2019 Ford Flex complaints

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while reversing, the rearview camera displayed a blank image. The message "Camera Not Available" was displayed. The dealer was made aware of the failure but confirmed that parts were not yet available. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 68,000. VIN tool confirms parts not available.

I am submitting a formal complaint regarding multiple premature and potentially safety-related failures on my 2019 Ford Flex, purchased new on 11/25/2019. These include: ⚠️ 1. Rear Suspension / Rear Toe Link Concern Although my vehicle is not included in Ford’s rear toe link recall (20S62), it is experiencing the same symptoms: Rear-end instability and drifting Uneven or premature rear tire wear Clunking or loose feeling from the rear suspension I have an appointment scheduled for August 6, 2025 to inspect the rear toe bar links, as I suspect they are defective or misaligned — the exact condition the recall addresses. 💧 2. Water Pump Failure The engine water pump failed before 100,000 miles, requiring a full replacement. This is a known issue in several Ford engines, and repair was required out-of-pocket despite the vehicle being well maintained. 🚗 3. Exterior Trim Detachment Multiple exterior trim pieces detached from the vehicle while driving, posing a road hazard to myself and others. These parts did not appear to be securely fastened from the factory. 🛞 4. Premature Tire Wear Rear tires wore out far earlier than expected — possibly linked to suspension or alignment issues, including the toe link concerns mentioned above. ⚡ 5. Ongoing Electrical Failures Since August 2022, I have had to return to the dealership multiple times for electrical system issues: 8/3/2022 11/2/2022 2/14/2024 These included battery/electrical drain issues and warning system malfunctions, which affe

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the back-over prevention camera failed to activate or flash an image briefly before displaying the message that the rear camera had failed, followed by the blackout of the screen. The failure first occurred intermittently, but progressively became more frequent, and the backup prevention became inoperable. The dealer was contacted and confirmed that the part was not yet available. The manufacturer was not made aware of the issue. The failure mileage was approximately 46,500. VIN tool confirms parts not available.

Back up camera cuts out/ goes blank at random. This is a safety issue as objects behind the car can not be seen. There currently a recall for this issue, however, only certain months of production. The recall needs to widen to include all 2019 Ford Flex vehicles. No warning prior to notify it is not working until rear camera is activated by placing the car in reverse. Screen is blank.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact stated that the back over prevention camera was occasionally inoperable. The contact stated that it was difficult to operate the vehicle with the back over prevention camera being inoperable, causing visibility issues. There were no warning lights illuminated. The contact received notification of NHTSA Campaign Number 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 30,000. VIN tool confirms parts not available.

When the backup camera first malfunctioned everything was upside down. When I went online I was told to disconnect the battery cable, which seemed to fix it until the next time I put it in reverse. Now it works one out of ten times. It either shows objects upside down or the screen is filled with flashing blue and green or goes completely blank. It then shows "Camera Unavailable," i am very dependent on this camera so I'm anxious to get it repaired.

Re: Ford RECALL Manufacturer Recall Number24S75 NHTSA Recall Number24V951 Recall Status Recall Incomplete, remedy not yet available Summary YOUR VEHICLES REAR-VIEW CAMERA MAY DISPLAY AN INVERTED VIDEO IMAGE, INTERMITTENT OR PERSISTENT LOSS OF IMAGE, ANDOR DISTORTED IMAGE. Safety Risk A REAR-VIEW CAMERA THAT INTERMITTENTLY DISPLAYS AN INVERTED, BLANK, OR DISTORTED IMAGE WHILE IN REVERSE CAN REDUCE OR DISTORT THE DRIVERS VIEW OF WHAT IS BEHIND THE VEHICLE, INCREASING THE RISK OF A CRASH. Remedy DEALERS WILL REPLACE THE REARVIEW CAMERA AS NECESSARY, FREE OF CHARGE. PARTS ARE NOT AVAILABLE. FORD MOTOR COMPANY IS WORKING TO PROVIDE PARTS FOR THIS REPAIR. WHEN THE REMEDY BECOMES AVAILABLE, FORD MOTOR COMPANY WILL NOTIFY YOU VIA MAIL TO SCHEDULE A SERVICE APPOINTMENT WITH YOUR DEALER FOR REPAIRS TO BE COMPLETED FREE OF CHARGE. Manufacturer's Notes IF YOU HAVE ANY QUESTIONS REGARDING THIS RECALL, OR BELIEVE ANY OF THIS INFORMATION IS INACCURATE, PLEASE CONTACT FORD DIRECTLY AT 800-392-3673 OR LINCOLN AT 800-521-4140. *****Been experiencing this issue since 2022; Contacted Bartow Ford in Bartow FL, about this issue, before the recall was issued; they stated they would replace the item for roughly $1k; Ford is saying that they don't have the necessary parts for it, yet Bartow Ford is saying they have a solution for the issue. It's been going on for roughly 10 months + since they've known about this, and the recall is still in advance notice. Proof that it's been long: [XXX] INFORMATION

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact stated that the rearview camera displayed a distorted image while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. In addition, the screen occasionally turned black. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The contact related the failure to NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the VIN was not included. The failure mileage was approximately 73,286.

Hello, This is my second 2019 Ford Flex Limited my previous vehicle did not have an issue with the rear back up camera. My current one does but it vin# is not on the the list. I went to Ford dealer ship and was told that because of the VIN# its does not qualified for the recall but the backup camera does not work always continuously. It appears the issue meets the criteria of my previous Flex I have picture of the failure.

Coolant Intrusion - Water pump leaked inside the engine, causing engine failure. The engine has to be replaced. This has been a known problem with this model and has been fixed/covered by the warranty.

The contact owns a 2019 Ford Flex. The contact stated that after it had rained, the front driver’s side footwell filled up with water. The vehicle was taken to the dealer where the mechanic discovered that the drain in the sunroof was clogged. The dealer was aware of the failure and repaired the vehicle. The contact recently stated that the failure had returned and the driver’s and passenger’s side footwells were filled with water. The contact also stated that the headliner had become stained and soaked with water. Additionally, the contact stated that there was a mildew odor inside the vehicle due to the failure. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA to report the failure. The vehicle was not repaired. The failure mileage was approximately 95,000.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while in reverse, the rearview camera image failed to display as intended on the screen. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 32,000. VIN tool confirms parts not available.

Rear view back up camera failed. The repair solution is long overdue.

The contact owns a 2019 Ford Flex. The contact stated that while driving 65 MPH, the driver's side B-pillar trim detached from the vehicle. The vehicle was not diagnosed or repaired. The contact stated that on another occasion, the passenger’s side B-pillar trim became loosened. The contact removed the passenger side B-pillar trim due to safety concerns. The vehicle was not diagnosed or repaired after the most recent failure. The contact related the failure to TSB: 202427. However, the part to do the repair was not yet available. The manufacturer was not made aware of the issue. The failure mileage was approximately 40,000.

The contact owns a 2019 Ford Flex. The contact stated that while his wife was reversing, the rearview camera image was blue, and the screen displayed an unknown message. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact received notification of NHTSA Campaign Number: 24V951000(Back Over Prevention); however, the part to do the repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 24,000. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact experienced the failure, and the display screen image was distorted or upside down. The contact stated that the failure almost caused vehicle to strike a pedestrian. The cause of the failure was not yet determined. VIN tool confirms parts not available.

Backup camera has not worked for long time. Bartow Ford said part not available for recall but if I want to pay 823, they have the part. Without a backup camera it is like backing up a whale blindfolded.

The contact owns a 2019 Ford Flex. The contact stated while reversing, the back over prevention camera failed to display a rear-view image, compromising the back over prevention system. The contact stated that the message "Rear-view camera unavailable" was displayed. The contact stated that the vehicle returned to normal functionality, but the failure became a regular occurrence. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V951000 (Back Over Prevention); but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 105,000.

On 6/4/2025, the driver side front door B-pillar trim piece separated from the vehicle. The tape that joins the trim piece to the door sheet metal completely sheared. The adhesive is still fine but the form separated. The part is connected only to the door through the wire hardness of the keyless entry. TSB 20-2427 stated the issue is "loose". But the actual issue is a flying part with a connecting string.

The contact owns a 2019 Ford Flex. The contact stated that while attempting to reverse out of a parking spot, the rearview camera image displayed on the screen was displayed upside down. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact was informed that the VIN was not under recall. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 66,000.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the rear-view camera had experienced intermittent failures, with the image frozen or distorted. The failure mileage was approximately 74,000. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact stated while attempting to park the vehicle, the rearview camera became inoperable. The contact stated that the rearview camera image was blank. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The vehicle was towed to the dealer, where it was diagnosed that the rearview camera had failed and needed to be replaced. The dealer confirmed that parts were not yet available for the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 52,000. VIN tool confirms parts not available.

The black glossy plastic applique on the Driver's Door Window Frame (also containing the Keyless Entry Keypad) blew off on the Expressway at approximately 70 MPH. While the wire harness retained the lower portion of the applique, the applique cracked from the force of the separation, for which the bottom third of the applique hung from the harness whereby the upper two-thirds of the applique became a projectile and flew onto the expressway. After sharing this with a friend (also owning a 2019 Ford Flex), he said his came off last year. Upon further studying this matter, it appears that in Ford's wisdom they only used small strips of double-sided tape to retain this; for which there are many reports of this same failure mode: [XXX] In their infinite wisdom, Ford now only sell the Applique Panel with the Keypad (Ford Part Number BA8Z7420555AC ), rendering it at a MSRP of $228.83 just for the replacement part. The Ford Parts Counter Person said they sell a lot of these, due to the poor design and retention. As this is a hazard to others on the road (e.g. potentially becoming a projectile) Ford should be forced to Recall this defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Rear Camera intermeitently works or completely fails. Was backing out of a parking space and could not see and a car speed by the back up warning did beep and saved the day - if my camera had been working I would have seen the on coming car a little bit sooner. it's been months since the recall was issued when will a remedy be available? this should not take this long for Ford to remedy?

The vehicle has a panoramic roof with each of the three windows having a roller sunshade. Two of three roller sun shades have failed or are not working causing excessive glare and heat in the vehicle.

UNKNOWN. The hands free function of the audio system suddenly stopped working properly. When the blue tooth links up with my phone the volume is so low it can barely be heard and can’t be adjusted up. According to my Google search of the issue it appears to be a common problem for Ford.

The water pump and timing cover gaskets are faulty. The water pump is internal and causes major engine malfunction when it breaks.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall was not yet available. The contact stated that the back-over prevention camera failed to operate as intended and the image was distorted. The contact stated that the failure became more persistent, and the screen would turn blue. The dealer was contacted. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 25,000. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact stated while driving at an undisclosed speed, the vehicle started shaking excessively and the vehicle briefly hesitated. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the water pump, resulting in damages to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 50,000.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the back-over prevention camera image was distorted or was rotated. The contact stated that the failure became more persistent, and the images were displaying up-side-down and with incorrect information on the distance from the camera to objects behind the vehicle. The dealer was contacted. The manufacturer was made aware of the issue and opened a case. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 50,000. VIN tool confirms parts not available.

BACK OVER PREVENTION: SENSING SYSTEM: CAMERA 90% of the time, the rearview camera image is blank or has a distorted image.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. An unknown local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that while reversing, the center display failed to provide an image behind the vehicle, almost causing two crashes. The contact stated that the vehicle was not diagnosed or repaired because parts were not yet available. The failure mileage was unknown. VIN tool confirms parts not available.

My camera (rearview) had been dysfunctional for quite sometime and I could not use it. I finally got it fixed 1/9/25 when I brought my car in for a oil change. I bought a great warranty and only had to pay my deductible of $100. Within a month, I got a recall letter for the same reason with the camera. I called Ford corp office and they told me to get the invoice from Ford and send it with the letter to you for reimbursement. So excited to get me $100.00 back for this. Ford highlighted the part for you since the oil change was on the invoice. Any questions please call me at work at 702-XXX-XXXX. Thank you.

The contact owns a 2019 Ford Flex. The contact stated that while attempting to park the vehicle, the contact became aware that the rearview camera was inoperable. The contact became aware that the rearview camera was not functioning properly, and there was no image displayed. There was no warning light illuminated. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The approximate failure mileage was 104,000.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The contact stated that upon shifting the vehicle into reverse(R), the rear-view camera displayed a distorted image, compromising the back-over prevention system. The contact stated that on a separate occasion, the navigation screen showed a black screen and showed half of an image while displayed. No warning lights were illuminated. The local dealer was contacted. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 30,000. VIN tool confirms part not available.

The contact owns a 2019 Ford Flex. The contact stated while reversing, the rearview camera image was upside-down. The vehicle was taken to the dealer, where the contact was informed that the failure was due to a factory defect, and the contact had to pay out-of-pocket for the rearview camera replacement. The vehicle was not repaired. The contact later received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was unknown. VIN tool confirms parts not available.

Rear camera does not work consistently. Obviously, backing up is a safety issue. The rear-view camera image sometimes is distorted, inverted, or completely blank when the vehicle is in reverse. This has been occurring for several months. I have not had vehicle inspected at a dealer or service center at present. The message I receive on screen states "Camera is Unavailable"

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while reversing, the rearview camera had inverted the image and the image was distorted. There were no warning lights illuminated. The dealer was made aware of the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 97,786. VIN tool confirms parts are not available.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

Backup Camera is inverted and no longer displays guides.

In December of 2024 the backup camera on my 2019 Ford Flex started failing intermittently. Sometimes when I put the vehicle in reverse, I get a blue or black screen instead of the camera view. I have seen other complaints with this same issue.

The rear camera in this vehicle is not functioning properly, and it is a known issue on other models of this year.

The contact owns a 2019 Ford Flex. The contact stated while reversing, the rearview camera image failed to display intermittently. The vehicle was taken to the dealer, where it was diagnosed, and it was determined that the rearview camera had failed and needed to be replaced. The vehicle was repaired. The contact related the failure to NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the VIN was not included. The manufacturer was notified of the failure and a case was opened. The manufacturer advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 74,000.

Rear backup camera stopped working