2015 Ford Mustang complaints

All wheel nuts had to be replaced when new tires were replaced Cost for the nuts $226. NO inspected or change the nuts that were swollen. by Ford. Did the recall No06tice end last year in August.

There is a break pedal pad that is broken. It doesn't allow the car to accelerate correctly and car goes in limp mode. All break lights are illuminated when car is turned off. There is a recall for this, but I purchased my car in CA. I think the car was originally a Nevada car. Am I still eligible for the recall even if I didn't get the notification and my state of purchase was not mentioned?

The weld that connects the clutch pedal bar to the tube it pivots in broke on my 2015 Mustang. This makes the pedal wobbly and can prevent the clutch from being fully depressed. For months, the clutch was squeaking. Upon inspection, I noticed the weld was broken. I have not been in an accident because of this, however, the clutch pedal is now loose and can at times hit the 'neutral' switch (which measures full depression of the clutch to allow the car to start), which prevents inconsistent depression of the clutch, leading to unsafe operation.

Seat Belt Tensioner: Seat belt tensioner is not retaining tension. Inordinate amount of slack when taking off belt coupled with slow retraction. Also have noticed lack of tension during sudden stopping. The belt will also not retract up exiting the vehicle. I’ve reported to the dealer and they commented they’ve seen this plenty of times. This seems like a major safety concern.

Hi, I was driving on the freeway and suddenly my car stopped accelerating. I would push the acceleration pedal but it wouldnt speed up. And for a few times it would speed up very much. This was very rapid fluctuation. I also noticed that the cruise control was not working. This was very scary being on the highway with this kind of speed fluctuation. After i came back home, i noticed that the brake light wouldnt turn off at all. After doing some research i found that the brake light switch broke and the car was sensing that the brake was being applied and hence was doing acceleration fluctuations. I also found out that there are many other same vehicles which has the same issue.

The contact's husband owns a 2015 Ford Mustang. The contact while reversing, the rearview camera image was distorted and black. The contact stated that the failure had increased, causing the rearview camera to become inoperable. Additionally, the contact stated that the tailgate had failed to open while using the key fob, while pressing the tailgate release switch inside the cabin and the release button on the decklid. The vehicle was taken to the dealer, where it was diagnosed that the decklid wiring harness needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the vehicle could not be repaired under NHTSA Campaign Number: 22V082000 (Back Over Prevention) because the VIN was not included. The failure mileage was approximately 42,000.

Related to Regional Recall 22R01, the rubber bumper on my brake pedal that engages the brake light switch failed and placed the vehicle in a low power mode. This failure occurred while merging onto the interstate and almost resulted in my being rear-ended by a semi truck. Having never been notified of this regional recall, I was able to verify this was the case after searching forums and YouTube and identifying the pieces of the broken bumper in my floorboard. I find it to be HORRENDOUSLY unacceptable that this was allowed to be handled as a regional recall and no notice was ever produced, as it is a safety-related issue that could have resulted in grievous bodily harm. I am located in Kentucky, which is not part of the named region.

I was driving home from work and all the sudden it went into limp mode, I could barely get her home. Then I found yellow pieces of plastic in my floorboard. My brake light would not go off so I had to unplug the battery. Very scary to have that happen on the interstate, luckily I got off on an exit.

The brake pedal stop bumper in my car disintegrated in the middle of the day and fell off. The brake lights do not turn off anymore and the vehicle can be started and shifted without needing to press the brake. I found a recall # 22S02 for this exact issue but my vehicle is not covered by it (assuming due to region). The vehicle has not been inspected yet.

There is a well known evaporator core issue with the Ford Mustangs/Trucks that were produced between the 2015-2017 models. Freon leaks out of the evaporator core due to poor build quality this creates a white film on the windshield of the vehicle that makes it hard for drivers to see. This happened to me when I first bought my car and I could have crashed but was able to safely pull over and clean the windshield off. This film buildup can happen at anytime and also releases an unpleasant order into the atmosphere that should not be breathed in and is very harmful to the environment. Ford is well aware of this issue and decided to avoid doing a recall to prevent the company from losing money. I am also having an airbag issue on my Mustang this one is current. I have not been in any accidents or driven the car in anyway to make the light come on. The drivers side airbag light is on and is indicating that their is an issue with my airbag system. This is a huge safety concern and I don't want to wait for something to happen for either of these issues to be fixed. The AC issue is new for me with Ford but out of the 4 mustangs I have owned 3 of them have all had recalls for an airbag issue. The first was my 2005 V6 base model. The second was my 2010 Mustang GT. and the third was my 2014 Mustang GT. This is now my 4th mustang and still having air bag issues. Please do something about any of these issues if you can. I am sure numerous of other people have experienced what I am experi

A plastic clip ("Brake Pedal Bumper") broke and fell out of place, causing the brake pedal to no longer reach the brake light switch. The brake lights now remain illuminated permanently, even with the brakes released. This also caused the engine and transmission to go into "limp mode", the engine no longer revving over 2,000 RPM, the transmission not shifting, and hill-start assist and traction control no longer working, making the car unsafe to drive. The brake lights will remain on even when the car is completely shut off and locked, draining and damaging the battery. It is my understanding that this is a known issue, and there was a recall for this in certain states. (Safety Recall 22S02, Regional Recall 22R01). There should be a national recall for this, as the affected part appears to be of low quality, and causes safety issues when it fails, with the car's drivability and lighting affected.

THIS IS A KNOWN ISSUE ON THE 2015 MUSTANGS. THE RECALL ONLY INVLOLVES VEHICLES FROM CERTAIN STATES WITH HIGH TEMPS AND OR HUMIDITY BUT DOES NOT INCLUDE THE STATE OF MISSOURI WHICH SEES BOTH HIGH TEMPS AND HIGH HUMIDITY. DTC CODE P0504. BRAKE LAMP SWITCH HAS ALREADY BEEN REPLACED AND NO ISSUE WITH WIRING. POSITIVE THE PLASTIC STOP BUMPER IS THE ISSUE.

I ran into the existing issue described in "Part 573 Safety Recall Report" NHTSA Recall Number 22V-011, but in a state not listed under the recall (vehicle purchased used in Pennsylvania in 2017). As a result of this part failing, my brake lights remained engaged permanently, and the car's engine power would increase and decrease rapidly (presumably because it thought I kept hitting the breaks). At time of writing I still have the broken pieces of the original part. I plan to take the vehicle into service within the week. There are no warning lights when this occurs since everything I'm the car is technically "operating correctly" - it just thinks the breaks are engaged constantly, and so has erratic behavior. The original recall lists high humidity as a cause, which Pennsylvania definitely has. I keep my vehicle outside 24/7, so it has definitely been part of many temperature swings.

Door lock not secure. It has happened a few times, usually on the highway, where the passenger side door has opened slightly while driving, causing the opened door light to come on. The door is visibly cracked opened, but it is still locked.

The steering gear including contour module went out. I was backing out and couldn’t turn my wheel my sisters boyfriend had to drive it home on a curvy road with no power steering. I have a local mechanic looking at it but they said the part is on back order which means this must happen a lot. They finally got the part and now are saying it won’t program so are needing to order another part. When I turned the car on to leave my destination it said service powersteering system and abs, but before that there were no warnings. I unplugged the battery for 30 minutes to rest the car and everything worked fine for another 1, then driving down the road it went out again.

The contact owns a 2015 Ford Mustang. The contact stated that while driving at an undisclosed speed and attempting to accelerate, upon the transmission shifting into 4th gear, the tachometer rose 3,000 RPM, after which the vehicle lost motive power and the transmission was unable to shift above 4th gear. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the clutch. The vehicle was not repaired. The manufacturer was notified of the failure but referred the contact to the NHTSA hotline for assistance. The failure mileage was 10,000.

Third tail light and rear tail lights remained illuminated after the car was turned off. Driver discovered the brake light switch (rubber/plastic piece) had crumbled into the floor board preventing the tail lights from turning off, thus, becoming a hazard to other motorists on the road as the tail lights remained illuminated even while driving. While the vehicle was being driven, the driver could not accelerate to the appropriate speeds as the car was "thinking" the brakes were being applied and could only approximately drive at 40-50 MPH. The vehicle has been inspected and the above information was confirmed as the issue. No other warnings/messages occurred prior to the piece breaking.

The weld that holds the clutch pedal broke causing the clutch pedal to not engage properly. Which led to not being able to shift gears which left the car unable to drive and left the stranded on the side of the road. The weld that hold the clutch pedal in place is insufficient and weak. While researching this issue I found many instances where this has happened to other drivers.

The contact owns a 2015 Ford Mustang. The contact stated that upon attempting to start the vehicle, the vehicle failed to start. The "Depress the clutch to start the vehicle" and check engine warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 101,000.

Wire under passenger sear for heated seats has burning smell. Wire was replaced but happens again. Will need to replace entire plug.

The contact owns a 2015 Ford Mustang. The contact stated that while driving at various speeds and making a turn, the steering wheel was stiff, and the vehicle intermittently experienced a loss of power steering assist. No warning light was illuminated. The contact restarted the vehicle to correct the failure. The vehicle was taken to the dealer, where it was diagnosed that the rack and pinion needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 40,000.

After 5 visits to a Ford dealer, rough idling issue finally discovered and fixed on 5/4/2023. All 4 VCT solenoids were found to have malfunctioned. Issue began 06/2020 and involved car rough idling at stops or stop and go traffic. No codes were shown on dash. During episodes, car might shut off. It would turn on if car restarted again. Vehicle first seen at Ford dealer on 7/3/2020. No issue found. Follow-on visits on 3/11/2021, 10/25/2022, and 3/22/2023 brought no answers to issue. Car left at dealers for 2-5 days at a time.

2015 mustang ecoboost premium with performance package. Coolant leaked into the engine oil, causing damage to the engine. Now the engine may have to be rebuilt or replaced.

It stolen

The contact owns a 2015 Ford Mustang. The contact stated that the local dealer had previously marked the NHTSA Campaign Number: 22V082000 (Back Over Prevention) recall repair as completed because no failure was found upon inspection of the vehicle. The contact stated that the trunk later failed to open, and the trunk emergency release mechanism was inoperable. The vehicle was taken to another dealer, where it was diagnosed that the deck lid wiring harness had failed, and the failure was related to NHTSA Campaign Number: 22V082000 (Back Over Prevention). The dealer sent a diagnostic report to the manufacturer; however, the manufacturer declined to cover the repair. The manufacturer informed the dealer that another dealer had already marked the recall as complete upon inspection of the vehicle. The vehicle was not repaired. The failure mileage was approximately 15,600.

The contact owns a 2015 Ford Mustang. The contact stated while driving at various speeds and while the vehicle was parked, the windows went up and down, the doors unlocked, the back-over prevention camera engaged, the trunk opened, and the exterior lights engaged independently. Additionally, the check engine warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed that the harness that extended from the rear to the front of the vehicle had failed. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 22V082000 (Back Over Prevention) however, the failure persisted. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage approximately 85,000.

Back up camera goes in and out, fuel pump started making bad sounds a few month after buying it like screeching sounds got the car around 39000

The contact owns a 2015 Ford Mustang. The contact stated while operating the vehicle, the back-over prevention camera displayed a distorted screen. The vehicle was taken to the local dealer and serviced under NHTSA Campaign Number: 22V082000 (Back Over Prevention). After retrieving the vehicle, the failure was still present. The contact stated that the back-over prevention camera display became inoperable and only a blank screen was displayed. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 96,000.

The contact owns a 2015 Ford Mustang. The contact stated while driving 50 MPH, the vehicle began to vibrate violently. The contact stated that the failure was intermittent at first but had since occurred while driving 50 MPH or faster. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed failures with the center support bearing and drive shaft assembly. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA Campaign Number: 17V408000 (Power Train) but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 99,000.

The contact owns a 2015 Ford Mustang. The vehicle was taken to the local dealer to be repaired under NHTSA Campaign Number: 22V082000 (Back Over Prevention). The vehicle was repaired. The contact stated that while reversing, the camera became inoperable. The image was not available, and the check with the dealer message was displayed. The vehicle was taken back to the local dealer but was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 73,000.

The fuel tanked cracked. It was no longer able to hold vacuum. The engine light came on and stayed on. The 2.3L mustang had a similar issue due to heat. It was inspected and fix at a local repair shop.

The welds on the top of the clutch pedal at the pivot point were insufficient from the factory and failed. I was having issues operating the clutch and after doing some research found that this is a common issue and was never covered under any factory warranty. I did not have this inspected at a dealer because I knew it would not be covered. I was able to remove the pedal assembly and repair it and added additional welds myself. I think this is a huge safety concern due to the possibility of the clutch pedal cracking completely and coming loose, which could cause the vehicle to unexpectedly engage the clutch and run someone over or cause a collision. I have photos of the damaged components. It took me a total of 8 hours to complete the repairs. I am also concerned about the quality of the steel used to construct the pedal as it may be too brittle. The OEM should re-design this part and update their manufacturing & welding proceedures.

The contact owns a 2015 Ford Mustang. The contact stated that he received the recall notification for NHTSA Campaign Number: 22V082000 (Back Over Prevention) four years ago. The contact stated that every time he scheduled the appointment to have the recall repair completed at the dealer, it was informed that the part was not available to complete the repair. The contact stated that while he was driving in reverse mode, he noticed the back-over prevention camera was inoperable. The vehicle was taken to the dealer, where the contact was informed again that the part was on backorder. The vehicle was not repaired. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the failure but confirmed that parts were not yet available. The manufacturer was not made aware of the failure. The failure mileage was approximately 1,000. Parts distribution disconnect

The little rubber pad that it attached to the brake pedal disintegrated. Without that pad the vehicle goes into limp mode and won’t drive over 40. Don’t know why the brake switch is connected to other electronics in the vehicle that would make it go into limp mode. Very unsafe while driving on the highway.

The contact owns a 2015 Ford Mustang. The contact stated that while driving at unknown speeds, the valve cover was engine oil leaking onto the exhaust manifold. There was smoke coming from underneath the hood. There were no warning lights illuminated. The vehicle was taken to an independent mechanic and four new head gasket holes were drilled, and bolts were added. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was 55,000.

The contact owns a 2015 Ford Mustang. The contact stated that the body seal under the passenger’s side front windshield had pinholes. There was water entering the vehicle onto the floorboard. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 65,000.

Backup camera recall repair failed to connect the problem. Backup camera still not functioning.

The contact owns a 2015 Ford Mustang. The contact stated that while driving at an undisclosed speed, the vehicle stalled in the middle of the highway. The vehicle was towed to the dealer, where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired; however, the contact stated that the engine had been replaced six times since the vehicle was purchased in 2018. The manufacturer was made aware of the failure and the contact was informed that the engine would be replaced; however, the vehicle would not be replaced. The failure mileage was approximately 82,000.

The brake pedal stop bumper has fallen off and causing the exact issues in safety recall notice 22S02; NHTSA recall 22V011. This vin and others should also be added to this recall. Pictured item was located on the floors.

In October 2021 I attended my sisters funeral in Dallas Tx while in the parking lot I went to back up and backed into my Sons vehicle. No insurance claim was filed but I did pay out of pocket for the damage which was 2800.00. At the time I was unaware of the safety recall. My car still has no reverse camera clock or temperature reading and tpms system is failing as well. Last October I took the car to Johnston Ford in New Boston Texas. They kept the car for two and a half hours and fixed nothing. I repeatedly call back and always say they will return my call but to no avail. Please help I am lost without my reverse camera

The plastic break switch pad broke when I was driving on the highway. I lost engine power and RPMs were erratic. Brake lights would not turn off even when brakes were not applied. I could not excellorate normally or maintain speed. Upon examination the pad was brittle and yellowing. There is already a safety recall for this part but only in certain states that does not include Arizona.

FORD LETTER DATED JUNE 2023, IMPORTANT SAFETY RECALL. 22S06, REAR VIEW CAMERA AND WIRING. PARTS AVAILABLE. PARTS ORDERED BY VIN ON JAN 31, 202, BY- SERVICE ADVISOR. WORK ORDER 29144. PARTS DEPARTMENT JULY 13, 2023 STATED PARTS WERE NOT ORDERED. FORD MOTOR CO. REPRESENTAIVE JULY 13, 2023 STATED GO TO ANOTHER FORD DEALER. DOESN'T FORD MOTOR CO. ISSUE A LICSENCE TO THAT DEALER TO COMPLY WITH FORD MOTOR CO., RULES? SAME THING HAPPEN, TO GO ANOTHER DEALER FOR A NOCK IN THE MUSTANG V-6 ENGINE.

The REAR VIEW CAMARA has STOPPED WOKING COMPLETELY rendering it UNSAFE when backing up.

Tried to go through dealer they refused to fix

What component or system failed or malfunctioned, and is it available for inspection upon request? The break pedal stop pad broke into small pieces while I was driving today. My car suddenly would not go above 40 and while going up a hill I couldn’t go faster than 20. When I finally got home I realized that my break lights would not turn off. I did google and it said to look on the floor board and see if there was anything on the floor. The pieces I found were identified as the break pedal stop pad. Yes it is available for inspection and I took pictures of the broken bits from the floorboard. How was your safety or the safety of others put at risk? My car suddenly was unable to go the speed limit in 6 o’clock traffic putting me as well as those driving behind me in danger of a collision and physical harm. Has the problem been reproduced or confirmed by a dealer or independent service center? No Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? A message did pop up that said uphill break assist unavailable within 5 minutes of me getting in the vehicle. I had no previous issues or warnings before this incident.

Passenger door suddenly opens at highway speed (over 70 mph), requiring very dangerous manoeuvres to stop and close it again. This happened 6 times in 4 hours of travel.

The evap core is known be a faulty part on these cars. It makes it unsafe to drive due to visibility from fogged up windows without it working properly.

Ford Motor Co. LTR. Dated March & October 2022. Safety Recall 22V082. Several times check with the Huntington Beach, CA. Ford Dealer. Last time in Jan. 2023. They order parts (kit) by VN number. Three different Service Adviser's stated they will phone me. Nothing Yet. Recall Notice 22R01, Brake pad was replaced. Works find.

The rear view camera randomly became unavailable after starting the car. Restarting the car did the fix it. In my online research, it is said that the cause is a faulty wiring harness that Ford used between 2014 and 2017, which would affect my car (2015).

Has two Recalls on my car