippery for walking. The dealer says oil cooler leaks are very common on the Chrysler/Jeep 3.6L engine. I was told by the dealer, when making an appointment for replacement, that they have to change these oil coolers all the time. Thousands of people have this same issue and there are hundreds of aftermarket options. This leak is going to cost me $1,000 to have fixed because they did not engineer it properly.

Oil cooler housing is made of plastic which melts due to engine heat and the location of the part. It’s a common issue with jeeps and should be recalled as it’s an ongoing know issue with all vehicles with the 3.6 pentastar engine.

Windshield has cracked from cold to hot transition upon vehicle startup without previous cracks or chips affecting said crack line. Available for inspection. Fear of possible windshield failure/full breakage at any given point. Continued cracking during vehicle start up/cold to hot transition happened 4 more times in last 30 days. No dealer, independent service center, manufacturer, police, insurance representatives, or others inspection. No warning lamps or messages.

Oil filter housing cracked

Vehicle started leaking a substantial amount of oil. I took it to a mechanic to have it diagnosed, they stated that the engine oil cooler filter housing is made of plastic and over time warps and leaks. Apparently this is a major issue and has been noted on MANY dodge/jeep vehicles. Prior to this happening, the check engine light came on, I had it diagnosed and it showed as a cylinder 6 misfire. This could have caused major issues in the future if it had not been caught when it was including damage to the bearings and the cylinders (probably what is causing the misfire now).

Oil filter housing is made of plastic and over time the plastic, exposed to heat cycle and elements from being under the plenum, becomes brittle and cracks. The cracks in the oil filter housing create a susbtantial oil leak that drips engine oil onto the exhaust and is a potential for a fire. If the oil level is not properly maintained it could also create a lack of lubrication on the engine for a potential engine lock up while being driven.

When driving at highway speed of appx. 60mph, driver heard a loud pop followed by grinding from under the vehicle. Driver pulled over, and assessed for visible damage, none was seen. A tow truck was called, as the severe grinding sound continued if the vehicle moved at all. It was taken back to the dealership where they discovered that the front driveshaft was completely destroyed. No one was injured, however had this happened during busy traffic it could have caused an incident. The front driveshaft, along with all applicable seals were replaced, at the owners expense as were the towing costs. No cause was found. See also NHTSA ID number: 11156532. My incident was not as severe, however very similar.

Vehicle has severe death wobble that began around teh 90K mile mark. Have spent several thousand dollars replacing front suspension components, shocks, etc...and nothing will correct the issue. When talking to the local dealership, they indicated that they had a fix, but would not guarantee that if I spent XYZ dollars on said fix that the problem would be corrected. There are zero modifications to the suspension and no monster sized tires on this vehicle that would contribute to this. This has been ongoing for 6 months or more. The issue arises at highway speeds, whenever a bump in the road is crossed over. To make the wobble stop involves making a complete stop, which isn't the easiest thing on the interstate with vehicles going past at 70MPH or more...

Dear Sir(or Madam), My Driver Side Rear Cailper locked up (AGAIN) and my Rear Brakes, Cailper and Rotors had to be replaced (AGAIN) this is the second time I had this problem since I purchased this Jeep that I had the Cailper locked up. Jeep has a real problem with this happening. The last time this happened I had a warranty this time I don't. The last 3 Wranglers I have purchased had the same problem, if this isn't a safety problem it shoud be. I have not received a Repair Order as of yet but will summit it when I do get it.

Clockspring failed. No horn, driver airbag, controls to cycle evic and radio stopped working.

Severe "death wobble" at speeds over 40MPH occurs at random times, usually at highway speeds. Have replaced steering damper, shocks, upper and lower control arms, front u-joints, etc....and these repairs have only masked the problem. The OEM suspension is completely unmolested...no lifts, etc. Tires were replaced around 55-60K miles with a slightly wider tire. Wobble started around 95-100K miles. Currently around 115K miles on vehicle.

The contact owns a 2017 Jeep Wrangler. The contact stated that while the vehicle was parked, he became aware of an oil leak underneath the vehicle. The contact stated that the failure had persisted. The dealer was notified of the failure and an appointment was scheduled for a diagnostic test. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 31,000.

The oil filter housing on this engine is made out of plastic and if you search online you will notice that it has failed for many many people. The housing cracks causing motor oil and coolant to mix and leak. We were fortunate to notice it before our engine seized up, but others have not been as fortunate. I believe this defect should be a recall, but there is no recall on this engine even though many many people have experienced this part failing prematurely. Ours failed when the Jeep was under 80,000 miles.

Driving at 65 mph on the highway the hood latches failed and the hood blew back into the windshield, shattered the windshield, and made driving a safety issue. The safety latch also failed. Not able to see out the windshield due to the hood. Spoke with jeep cares and they said the hood latches were not a warranty item. The dealer said it happens frequently that the latches break. I have pictures of the defective latches and filing an insurance claim this week. This is a factory defect that could cause serious injury or death if not fixed.

The airbag light is on. The clocksprin is the failure and is very expensive at the dealer.

2017 Jeep Wrangler Unlimited with 44,000 rear brake calipers sticking and burning smell. Had brake pads and calipers replaced on all 4 wheels. At approx 60K miles, rear brakes were sticking and smoking. Right brakes wearing unevenly compared to the left side, both front and rear. Caliper seals are leaking. Replaced 4 brake hoses, Calipers and Pads AGAIN. At 70K miles rear brakes locked up and caused a fire on the rear passenger wheel which created unsafe driving conditions with 2 small children on board. I had to stop on the side of a 2 lane road with small shoulder, quickly evacuate the children onto the shoulder of the road and extinguish the fire using an on-board suppression device. We then had to wait for towing assistance on the side of the road for 90 minutes. Brakes, Hoses, Calipers replaced all around. Again.

The airbag clockspring is defective. I know other years have a recall on the defective part. The cost of labor and the cost of the part is too expensive. I consider this a safety issue and feel like it should be under a recall like the previous model years.

Airbag light continually goes off and on with alerting beep and light

2017 Jeep Wrangler, approx 46k miles, driven gently (only highway and city), well-maintained. Problems with Brake Calipers seizing. Back Driver calipers/lines/pad/etc replaced. ABS and brakes jammed last week. Front and Back Passenger calipers, rotors, brake fluid lines and brake pads advised by mechanic. Brakes temping 550 - unreadable (temp gun wouldn't register) Mechanic recommends unsafe to drive because brakes could seize and cause sudden stop and/or accident Dealer says too bad, normal wear and tear. This is our family's 10th Jeep, and NOTHING has happened like this before. Seems like a safety issue perhaps that Jeep should be addressing rather than putting on the consumer (who will no longer purchase Jeeps)

A check engine light came on and when diagnosed it was the Electronic Vacumn Pump which runs the braking system. I see there is a TSB from FCA (Fiat Chrysler Automobiles) about this problem.. Case Number: S1805000006 Release Date: 02/24/2020 Symptom/Vehicle Issue: ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE Discussion: If ABS has C1252-92 Active or Stored do not replace the brake system module (ABS). PCM may also have set P258B-00. The faults are pointing to vacuum pump system having an issue maintaining vacuum levels. Please check the vacuum pump operation, fusing, wiring, and connector for proper functionality. Poor connections, spread pins, damaged connectors are possible causes. Perform the diagnostic for the DTC P258B regardless if it is set or not, since it is more compressive of a test than C1252-92. In addition when checking Vacuum lines, please ensure to check Vacuum hoses and check valves between the engine intake, booster and vacuum pump. Because the check valves only allow flow of air on one direction, each vacuum circuit must be checked separately to make sure there are no leaks, kinks or damages. Please refer to the correct vacuum diagram. For KL vehicles: inspect ALL under hood grounds for connection and contact issues. My Jeep is at the Ford Dealership I work at at this time. Didn't want to drive any farther than I had to at this time.

Front driver side brake caliper was sticking on right after I bought the car at approximately 86000 miles! I found an article about there being updated hoses right after my car was manufactured. The updated hoses are on the front brakes. Of course I read this article after assuming it was the caliper cause I couldn't squeeze the caliper piston in. I replaced it, with the same results! After I replaced the hose, its fine now. So I cut the hose in sections to found out where the hose was pinched, and its where the hose is crimped in a metal bracket that bolts to the axle. I have a picture of the part of the hose, I cannot see through tiny 3" section or stick a pin through it! I'm assuming the bracket rusted and pinched that section off.

Jeep caught on fire on the interstate. 17 year old boy had to pull over and escape vehicle. Vehicle left the side of the road even after being in park and brake. Vehicle continued unmanned on interstate into oncoming traffic engulfed in flames. It has not been confirmed by a dealer. Vehicle was inspected by State Farm. NO warnings given prior to incident.

Fuel overfill due to improper design of the filling tube. Caused fuel to spill onto vehicle, bumper and ground. Fire hazard high.

The contact's brother owned a 2017 Jeep Wrangler. The contact stated that while her brother was driving at an undisclosed speed, another vehicle crashed into his driver's side, causing his vehicle to crash into a tree. The contact's brother had no account of what happened the day of the crash. No air bags were deployed upon impact. The contact's brother sustained injuries to his face, was unable to walk, and was transported to the hospital for medical treatment. A police report was filed. The vehicle was towed to a tow yard, where it was deemed totaled by the insurance company. The manufacturer was not made aware of the failure. The failure mileage was unknown. The VIN was unavailable.

The contact owns a 2017 Jeep Wrangler. The contact stated that on various occasions while driving at various speeds, the air bag warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the air bag needed to be replaced. The manufacturer was notified of the failure. The failure mileage was approximately 110,000.

Shortly, after returning home, I was cleaning out my jeep, including my glove box. There is no catch behind the glove box and things fall out the back of the glovebox to the floor particularly get stuck underneath the center dashboard console directly adjacent to the glove box. I had some face masks from Covid that fell out the back of the glove box, and landed underneath the hidden in area of the console between the steering column in the glove box. I reached behind the plastic cover to retrieve the masks and burned my hand on some very hot metal. It was so hot. If I would not have found the masks that fell in there, they would’ve surely started an interior fire in the jeep while I was driving or in my garage. This is very dangerous, my husband also burned himself when he checked on another day when I showed him. This is a serious fire hazard and they need to either completely close off that gap at the glove box or close it off directly below the dashboard where all the controls are for heating and cooling and radio.

My Jeep has been experiencing what is called the “death wobble”. When I get over 50mph, it starts to shake real bad feeling as though my tires are about to come off.

Engine light came on stating cylinder #4 miss fire. After taking it in, the mechanic said that they can repair the head but it will most likely be an issue again in another 30k or it will be another cylinder. They said it is still causing the air to leak. This Jeep only has 51k miles and is in mint condition. After further research, Jeep had previously recalled this same issue on Jeeps a little older than 2017.

While on the highway, cruising at 65 mph, the electronic stability control warning light started flashing and the brakes started to be applied automatically and almost caused an accident and rollover. No trouble codes are shown or captured and dealership can not reproduce the issue. However it has happened more than 5 times and only while on the highway at cruising speeds.

The vehicle has 55,000 miles on it. BOTH brake calipers were stuck and grabbing. A complete front end redo for brakes & calipers at very low mileage. When braking to stop, it was all over the road and unpredictable.

Chrysler has a recall for 2017 jeeps, fuel sending component, campaign #16V84900, but does not include this vin. However, the component is defective from manufacturer in this vehicle. How do I get this vin to be included in recall?