2014 BMW 328i

Defect. BMW of North America, LLC (BMW) is recalling certain 2014 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive), and 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i, M235i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.

Risk. An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.

Remedy. Dealers will replace the head air bags, free of charge. Owner notification letters were mailed February 12, 2026. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.

Risk. An electrical short increases the risk of a fire.

Remedy. Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.

Risk. An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.

Remedy. The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.

Risk. An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.

Remedy. Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. If the side marker lights do not illuminate, the vehicle may be less visible at night, increasing the risk of a crash.

Remedy. BMW will notify owners, and dealers will upload revised software to correct the issue, free of charge. The recall began on October 7, 2015. Owners may contact BMW customer service at 1-800-525-7417 or by email at [email protected].

Defect. BMW of North America LLC (BMW) is recalling certain model year 2014 228i Coupe, M235i Coupe, 320i, 320xi, 328i, 328xi, 335i, 335xi, ActiveHybrid 3, 328xi Sports Wagon, 428i Coupe, 428xi Coupe, 435i Coupe, 435xi Coupe, 428i Convertible, 428xi Convertible, 435i Convertible, 328xi Gran Turismo, 335xi Gran Turismo, and 2015 428i Gran Coupe, 428xi Gran Coupe, and 435i Gran Coupe vehicles. Improper nickel plating of components within the fuel pump may result in the fuel pump failing.

Risk. If the fuel pump fails, the vehicle may stall without warning, increasing the risk of a crash.

Remedy. BMW will notify owners, and dealers will replace the fuel pump, free of charge. Owners were mailed interim notices on May 28, 2015. The recall began on July 6, 2015. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.

Risk. A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy. BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.

Defect. BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.

Risk. A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy. BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at [email protected].

The contact owned a 2014 BMW 328I. The contact stated while the vehicle was parked, the vehicle stalled after overheating the previous day. The contact stated that an unknown warning light was illuminated. The vehicle was towed to a dealer, where it was diagnosed that the valvetronic system needed to be replaced; while the vehicle remained at the dealer awaiting repairs, the contact was notified that the vehicle had sustained thermal damage over the weekend, caught fire, and burned completely, leaving only the frame. The vehicle was unoccupied during the fire. A police and fire department report was filed. The manufacturer was notified of the failure. The contact was later notified that the VIN was included in NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM). The failure mileage approximately 100,000.

I was driving in the highway at 65MPH, I heard an audible tone. I looked at speedometer and had a message to to press unlock button to switch gears. Then my engine light came on and was steady. My car went into neutral while driving at 65 mph. Thank god I was able to pull to side. I tried to put back into drive or reverse and no response. It did allow me place in park. It would not start. I had it towed to a BMW service center and they said my engine failed internally.. while driving.

So, the N20 2.0L motors are known to have prematurely failing plastic chain guides and a weak hydraulic tensioner, leading to whine, rattles, and potential engine failure. BMW improved the issue in the 2015 or newer models which have more robust timing chain guides and Tensioners. The fix involves replacing the entire timing chain assembly (guides, chain, tensioner) with updated, more durable parts and cleaning the oil pump/pan of debris. Which the 2015 and newer models have this fix. 2014 and older models with the N20 suffer from failing parts due to a design flaw. Since the The BMW N20 engine (2012–early 2015 328i) does suffer from premature timing chain guide failure, leading to oil pump failure and catastrophic engine failure. There should be a recall with these older models. And there should be a fix for them. BMW design this motor and the only remedy the issue in the newer models 2015 or newer. So anyone that doesn't have a 2015. Their N20 is basically a ticking time bomb.

Vehicle is under Recall 24V-608 for a fire risk. The vehicle has suffered the exact failure described (Overheating, Limp Mode, and Smoke/Thermal Event). Dealership (BMW of Pleasant Grove Utah) is refusing to replace the failed water pump, offering only a 'protective shield' which does not fix the current failure. This is a failure to provide a free and effective remedy for a known safety defect. A code was discovered when the senior advisor at this location ran the scanner, and displayed a "coolant pump switch-off due to locking" which the senior advisor tried to deflect as a physical object blocking the pump or some other mysterious issue. The issue was confirmed at a reputable maintenance shop earlier in the day before towing to BMW dealership. The senior advisor at BMW of Pleasant Grove is attempting to put me back in the road in a high safety risk vehicle.

The contact owns a 2014 BMW 328I. The contact stated that while attempting to register the vehicle in the State of California, the contact was made aware that the VIN was included in NHTSA Campaign Number: 24V608000(Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The dealer informed the contact that the vehicle could not be registered until the recall had been serviced. The manufacturer was made aware of the issue and confirmed that the part was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure.

Thermostat was a recall back then, brought it to the dealer they fixed it and now it has come back, i brought it to a mechanic to fix it, and it came back again one more time. thermostat is staying stuck open. safety recall with emissions

I went to Lakeland bmw, for my recall, they only put a shield up for the recall instead of changing out my water pump which was draining my battery. Now they are trying to charge me for a whole water pump installation even after I informed them that it was supposed to be changed out when I came in for a the recall due too it causing a battery drain.

The water pump is draining my battery, the bmw dealership said they fixed the recall but it has not been fixed. They told me I needed a new battery which was replaced & now it’s back at the shop for a dead battery again.

Mid-mounted Dash/Display Screen has Delaminated, rendering “rear backup camera display” unusable. Delaminating has progressed over time, rendering screen virtually unusable. Since the camera display is unusable, there is immediate danger that the driver might not see an object immediately behind the vehicle, such as a child, and back into/over, causing injury or death. Note: while watching a YouTube video of ANOTHER BMW vehicle, the same phenomenon, mid-mounted (a BMW i8) display delaminated, was shown, meaning this is NOT unique to my vehicle.

Safety Concern Regarding Left Rear Brake and Turn Light Malfunction in a BMW 328i I want to outline a significant safety concern related to the electrical system. specifically involving the left rear brake and turn signal lights. For several months, intermittent warnings indicated a malfunction in these lights. On New Years, the warnings ceased to be intermittent, and the lights failed completely. Upon inspection, it was discovered that the ground pin within the wiring harness had melted off the tail light connector and fused into the harness itself. The melting of a wiring pin is a critical issue that indicates an electrical fault, likely due to excessive current or resistance, and presents a serious safety risk. The fact that a core safety feature of the vehicle—the brake and turn lights—failed completely due to this issue is a significant concern. This type of malfunction can lead to a rear-end collision, as drivers behind the vehicle would not be properly alerted to braking or turning maneuvers. This situation is not merely an inconvenience but a potential public health and safety hazard. The failure of vehicle safety components, particularly those responsible for signaling, directly increases the risk of motor vehicle accidents, which are a leading cause of injury and death. NHTSA is responsible for ensuring vehicle safety, and the failure of vehicle lighting systems due to a manufacturing or design defect is a violation of these standards and a common factor in accident

The contact owns a 2014 BMW 328I. The contact stated that while his son was driving at an undisclosed speed, the engine overheated. An alarm sound was coming from the vehicle. An unknown warning light was illuminated, and there was smoke coming from under the hood. The contact's son was able to pull over to the side of the road. The vehicle was towed to an independent mechanic, where it was diagnosed that the water pump had failed and needed to be replaced. The vehicle was repaired. The mechanic called the BMW dealer to order the parts and asked if there was a recall for the water pump, and was informed that there was no recall for the water pump issued by BMW. Upon further investigation, the contact found a recall on the NHTSA.gov website issued by BMW for the water pump. The manufacturer was made aware of the failure and confirmed that there was a recall associated with the VIN. The manufacturer informed the contact that to receive a reimbursement, the contact needed to contact a local BMW dealer to verify that the recall repair was completed. The vehicle was taken to the dealer, and the contact was informed that the original water pump was needed to complete the inspection. The contact informed the dealer that he no longer had the original part. Several weeks later, the contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM). The manufacturer denied the claim for reimbursement since the repair was not completed at a

The contact owns a 2014 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

The contact owns a 2014 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2014 BMW 328i. The contact stated that the check engine warning light was previously illuminated. The contact received notification of NHTSA Campaign Number 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. An unknown local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 90,000. Parts distribution disconnect.

The contact owns a 2014 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was unavailable. The dealer was not contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2014 BMW 328i. The contact stated that while coming to a stop, the vehicle lost motive power with the check engine warning light illuminated. The vehicle was towed to an independent mechanic, where it was diagnosed that the fuel pump module had failed and needed to be replaced. The vehicle was not repaired. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The dealer was not contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 126,000. VIN tool confirms parts not available.

The recall for this car part has been made public for 10 months and there is still not a remedy available. Considering the issue potentially being a fire hazard, I find this unacceptable and alarming. Since being notified of the news, I now have white smoke/steam coming out from the hood at times, which worries me as this is one of the possible effects from the recall. A BMW dealership will not take the car in if there is no resolution to this and it would be an out-of-pocket expense. I would understand all recalls take some time but it has been nearly a year and there have been no updates throughout this process.

The contact owns a 2014 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling; Electrical System); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2014 BMW 328I. The contact stated that the air conditioning system was inoperable, and the vehicle was overheating while driving. The contact stated that the failure had increased, and the engine overheated upon starting. Additionally, the contact stated that the vehicle had failed to start and was undrivable. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 87,000. VIN tool confirms parts not available.

Manufacturer has yet to remedy recall. No timeframe for a solution