2012 Mercedes-Benz C300 complaints

2012 Mercedes Benz C300 4-Matic; Failure of rear subframe, significant crack of an important support member; very limited minor corrosion of the other parts of the frame, seems to be a manufacturing quality defect in a very specific part. Vehicle has been inspected by a highly qualified independent mechanic and by the closest manufacture's dealer in Massachusetts. Car cannot be driven because it is unsafe to do so. Both the dealer's service department and the independent repair shop have advised and confirmed this. Limited research online seems to indicate that this problem is well known by Mercedes Benz, and the manufacturer has issued recalls in other countries and has taken some responsibility for this defect. However, in the USA, Mercedes Benz has not issued a recall, to the best of my knowledge. It certainly seems that they should have done so. It is highly likely that many owners with this problem lack the knowledge or experience needed to report this problem to the appropriate authorities. I happen to have an above average knowledge regarding automobiles. I first became aware of this problem in Nov., 2021. The vehicle is available for inspection by your department if you deem appropriate.

The contact owns a 2012 Mercedes -Benz C300. The contact stated that upon inspection of the vehicle, he was informed that corrosion had developed on the subframe. The dealer informed him that the subframe needed to be replaced to prevent a possible severe safety failure. The contact emailed the manufacturer about the failure and received a response informing him that they could not offer any assistance. The manufacturer referred him to the NHTSA for additional assistance. The vehicle had yet to be repaired. The failure mileage was approximately 113,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated that while her granddaughter was driving the vehicle, there was a rattling sound coming from underneath the vehicle. The vehicle was later inspected by an independent mechanic who diagnosed that the rear passenger’s side wheel well had sustained severe rust and corrosion and informed the contact that the vehicle was unsafe to be driven. The vehicle was not yet repaired. The manufacturer and local dealer were not notified of the failure. The VIN was not available. The failure mileage was 115,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving approximately 2 MPH over a speed bump, there was a loud cranking sound coming from the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer and diagnosed with failure to the rear subframe due to severe rust. The vehicle was repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 121,218.

My car smell like a gas leak. I had went to a car shop to have the car to looked at. The mechanic had told me that the fuel filter flange is leaking gas.

So here I am - another "happy" driver with a rotten subframe. Started noticing instability on the highway speeds a few months ago. Cracking noises lately. Since I use this car my very honest mechanic immediately told me that my rear subframe is completely done and I should not be driving the car until it is replaced. He quoted me $4500 (OEM parts + labor), but suggested that I take my car to MB and insist on covering the repair costs as this issue did not seem typical to him at all. I started googling and ended up here. Seems like this is a common issue and sounds like MB will replace the subframe for free in some other countries (cananda and Germany, .The dealer said the repair will cost Over $5000.00 This is a safety issue, A real big one. And the fact it's covered in other countries is so not fair. I own another mercedes and now I feel the cars are not as safe as they used to be. Please let me know what I need to do next

The rear sub frame has rusted out and broken causing the car to veer suddenly to the left during braking. A quick search of the internet reveals that this is a common problem with this car. The dealership has quoted me $4,000 for the repairs.

I was traveling at roughly 55mph when I had to make a sudden deceleration due to another vehicle pulling out in front of me. When I applied the brakes, the car unexpectedly pulled violently to the left nearly causing a head-on collision with an on coming vehicle. After Googling the symptoms/scenario, I found that this can be caused by a rusted and failed rear suspension subframe. The control arms for the rear wheels become detached from the subframe as a result. Based on my research, this seems to be an extremely common occurrence. So much so that Mercedes Canada and Mercedes Germany are replacing the defective subframes free of charge as they’ve concluded the cause to be “inadequate corrosion protection” applied to the inside of the subframe. It seems as though they’re rotting from the inside out. After learning everything about the issue, I pulled my car on to ramps in my garage and was able to confirm that my subframe had indeed failed. This is a serious safety issue which is being addressed elsewhere. During my research I was unable to find a recall or TSB related to this issue, only hundreds of people stating that Mercedes forcing customers to cover the cost to repair this extremely dangerous manufacturing defect.

Rear Subframe Rot- this seems to be a common and known issue with Mercedes’ that should be a recall. Yet Mercedes is charging almost $6000 to get this fixed at the dealer. Plus the parts are on back order for months. This is causing cars to sway when stopping. This is definitely a hazard and should be addressed ASAP!

The rear subframe on my 2012 Mercedes Benz C300 was corroded and broke. This caused the car to lose control and easily could have been been life threatening at high speeds. Mercedes Benz is clearly aware of this issue and knows this is a part defect but has not been willing to do a recall in the US even though they have done so in other countries. The dealership has told me this needs to be repaired as the car can’t be driven, so I am not happy I need to pay $5,000 out of pocket for a part defect Mercedes knows about and refuses to issue a recall even though this problem can cause a fatal accident. There were no warning signs besides hearing thumping sounds and the instability caused by the part defect when it finally failed and broke.

Part number: 207-350-97-02 This is the sub frame part number, during routine maintenance i found a cracked rear sub frame mount. Upon googling, there are hundreds of owners with that same problem. Cars with milage ranging from 40,000-150,0000 with the same issue. Under hard braking the car is unstable. When I called the MB dealer to inquire about the problem they did confirm that the problem is known but is not a safety recall and the repair bill is near $5,000. So Mercedes, confirmed it’s a known issue with a faulty part, confirmed it was a safety issue with the 2008-2012 Mercedes c300 and is not covering it.

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving 70 MPH, there was an abnormally loud sound from the rear of the vehicle. The contact lost control of the vehicle. There was no warning light illuminated. The contact was able to continue normal driving once he regained control of the vehicle. The contact scheduled an appointment with an independent mechanic for the vehicle to be inspected. The contact was informed that the rear subframe had detached from the passenger’s side of the vehicle due to severe corrosion. The dealer was notified of the failure and informed him that there were no recalls related to the failure on his vehicle. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 138,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated that while the vehicle was receiving a routine maintenance, she was informed that the rear sub frame was rusted and had two holes. The vehicle was diagnosed that there was a transmission leak and the rear sub frame needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure but no additional assistance was provided. The failure mileage was approximately 88,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving approximately 65-70 MPH, he heard abnormal clicking sounds coming from the rear of the vehicle. Additionally, the contact stated that while driving and depressing the brake pedal to come to a complete stop, the vehicle swerved while stopping. The vehicle was taken to an independent mechanic where it was diagnosed that the rear driver's side subframe was severely corroded and fractured and needed to be replaced. The dealer was notified of the failure and informed the contact that the vehicle would be repaired at his own expense. The vehicle was not repaired. The manufacturer was notified of the failure but did not provide any assistance. The failure mileage was approximately 75,000.

The rear K frame on Mercedes Benz C300 totaly rusted through and broke apart causing the entire rear of vehicle to rest upon the fuel tank. The failure also caused stress on rear brake lines. The vehicle is 10 years old with 90,000 miles purchased brand new and garaged. Mercedes has performed a recall on Canada vehicles but no USA vehicles. This is total negligence. This is going to cause a fatality. Either a vehicle will catch fire or brake lines will fail and cause an accident. The vehicle is known by the dealers to have this damage/failure. I googled and found numerous cases. Mercedes was not willing to stand by the vehicle and repair. This should be a recall like it is in Canada. I was quoted $5000.00 to repair by Mercedes.

I drove over an object on the highway and noticed my car veering left and wobbly when turning. A week after, it is squealing like a load of piglets in my trunk whenever I go over a bump, then my battery light came on and I took it to the shop and contacted my insurance, who denied my claim saying it was 'wear and tear'.

From the mechanics notes: Four-wheel alignment could not be completed. Attempts to align the rear axle were unsuccessful due to flexing/movement in the rear suspension. A brief road test revealed occasional suspension “clunking” coming from the rear of the vehicle. Close examination of every suspension component mount revealed heavy cracking on the passenger side lower drag link subframe mount (see emailed image). The driver’s side low drag link mount location is also starting to show signs of overstress and rust/flaking. This is a known design defect that has been the subject of a manufacturer’s recall in Canada. Given the substantial safety impact of this design defect/failure, it is expected that a US recall will be forthcoming. Proper repair of this failure involves removing the entire rear axle/subframe assembly and either rebuilding/re enforcing the subframe or replacing it with a new unit and transferring all the suspension components to the new subframe. A current check of subframe availability is showing NLA (no longer available) status from Mercedes wholesale dealers – likely due to recent high demand and inability to satisfy that demand. This supply issue may also be playing a role in Mercedes’ failure to address this high level safety issue with a US based recall campaign. The manufacturer may be ramping up production of this component to address anticipated need – waiting to announce a recall when it has sufficient parts on hand to execute the campaign. It is str

I took my vehicle in for a state inspection and was informed the rear subframe was rusted/rotting and on the verge of detaching. Had this happened while driving, the results could have been catastrophic. The vehicle cannot be driven until this $4K dollar repair is completed. Upon speaking with the mechanic, this is a well known issue within Mercedes. Had I not asked for an alignment, this would have remained undiscovered until it inevitably broke off while driving the vehicle. This is a major safety issue and a safety recall should be issued.

The contact owns a 2012 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, he depressed the brake pedal and the vehicle swerved. Upon inspection, the contact noticed that the rear passenger's side sub-frame was corroded and the stabilizer arm had detached from the sub-frame due to corrosion. The vehicle was taken to an independent mechanic who diagnosed that the sub-frame needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 100,000.

Vehicle was in for state inspection at an authorized inspection station. It failed inspection due to severely rusted and deteriorated rear K-Frame which had to be replaced to pass inspection. This is a major defect I feel caused by manufacture negligence. There were no warnings, messages or any signals indicating a problem. This issue could have severely caused an injury or even death had it not been detected by the mechanic inspector. Mechanic stated to me that he had replaced several of the rear K-Frames in the last year on this make and model.

While driving recently we noticed that the vehicle pulled to one side while braking, and very hard under quick stop tests. Vehicle handling felt extremely dangerous when performing a hard brake test. An inspection was performed, and the service center found a rotted out rear subframe, and cracking around the suspension mounting brackets. After researching this repair, we found this to be a common problem in this and similar model Mercedes-Benz (MB) vehicles of that vintage. I understand that a recall may have been issued in Canada regarding this issue, but not in the U.S. Mercedes-Benz and their service stations have acknowledged this issue is common but they have not taken action to rectify this serious problem, or to compensate owners for the repair costs, which range from $3500 to $6000 depending on where the vehicle is serviced. We are the first owners of this car. It is barely 10 years old, is regularly maintained, and thoroughly washed during the winter months to remove road salt. A well maintained vehicle should not deteriorate this rapidly from rust, especially a Mercedes-Benz. We feel that it is unacceptable for MB to remain unaccountable for this problem.

Rear subframe failure caused me to loose control of vehicle almost resulting in a serious highway accident. Rear driver side stabilizer subframe mount was completely corroded and broken away from the subframe. There is no other significant corrosion on the subframe. MB claim normal corrosion however the pictures tell a different story.

While performing service inspection, technician found REAR SUB FRAME RUSTED AND READY TO BREAK. Told they needed to show me the problem on the lift, as it was a serious SAFETY ISSUE and should be IMMEDIATELY REPLACED. Dealer and service acknowledged that this is a KNOWN and WIDESPREAD PROBLEM in C Class vehicles. Cost to replace quoted at $4200. No warning - thankfully inspection found before I was in a serious accident! Mercedes should issue recall for failed/corroded frame. Not the "safe" vehicle that Mercedes claims. (Car has been dealer serviced regularly, garaged, and 34,000 miles.) Owners shouldn't have to suddenly come up with $4,200 in order to drive their seemingly normal car. DANGEROUS.

Per the dealership in connection with a regular service, the rear subframe rusted out and became structurally weak and was a safety hazard. The problem was confirmed and repaired by an independent repair shop. From Google searches, this issue does not appear to be an uncommon problem. Car is garaged and receives regular underbody washes for road salt.

While driving, engine stopped, could not steer.. Looks like a defective Electronic Ignition Switch or steering lock! It seems to be a common problem on these cars!!! The car would not start. After 8 attempts, I was able to start car but was afraid to drive it. Could have been a disaster.

This is a followup to a previous report. I now have photos and the actual part that was replaced. While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic. Took car to my regular mechanic and it was determined that the welds on the left rear portion of the rear subframe had rusted out from the inside of the subframe, severing the attachment to the left rear wheel control arms. The car had been inspected 6 months earlier and there was no sign of problem. The failure was catastrophic, not gradual. Upon removal, it was also noted that the right mounting bracket was also in the process of rusting through and failing. When the mechanic called the local Mercedes dealer, the service manager was not surprised and proceeded to outline what parts would be needed to carry out the repair. When I contacted the local Mercedes dealer, myself, they said this wasn’t an uncommon problem, but there was not recall or service bulletin on the problem. Was given a rough quote of $5000 to affect the repair. I also contacted Mercedes Benz USA and was told there were no recalls or service bulletins, but they might be able to provide some “Goodwill Assistance” to offset the expected cost if I had it towed to a MB dealer and got a quote from them. Benzworld.org, an owners forum with over 5 million participants world-wide https://www.

The rear subframe rusted through causing mounting point of the torque link to fail. As a result, the car looses control when braking going sideways. Luckily, I discovered it when testing brakes after pad replacement in a safe setting. To my understanding, there are many other W204/W212 cars affected in the US with that issue. Mercedes so far does not want to take responsibility and recall cars for this issue which is a huge concern.

3 signal Signal light comes one saying abs, another SRS MALFUNCTION, also crushed control inoperable. Car will come one as normal next day car comes on no lights not 1 button work turn signals didn’t work then my car fan came on in the engines the also the when they the electric isn’t working i have to manually shift the gear

The contact's wife owns a 2012 Mercedes-Benz C300. The contact stated that upon taking the vehicle to the dealer to be serviced, he was informed that the subframe was severely corroded and could fracture. The manufacturer was notified of the failure and advised the contact that they could not assist as the vehicle was out of warranty. The vehicle was not repaired. The approximate failure mileage was 43,000.

While driving on secondary road at 45 mph, braked for stoplight in 2012 Mercedes C300 4matic. Car veered left, rear swung right, and right front dove downward. Luckily regained control and prevented swerving into oncoming traffic. Took car to my regular mechanic and it was determined that the welds on the left rear portion of the rear subframe had rusted out from the inside of the subframe, severing the attachment to the left rear wheel control arms. The car had been inspected 6 months earlier and there was no sign of problem. The failure was catastrophic, not gradual. When the mechanic called the local Mercedes dealer, the service manager was not surprised and proceeded to outline what parts would be needed to carry out the repair. When I contacted the local Mercedes dealer, myself, they said this wasn’t an uncommon problem, but there was not recall or service bulletin on the problem. Was given a rough quote of $5000 to affect the repair. I also contacted Mercedes Benz USA and was told there were no recalls or service bulletins, but they might be able to provide some “Goodwill Assistance” to offset the expected cost if I had it towed to a MB dealer and got a quote from them. Benzworld.org, an owners forum with over 5 million participants world-wide https://www.benzworld.org/threads/w204-rear-subframes-deterioration.3048088/#post-17965564 has multiple postings about the problem as do other forums including CarProblemZoo.com https://www.carproblemzoo.com/mercedesbenz/c300/susp

The contact owns a 2012 Mercedes-Benz C300. The contact stated her son was driving approximately 60 MPH and noticed that the steering wheel was crooked and vibrating. The driver was manually turning the steering wheel for the vehicle to drive straight. The driver also noticed that while depressing the brake pedal, the rear of the vehicle was shaking going from left to right while coming to a complete stop. The driver took the vehicle to an independent mechanic to be inspected and was informed that the rear driver’s side subframe had separated from the vehicle due to extreme rust. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 115,000.

The rear drivers side had a loud chunking/clanking noise while driving and the vehicle was unable to control and break when in motion. Driving was impossible as the breaking component was a total failure and car could not be controlled while traveling down 45-50mph zone. I reduced my speed to 20-25 mph by letting off on the gas to get better control of the car if breaking would need to be suddenly made. I relied on the shoulder to pull off if any sudden breaking was needed. The car was immediately take to be reviewed by a specialized Mercedes benz mechanic and further inspection proved that the rear subframe on the driver’s (left) side was corroded and broken. The connecting arms are rusted, corroded and rendered the car inoperative. I notified my insurance company as well as car manufacturers corporate office. I researched this issue further and discovered that this reoccurring issue with this make and model. There are a pheletera of recounting of this same issue on various message boards to validate the same issues and callouts I found. The car was taken to the dealership that it was purchased and further inspection showed that the left side subframe/ subframe arms were corroded with rust and broken. The brake lines and fuel tank were equally rusted and corroded. The service manager confirmed that this is defect of the car but it had been part of a recall. I had the car towed for 2nd opinion to another dealership service department to access the car and this callout further

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving approximately 15-20 MPH, there was a rattling noise heard and the vehicle was pulling to the right. The vehicle was taken to the dealer and diagnosed that the rear subframe was rusted and had fractured. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure and opened a case. The contact was awaiting a call back from the case manager. The failure mileage was approximately 120,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated that while driving at various speeds, the vehicle would drift from the center in either direction without warning. After describing the symptoms to an independent mechanic, he was informed that the rear subframe might be corroded. Upon inspection, the contact discovered that the subframe had started to corrode which had caused the failure. The dealer was notified of the failure and informed him that they are aware of the failure however, there was no recall regarding the issue. The contact attempted to notify the manufacturer of the failure but was unsuccessful. The vehicle was not repaired. The failure mileage was approximately 80,000.

The contact owns a 2012 Mercedes-Benz C300. The contact stated that the driver’s side air bag warning light was illuminated. The contact took the vehicle to a certified mechanic who cleared the code. The failure recurred. The vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 93,541.

TL* THE CONTACT OWNS A 2012 MERCEDES BENZ C300. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 45 MPH, A BURNING TYPE ODOR WAS PRESENT INSIDE THE VEHICLE. WHILING INSPECTING THE VEHICLE IT WAS DISCOVERED THAT REAR DRIVER AND PASSENGER SIDE TAIL LIGHT PLUGS HAD MELTED. ALSO, AFTER TURNING THE FRONT DRIVER SEAT HEATER ON A BURNING ODOR WAS PRESENT AND THE SEAT FELT EXTREMELY HOTTER THE NORMAL. THE CAUSE OF THE FAILURES WERE NOT DETERMINED. THE MANUFACTURER AND LOCAL DEALER WERE NOT YET NOTIFIED OF THE FAILURES. THE FAILURE MILEAGE WAS 70,000. ## VIN PASSED ## MERCEDES-BENZ 2012 C300 ##

REAR SUBFRAME (AS RECALLED IN PREVIOUS YEARS) WAS COMPLETED CORRODED - FAILED VIRGINIA INSPECTION - IN SUCH POOR SHAPE THAT ENTIRE SUBFRAME HAD TO BE REPLACED - CORROSION RIDDLED THE PIECE SO THAT HUGE HOLES RESULTED IN NO POSSIBILITY OF WELDING TO FIX/SUPPLEMENT WEAKNESS - AUTO REPAIR PLACE HAD NOT SEEN SUCH A WEAK FRAME IN SUCH A RELATIVELY NEW CAR. LUCKILY - NO ACCIDENT OCCURED BUT COULD EASILY HAVE OCCURRED DUE TO CORROSION. NO OTHER PART OF VEHICLE WAS CORRODED - SO PART WAS MANUFACTURED INCORRECTLY (NO CORROSION CONTROL?/SHIPMENT FROM GERMANY ISSUE?) - MERCEDES BENZ HAS RECALL FOR THIS PART IN PREVIOUS MODEL YEARS - PICTURES OF SUBFRAME AVAILABLE UPON DEMAND

DRIVING LOW SPEED IN TOWN IN FAIR WEATHER AND HIT BRAKES, NOISE AND STRANGE "LOOSENESS" IN BACK END. HAD NEARBY SERVICE STATION INSPECT AND REAR SUB FRAME HAD RUSTED OUT, SEARCHED AND FOUND MULTIPLE REPORTS OF EXACT ISSUE. CONFIRMED W/ LOCAL MB DEALER KNOWN ISSUE AND THEY ARE SEEING ABOUT 1 MONTH NOW.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS NOT YET AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER HAD EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. AN UNKNOWN DEALER WAS CONTACTED AND CONFIRMED THAT PARTS WERE NOT YET AVAILABLE. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. ## VIN PASSED ## MERCEDES-BENZ C300 2012 ##

THE REAR SUBFRAME HAS CORRODED AROUND THE AREAS WHERE THE TRAILING ARM AND CONTROL ARM MEET THE SUBFRAME ON BOTH SIDES OF THE VEHICLE, AND HAS DISINTEGRATED AROUND THE DRIVERS SIDE REAR TRAILING ARM CAUSING IT TO HAVE DETACHED, ALONG WITH A PIECE OF THE SUBFRAME. THE METAL OF THE SUBFRAME IS DISTORTED AROUND THE AREA OF THE BREAK. THE DETACHED TRAILING ARM AND PIECE OF SUBFRAME ARE NOW MAKING CONTACT WITH THE FUEL TANK AS WELL. THE FUEL TANK COULD HAVE EASILY RUPTURED AND IGNITED WHEN THIS CAR WAS STILL IN OPERATION, AS THIS CAR WAS DRIVEN FOR SEVERAL DAYS BEFORE THE MANUFACTURING DEFECT WAS DISCOVERED. THE FAILURE HAPPENED WHEN COMING TO A GENTLE STOP FROM 20-30 MILES PER HOUR ON A STRAIGHT ROAD. THERE WAS A LOUD SNAPPING NOISE FROM THE DRIVERS SIDE REAR. THIS CAR HAD 92,000 MILES AT TIME OF THE STRUCTURAL FAILURE AND HAS BEEN REGULARLY SERVICED, EXCLUSIVELY AT MERCEDES-BENZ. MERCEDES-BENZ USA CUSTOMER SERVICE IS UNABLE TO OFFER ANY ASSISTANCE. THIS EXACT ISSUE HAS LED TO A RECALL OF THE SAME MODEL IN CANADA, AND THERE ARE COUNTLESS NHTSA REPORTS DESCRIBING SIMILAR STRUCTURAL FAILURES. MERCEDES-BENZ USA IS AWARE OF THIS ISSUE AND IS ALSO AWARE THAT THERE IS A RECALL IN CANADA, BUT HAS MADE IT CLEAR THAT GOODWILL WILL NOT BE EXTENDED.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PART TO DO THE RECALL REPAIR WAS UNAVAILABLE. THE CONTACT REACHED OUT TO MERCEDES-BENZ OF MASSAPEQUA (101 SUNRISE HWY, AMITYVILLE, NY 11701, (631) 213-2023) WHERE IT WAS CONFIRMED THAT THE PART WAS NOT YET AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V017000 (AIR BAGS) HOWEVER, THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS). MERCEDES BENZ OF CHANTILLY LOCATED AT 14841 STONECROFT CENTER CT, CHANTILLY, VA 20151, WAS CONTACTED AND THE CONTACT WAS INFORMED THAT PARTS WERE NOT YET AVAILABLE FOR THE RECALL REPAIR. THE CONTACT STATED THAT THE MANUFACTURER HAD EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

I HAVE AN AIRBAG RECALL THAT THE DEALER KEEPS PUTTING OFF. I UNDERSTAND THIS IS A DANGEROUS RECALL AND I NEED TO GET IT FIXED! *TR

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER THE PART TO DO THE RECALL REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE VEHICLE WAS TAKEN TO MERCEDES BENZ OF BILLINGS (3045 KING AVE W, BILLINGS, MT 59102), AND WAS REJECTED TO BE SERVICED DUE TO THE PART NOT BEING AVAILABLE. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND INFORMED THE CONTACT THAT PART WOULD BE AVAILABLE AUGUST OF 2020. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CONTACTED MERCEDES-BENZ OF JACKSONVILLE LOCATED AT (10231 ATLANTIC BOULEVARD, JACKSONVILLE, FL 32225 (855) 979-0550) WHERE IT WAS CONFIRMED THAT THE REMEDY PART WAS NOT AVAILABLE. THE MANUFACTURER WAS NOT CONTACTED AND MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS). THE CONTACT STATED THAT BENZEL-BUSCH MOTOR CAR, AUTHORIZED MERCEDES-BENZ LOCATED AT (28 GRAND AVE, ENGLEWOOD, NJ 07631) EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

TL* THE CONTACT OWNS A 2012 MERCEDES BENZ C300. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PARTS TO DO THE RECALL REPAIR WAS UNAVAILABLE. CAROUSEL MOTORS LOCATED AT (809 IA-1, IOWA CITY, IA 52244) WAS CONTACTED AND CONFIRMED THAT THE PART WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

I RECEIVED A RECALL NOTICE FOR DEFECTIVE AIR BAGS IN MARCH 2019. I CONTACTED THE DEALER AND MANUFACTURER IMMEDIATELY. BOTH STATED THAT THEY DO NOT HAVE A REMEDY. TO DATE, NEITHER THE MANUFACTURER OR DEALER HAS MADE ANY EFFORT TO REPAIR THE DEFECT.

REC'D NOTIFICATION LTR OF FEB 2019 REGARDING RECALL ON AIR BAGS. NO FOLLOW UP ON REPAIR STATUS FOR 1 YEAR. DEALER HAS NO PARTS. THIS IS A SAFETY ISSUE I NEED STATUS AND WHAT ACTION BY MERCEDES IS FORTHCOMING. THANKS, [XXX] REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6) *CC