2017 Ford Fusion complaints

Coolant leaking into engine. Engine block required entire replacement. Check engine light flashing causing me to contact Ford Dealer/Service. This was December 4, 2023.

The contact owns a 2017 Ford Fusion. The contact stated while driving 55 MPH, there was an abnormal sound coming from the engine compartment, after which the vehicle inadvertently lost motive power. The contact was able to coast to the shoulder of the roadway, where the vehicle failed to restart. No warning lights were illuminated. The vehicle was towed to the dealer, who determined that coolant had leaked into the engine, resulting in engine damage. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, and a case was opened. The failure mileage was unknown.

The contact owns a 2017 Ford Fusion. The contact stated that while parking the vehicle, the vehicle stalled. Upon restarting the vehicle, the vehicle failed to move forward or reverse. The system default warning light was displayed. The contact called the local dealer and was informed that the vehicle was not covered under the recall. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline. The failure mileage was approximately 77,432.

I went to my dealership because of a check engine light. After many hours of searching, I was told that a coolant leak had been found. I was informed that the head gasket was damaged and causing a leak into the engine. The cheapest repair would cost nearly $8000. The extended warranty that I purchased for the car has expired. Searching Google, I see that Ford is aware of the problem, and has known about it for some time. Ford should not be able to get away with this.

The contact owns a 2017 Ford Fusion. The contact stated while accelerating from a complete stop, the vehicle shuddered and was sluggish. The contact stated that the failure recurred while driving and while reversing. The vehicle was taken to an independent mechanic, where the spark plugs were replaced; however, the failure recurred while driving at various speeds. The contact stated that the vehicle failed to exceed 30 MPH on one occasion. The check engine warning light was illuminated. The contact veered to the side of the road. The vehicle was towed to another independent mechanic, where it diagnosed that there was coolant intrusion in cylinder #3, and the engine needed to be replaced. The contact was referred to the dealer for repair. The vehicle was towed to the dealer, where the same assessment was made. The vehicle was not repaired. The contact related the failure to Ford Campaign Number: 21N12 and TSB Number: 22-2134; however, the dealer informed the contact that the vehicle was not covered. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.

The contact owns a 2017 Ford Fusion. The contact stated that while starting the vehicle, there was blue smoke coming from the exhaust pipe. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed that there was coolant intrusion into the engine and determined that the short block needed to be replaced. The vehicle was then taken to the dealer to be repaired under NHTSA Campaign Number: 23V162000 (Service Brakes, Hydraulic) however, the dealer declined to perform Customer Satisfaction Program: 21N12 (Short Block Replacement After Coolant Intrusion). The vehicle was not repaired. The manufacturer was made aware of the failure and a case was opened. The manufacturer informed the contact that Customer Satisfaction Program: 21N12 (Short Block Replacement After Coolant Intrusion) associated with the VIN had expired. The failure mileage was approximately 130,000.

The contact owns a 2017 Ford Fusion. The contact stated that while the vehicle was idling at a red light, the vehicle lost motive power and shut off. After several minutes the vehicle restarted, and the contact was able to continue driving. The contact stated that coolant was leaking underneath the front end of the vehicle, and there was white smoke coming from the exhaust during the initial startup. The coolant level was low. The check engine warning light was illuminated. The contact believed that the failure was related to NHTSA ID Number: 10210392 (Engine and Engine Cooling, Equipment). The vehicle was taken to an auto body shop to be diagnosed. The contact was informed of a misfire in cylinder #2. The contact's father had changed the spark plugs. The vehicle was then taken to the dealer and the contact was informed that the air intake was missing from the vehicle. The contact was informed that the air intake needed to be replaced. The vehicle had not been repaired. The manufacturer was made aware of the failure, and it was confirmed that VIN was included in the NHTSA ID Number: 10210392 (Engine and Engine Cooling, Equipment) however, it was no longer covered due to exceeding the mileage indicated in the TSB. The contact was referred to the NHTSA Hotline. The failure mileage was 86,683.

The contact owns a 2017 Ford Fusion. The contact stated while driving at an undisclosed speed, the contact observed white smoke coming from the exhaust, after which the vehicle inadvertently lost motive power. The contact was able to coast to the shoulder of the roadway, where the vehicle was able to be restarted. No warning lights were illuminated. The vehicle was taken to the dealer, who determined that coolant intrusion in cylinder #2 had damaged the engine, and the engine needed to be replaced. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, who again determined that coolant intrusion in cylinder #2 had damaged the engine however, the vehicle was not repaired. The manufacturer was notified of the failure, and a case was opened. The failure mileage was 60,000.

My 2017 Ford Fusion has a coolant issue. Per TSB 19-2139. Ford has a known issue in the cylinder walls and had a program available until November 2022. Sadly this program ended and they still have issues. It has been verified at a third party mechanic and Ford doesn't want to assist in this issue.

L/S Brake Hose Rear Replacement needed. Brake fluid leak rear caliper and brake hose and line rear flexible hose is split and leaking. Only Front brake hose was recalled when all brake all lines need to be replaced.

Hesitation, lack of power, jerking on acceleration. If felt like an ignition misfire and the engine codes suggested multiple misfires. A power balance test was performed and verified there is a misfire on cylinder 2. The spark plug from 2 was swapped with cylinder 1 and the misfire was in cylinder 1. The spark plugs were replaced November, 2023. The plugs look contaminated-seems to be with engine coolant due to a head gasket failure. The coolant reservoir was empty indicating a coolant leak. They then introduced air into cylinder 2 and the coolant rose inside the coolant reservoir. The gasket is failing between the cylinder and one or more of the water passages beside the cylinder. Ford has since updated their engine design to correct this concern so they knew of the issues. There is a current recall on the 1.5L engine however, not the 2.0L. There are multiple class action suits against Ford for this issue. A new engine is needed. This is a 2017 with 85K miles. A new engine should definitely not be required. When researching this issue, there are multiple safety concerns including engine fire. I spoke to Ford's customer service and they were no help whatsoever.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic and diagnosed with catalytic converter failure. The vehicle was repaired, but the failure reoccurred. The vehicle was taken to the dealer, who determined that coolant intrusion had damaged the engine, and the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure but did not assist. The failure mileage was 113,000.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated on the instrument panel. The vehicle was taken to the dealer, who diagnosed a failure with the spark plugs. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, and it was determined that there was a misfire in cylinder #3 due to low compression. The vehicle was not repaired. After investigating the failure, the contact related the failure to Technical Service Bulletin: 19-2243. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 112,000.

On [XXX], I entered onto [XXX] from Sparks, Nevada eastbound when a check engine light and oil overheat warning came on. I limped the car to the nearest exit [(XXX)]. I had my grandson with me and he was scared. I checked my coolant level and realized that it was dry. I put coolant to the max line of the reserve tank and drove 25 miles to Carson City. When I took it into the dealership at Capital Ford on December 26, 2023, their service manager said this year had a poor design of the engine (2.0L) which led to coolant intrusion into the cylinders. Two days later, they confirmed. My complaint is the FORD manufacturer knew of this issue and had posted several TSBs, but has only issued a recall the 1.5 L engine. I'm now told that since my car is 1600 miles out of warranty, too bad. I believe the FORD manufacturer should replace my engine for free, knowing it failed as a direct result of their poor engineering design. I purchased the car in July 2020 with 26,350 miles and bought the extended warranty. I was never made aware of the existing issues with the coolant leaking into the valves. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2017 Ford Fusion. The contact stated that while driving at various speeds, the vehicle lost motive power and stalled. The contact waited for a while and then made several attempts to restart the vehicle. The check engine warning light was illuminated. The failure occurred frequently and had become more persistent over time. The vehicle was taken to the dealer to be diagnosed and the contact was informed that the engine had failed due to the intake manifold gasket fracturing the seal, which caused antifreeze to leak into the engine. The vehicle was repaired. The manufacturer was made aware of the failure, and it was confirmed that the VIN was not included in a recall. The manufacturer opened a case and offered to pay a portion of the repair cost. The approximate failure mileage was 45,000.

2017 Ford Fusion 2.0L ecoboost engine is available for inspection. The engine block was designed incorrectly and coolant leaks into the cylinder. There is a risk of fire from the intrusion of coolant in the cylinder. Many other people are having this issue and they did recall the 1.5L engine. They need to on the 2.0L as well. My local mechanic identified the issue and I called the Ford dealer who didn't even need to see it said I need a new engine based off the mechanic's testing. After losing coolant and constantly refilling with no coolant being seen coming from the vehicle, the check engine light comes on. The code listed states that one of the cylinders is misfiring. This is due to coolant in the cylinder. With the risk of fire, Ford needs to put a recall on this issue for the 2.0L ecoboost.

The contact owns a 2017 Ford Fusion. The contact stated while accelerating from a complete stop, the vehicle shuddered and hesitated to respond. There was no warning light illuminated. The contact stated that the failure reoccurred while driving 60 MPH. The contact stated that the failure had been recurring while driving. The vehicle was taken to the dealer several times. The dealer diagnosed the vehicle, but the cause of the failure could not be determined. The contact stated that the failure persisted. The vehicle was taken back to the dealer, where it was diagnosed that the torque converter had failed and needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 17V427000 (Power Train); however, the VIN was not included. The manufacturer was notified of the failure and a case was opened. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 106,000.

Check engine has been off and on for last 500 miles. Regular maintenance. Took to dealership, Codes found of P0303, P0300, and p2196. Found coolant was low and confirmed coolant intrusion into engine. Per dealership either bad head, head gasket, or block and ford recommended replacing engine. Quoted $9000 in repairs to replace engine. Declined repair due to cost. According to NHTSA this is a common issue and should be addressed. Unsafe to drive however repair costs, and now inability to trade in, force driving until no longer can

I was driving my car one day and the power steering fault message popped up on my dash of my car. So I turned around and went home. I turned the car off and then turn the car back on. Then the power steering fault message showed up with other warning messages. So I tried turning the steering wheel and noticed there was no power steering at all. So the next day I had it towed to the Ford dealer to have them look at it and fix the issue. They ended up replacing the rack and pinion and the power steering motor. When I picked the car up I asked the service person if it was a common part that broke on the car and he said it was a common part that broke. I was surprised that they had that specific part in stock when they told me the problem. Also I was not happy that I had to $4,400.00 to fix it. In my mind if it is a common part that breaks then why hasn't been a recall on that part.

******* DELETE VOQ ******* THIS COMPLAINT IS BEING MARKED FOR DELETION BECAUSE IT IS REQUESTED BY THE CONSUMER THAT THEY WISH TO HAVE IT REMOVED. DJR ******* DELETE VOQ *******

The contact owns a 2017 Ford Fusion. The contact stated that while his wife was driving at an undisclosed speed, the temperature gauge began to indicate that the vehicle was overheating, prompting the contact to pull over to the shoulder of the roadway. After a visual inspection of the engine compartment, the contact observed that the coolant reservoir was abnormally low and refilled the reservoir. Within three days of refilling the coolant reservoir, the failure reoccurred, after which the vehicle failed to start. The vehicle was towed to an independent mechanic, who was unable to determine the cause of the failure and advised the contact to take the vehicle to the dealer. The vehicle was not repaired. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. After investigating the failure, the contact related the failure to Technical Service Bulletin: 20-2100. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 74,000.

The contact owns a 2017 Ford Fusion. The contact stated while driving 75 MPH, the vehicle stalled without warning. The contact pulled over to the highway shoulder and the vehicle was initially towed to an independent mechanic. The contact was informed by the mechanic that the engine needed to be taken apart to determine the cause of the failure. The vehicle was then towed to a dealer where the contact was informed that the torque converter and the transmission needed to be repaired. The vehicle was towed for a third time to another independent mechanic where the contact was informed that the flex plate had fractured in five separate places and needed to be repaired also. The manufacturer was not made aware of the issue. The vehicle was not repaired. The failure mileage was approximately 107,510.

The contact owns a 2017 Ford Fusion. The contact stated while starting the vehicle, the check engine warning light illuminated. Additionally, there was white smoke coming from the exhaust pipe. Upon inspection, the contact noticed there was a coolant intrusion into the engine. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 67,000.

The contact owns a 2017 Ford Fusion. The contact stated that while operating the vehicle, the check engine warning light remained illuminated, and the vehicle eventually stalled. The vehicle was towed to an independent mechanic who diagnosed that coolant was present inside the engine. The contact was informed that the engine needed to be replaced. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure, but no assistance was provided. The failure mileage was approximately 70,000.

I was pulling onto the beltway and my car would not shift when I accelerated. Then the engine revved up when I accelerated and the car had no power. It remained in the same gear. Then it wouldn’t move at all. I was able to coast off the highway. Turned the car off and started again. It did the same thing. Staying in the gear and then not accelerating. I find it interesting that other 2017 ford fusion had a previous recall for this. My vin isn’t included on the list

The contact owns a 2017 Ford Fusion. The contact stated while driving at an undisclosed speed, the temperature gauge indicated that the vehicle was overheating, and the contact heard an abnormal sound coming from the engine compartment. The check engine warning light was illuminated. The vehicle was towed to the dealer, and it was determined that the engine block had cracked due to coolant intrusion. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure but did not assist. The failure mileage was 131,000.

The contact owns a 2017 Ford Fusion. The contact stated that after starting the vehicle, the check engine warning light illuminated on the instrument panel. The vehicle was taken to the dealer, who diagnosed a misfire in cylinder #2 caused by coolant intrusion into the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure but did not assist. The failure mileage was 63,000.

1.5 ecoboost catastrophic engine failure. On hi-way lost power. Coolant went into engine cracked block. Known defect, but ford says my car is not covered. But won’t explain why, it checks all the boxes, mfg in Mexico during defective years under mileage and date. Never received notice. Stuck with $7,800 repair. Ford executives will not engage to help.

The contact owns a 2017 Ford Fusion. The vehicle was taken to the local dealer to be repaired under NHTSA Campaign Number: 23V162000 (Service Brakes, Hydraulic) however, the contact was informed by the mechanic that the lug nuts were defective. The lug nuts were replaced. The manufacturer was contacted but no assistance was provided. The failure mileage was approximately 54,042.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed with coolant intrusion into the cylinder, and that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but informed the contact that the vehicle was not covered under warranty. The failure mileage was approximately 62,000.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to coast to the shoulder of the roadway, where the vehicle was able to be restarted, but failed to shift into drive. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who was unable to diagnose the vehicle. The vehicle was then towed to the dealer, who diagnosed a failure with the torque converter. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 17V427000 (Power Train), but the VIN was not included. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 84,000.

The contact owns a 2017 Ford Fusion. The contact stated that the check engine warning light was illuminated. The contact took the vehicle to the dealer who diagnosed that there was a leak in cylinder #3. The vehicle was included in Manufacturer Communication NHTSA ID Number: 10213732 (Engine and Engine Cooling) and had the remedy completed. After the vehicle was repaired, the check engine warning light became illuminated. The contact returned the vehicle to the dealer who confirmed that there was a leak within cylinder #1 and that the repair needed to be performed. The vehicle had not been repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 130,000.

The contact owns a 2017 Ford Fusion. The contact stated that the message that the engine was overheating was displayed on the instrument panel. The vehicle was taken to the dealer where a repair was performed for an unrelated safety failure. The repairs were covered by the insurance company; however, during the inspection by the insurance company, it was discovered that there was coolant intrusion into the engine. As a result, the contact was informed that the engine needed to be replaced. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline. The failure mileage was approximately 117,000.

The contact owns a 2017 Ford Fusion. The contact stated that while the vehicle was parked, the transmission failed to shift into drive(D). The Shift System Fault, Service Required message was displayed. The contact noticed that the shifter cable was detached and reconnected the shifter cable. The transmission was then able to shift into drive(D). The vehicle was taken to the dealer; however, the vehicle was not yet diagnosed or repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 94,000.

I was driving to work when I had to stop at a red light as I hit the accelerator it didn’t move. I continued to press it as I was the first car at a green light suddenly the car jerked forcefully and went. I arrived at work and called my father to look at it and he told me to drive it home which is about 7 minutes away. As I drove the car it began jerking violently and slowing down. It was not safe for me to move off the road immediately causing cars behind me to slam on brakes and swerve around me. When I made it safely to the shoulder the gear shift was working but the pressing the accelerator didn’t really work until it continued jerking. The car had to be towed to my home and to the auto shop to be diagnosed. My transmission slipped due a form of malfunction of the transmission. The mechanic expressed there were no metal shavings in the pan. No warning lights appeared on the dash until after it completely broke and they still flashed on and off or changed each time. No crash occurred, it immediately taken to be diagnosed and has already been fixed. I would like for Ford to do an inspection but I just paid for a transmission so I can’t afford it. I have all the receipts and diagnostic information for the vehicle. I looked into the recalls and noticed the ford fusion 2.0L has an active transmission recall, but the only difference for my vehicle is a 1.5L.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the steering wheel was extremely loose, prompting the contact to pull over to the shoulder of the roadway. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA Campaign Number: 18V167000 (Steering), but the VIN was not included. The failure mileage was 82,000.

The Rotary "Dial Shifter" keeps coming on while the vehicle is turned off as well as making a gear sound saying it's not in park when it is. I have had the vehicle for a month and I've had to jump the car 5 times already as it will come on and stay on. I looked it up and some fushions were recalled for it with the issue of that and the cd player and rear speakers making noise. Trying to see if another recall can be issued on more of the fusions.

Approx 2 weeks ago I had a check engine light. The light indicated a cylinder 3 misfire. I then had an engine overheat with the check engine light. The mechanic said engine coolant was leaking into cylinder #3. He said the only repair was a new engine. I called multiple Ford dealers and there were aware of a technical bulliten on issue and said my vehicle was out of warrenty and that nothing could be done outside of a new engine.

2017 Ford Fusion 2.0L EcoBoost with pin hole in Block. Technical service Bulletin 19-2346 Dec. 19 2019 Block has pin Hole in causing coolant to leak into #2 Cylinder. Yes it is Available for Inspection Safety Risk is it could Malfunction in cold weather and create no heat for driver/passengers Yes it has. Been to dealer. Contacted Ford and they said to file Complaint First sign was slight engine miss started around 107,000 miles. Second sign Engine light came on. Brought to Independent dealer and he informed me what the reason was ( cracked Block ). Brought to local Ford dealership and they also confirmed reason (cracked Block ). Researched Ford Bulletins and found Ford realized this Engine Block had a defect back in 2019 when it still would of been under Warranty. Ford Blocks are a Major part and Very expensive to replace. Ford Motors should own up and Repair as they new this before Warranty Expired.

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the engine and had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and assisted with 40% of the cost of the repair. The failure mileage was approximately 63,000. The VIN was unavailable.

My 2017 ford fusion alerted to me that it was overheating, I immediately checked my fluids and noticed my coolant was empty so I refilled it. I assumed that when I recently had my car serviced they somehow forgot to refill my coolant when flushing/replacing me fluids. The next week I went to leave for work one morning and my car wouldn't start, had the battery checked and it was fine, replaced the started and still wouldn't crank. Then I had my fusion towed to a local mechanic who wasn't able to find the issue since they didn't do internal engine repairs, so paid that shop and had it towed to the dealership where I purchased the fusion and a couple of weeks later they tell me my pistons won't hold pressure and I need a new engine (8-10k) with no explanation as to what caused this. My fusion was purchased with 3 miles on it and currently has less than 49k on it. I have always taken very good care of my vehicle, but am now told that my warranty was 5 years from manufacturer date, not purchase date, leaving me with very little options. This issue needs to be addressed asap.

Shift System Fault: transmission shifter cable bushing wore out, cap fell off, shifter cable got detached, so I cannot shift the car out of Park. I have a 2017 Ford Fusion and it was not included in the recall, even though this Shift System Fault problem is the same problem that the Ford Fusions included in the recall are having.

The contact owns a 2017 Ford Fusion. The contact stated while driving approximately 40 MPH, the vehicle lost motive power. The contact that while the vehicle was started, the check engine warning light illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the engine needed to be replaced due to coolant intrusion into the cylinder. Additionally, there were pieces of the cam shaft in the oil pan. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 69,000.

Car started rough and engine light came on. Coolant low. Took car to Ford dealer service department and was told the problem was coolant intrusion. Was told not to drive it as eventually the car would overheat and engine block would crack. Only fix is to get a new engine.

The contact owns a 2017 Ford Fusion. The contact stated while driving at various speeds, the vehicle jerked. Additionally, the contact stated that the vehicle overheated while driving and while idling. The contact stated that the vehicle was experiencing abnormal coolant consumption. The contact had been adding coolant to the vehicle after 5 miles. The contact stated that the failure was persistent. The check engine warning light was illuminated. The vehicle was taken to the dealer but was not diagnosed nor repaired. The dealer informed the contact that they could not repair the vehicle under Ford Campaign Number: 21N12 because the vehicle was not covered. The manufacturer was notified of the failure and informed the contact the VIN was not included. The failure mileage was approximately 74,900.

Engine has been smoking excessively. Diagnosed at Fulton Ford as needing an engine replacement due to coolant leaking in to cylinder. Discussed with Ford twice and they will not consider it under the recall that is effecting numerous other engines of this size.

The contact owns a 2017 Ford Fusion. The contact stated that while attempting to start the vehicle, the vehicle started to shake. The contact allowed the vehicle to idle for one minute before driving. The battery and the check engine warning lights illuminated. The contact stated while driving at an undisclosed speed, there was white smoke coming from the exhaust. Additionally, the contact stated that the vehicle currently failed to start. The contact used a code reader to diagnose the vehicle where an undisclosed code indicating that the failure was engine related. The vehicle was taken to the dealer where it was diagnosed that coolant had leaked into the engine and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was advised to contact the NHTSA Hotline. The failure mileage was approximately 57,000.

The contact owns a 2017 Ford Fusion. The contact stated that after reversing and shifting back into drive, the vehicle failed to move or respond as needed. The contact stated that the “Shift System Fault” warning light was illuminated. The vehicle had not been diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 60,000.

My 2017 Ford Fusion with 77,000 miles was running poorly. I noticed coolant reservoir was empty with no visible leaks. Took it to a Ford dealership and was told coolant was leaking into cylinders. I was told to fix the car they would have to replace the engine. Had I not noticed the coolant issue and the engine died while driving in highway traffic, my safety, as well as the safety of others would have been at risk.

The contact owns a 2017 Ford Fusion. The contact stated while reversing out of her driveway at approximately 3 MPH, the transmission slipped out of reverse(R) and shifted into neutral(N). The contact stated that an unknown warning light was illuminated. The contact stated that the failure had also occurred while in drive(D) and had become a recurring failure. The contact researched online and related the failure to NHTSA Campaign Number: 22V413000 (Power Train). The contact had not taken the vehicle to a local dealer or independent mechanic; however, she had watched videos online on how to replace the damaged shifter cable bushing. The vehicle was repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 115,000.