2014 Kenworth T680

Defect. PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk. If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Remedy. PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

Defect. PACCAR Incorporated (PACCAR) is recalling certain 2013-2019 Kenworth T680 and T880 and Peterbilt 579 trucks, greater than 30 feet long and equipped with side extender mounted intermediate marker lamp/turn signals that do not include a reflex reflector. Since both intermediate side marker lamps and reflex reflectors are required, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. Missing reflex reflectors can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.

Remedy. PACCAR will notify owners and dealers will install reflex reflective tape, free of charge. The recall began January 15, 2019. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 18KWF, and 18PBC.

Defect. PACCAR Incorporated (PACCAR) is recalling certain 2013-2017 Peterbilt 567 and 579 Kenworth T680 and T880 trucks equipped with optional spotlights. The spotlight circuit may not be adequately protected in the event of a short.

Risk. A short in the spotlight circuitry may increase the risk of a fire at the cab fuse block.

Remedy. PACCAR will notify owners, and dealers will change the polyfuse switch in the spotlight circuit to a standard fuse, free of charge. The recall began on September 19, 2017. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 17KWC and 717-B.

Defect. PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T440, T470, T660, T680, and T880 trucks manufactured January 14, 2010, to May 22, 2015, and equipped with HID Headlamps and the option for Daytime Running Lamps (DRL). The DRLs are required to deactivate when the hazard warning lights are activated, however, the DRLs on these vehicles override the hazard flashing functionality after the brake pedal is pushed for more than two seconds. Normal hazard flashing functionality returns once the service brake is released. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk. If the hazard warning lamps are overridden by the DRL, oncoming vehicles may fail to be warned, increasing the risk of a crash.

Remedy. Kenworth will notify owners, and dealers will update the cab controller software, free of charge. The recall began on September 167, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWL.

Defect. PACCAR Incorporated (PACCAR) is recalling certain model year 2014 and 2015 Kenworth T660, T680, and T800 trucks manufactured January 29, 2013, to April 2, 2014, and 2013 Peterbilt 587 trucks manufactured on August 8, 2012. The affected trucks are built with a driveshaft that may not transmit power to the wheels due to weld failure from corrosion.

Risk. If the weld fails causing a loss of power to the rear wheels, the vehicle operator may be unable to move the vehicle, or may experience deceleration if the vehicle is in motion, increasing the risk of a vehicle crash.

Remedy. PACCAR will notify owners, and dealers will replace the defective driveshafts, free of charge. The recall began on July 15, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, or Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 15KWJ and 515-H.

Defect. PACCAR Incorporated (PACCAR) is recalling certain model year 2014-2016 Kenworth T660, T680, T880 trucks manufactured February 18, 2013, to April 10, 2015, and 2011-2016 Peterbilt 386, 389, 567, 579, and 587 trucks manufactured December 13, 2010, to April 20, 2015. The affected trucks, equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

Risk. If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

Remedy. PACCAR will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line, free of charge. PACCAR issued an interim notification to owners on July 10, 2015. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 15KWE and 515-F.

Defect. PACCAR Incorporated (PACCAR)is recalling certain model year 2013-2014 T660, and T680 vehicles manufactured from December 4, 2012, through September 17, 2013 and configured as a dead axle tandem with air disc brakes and spring brake delete options. The affected vehicles have the parking brake incorrectly placed on the non-driven rear axle.

Risk. If the parking brake is on the non-driven axle the vehicle could roll away when the parking brakes are set, resulting in an increased risk of a crash.

Remedy. PACCAR will notify owners, and dealers will move the parking brake components to the forward wheel axle, free of charge. The recall began on April 9, 2014. Owners may contact PACCAR at 1-425-468-7400. Paccar's number for this recall is 14KWE.

Defect. PACCAR Inc. is recalling certain model year 2013-2014 Kenworth T680 chassis manufactured January 1, 2012, through October 14, 2013, and Peterbilt 567 and 579 chassis manufactured January 20, 2012, through October 11, 2013, and equipped with Inteva-brand door latch assemblies. In the affected vehicles, the doors may lock permanently while closed or may be opened from the outside even after they have been locked.

Risk. If the door latch assembly becomes permanently locked while closed occupants could be prevented from exiting the vehicle in the event of a crash or fire, increasing the risk of injury.

Remedy. PACCAR will notify owners, and dealers will replace the left and right door latch assemblies with new assemblies, free of charge. The recall began on March 25, 2014. Customers may contact Paccar at 1-425-468-8228. Kenworth's number for this recall is 14KWB. Peterbilt's number for this recall is 114-A.

Defect. PACCAR Incorporated (PACCAR) is recalling certain model year 2014 Kenworth T660, T680, T700,T800, T880, W900, T440, T470, T370, T270, T170, C500, and C550 chassis manufactured between August 7, 2013, and October 31, 2013, and Peterbilt 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 chassis manufactured between August 7, 2013, and November 3, 2013, and equipped with IMMI-brand L9 seat belt buckles. When the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 209, "Seat Belt Assemblies."

Risk. If the latch plate remains partially engaged after the button is pressed, egress from the vehicle could be hindered which would increase the risk of injury in the event of an emergency.

Remedy. PACCAR will notify owners, and dealers will inspect and replace the seat belt buckles, as necessary, free of charge. The recall began on March 31, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's number for this campaign is 14KWC. Peterbilt's number for this campaign is 114-B.

Defect. PACCAR Incorporated (Paccar) is recalling certain model year 2014 Kenworth T170, T270, T370, T440, T470, T660, T680, T700, T800, T880, C500 and W900 trucks manufactured July 1, 2013 through September 17, 2013. In the affected vehicles, the plastic housing of the Stop/Tail/Turn (STT) lamp can shrink and allow the light bulb to fall out of the mounted retention ring. As such, the Stop/Tail/Turn light would not be illuminated, and the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) No. 108 "Lamps, Reflective Devices, and Associated Equipment."

Risk. If the stop/tail/turn light is not illuminated, the driver's intentions would not be communicated, which increases the risk of a crash.

Remedy. Kenworth will notify owners, and dealers will replace the defective STT lamps with new lamps. The recall began on February 4, 2014. Customers may contact Paccar at 1-425-468-7400. Kenworth's number for this recall is 13KWM.

This Truck Was Park. The Paccar Engine MX13 and Chassis Harness from the Driver Side Shortaged, causing a Fire in the back of the engine and ABS Harness under the Steering Shaft. Plástic and Rubber wire insulation Melted with the fire causing it to drip on top of the water seperator cap which resulted in a fuel flame that caused even more damage throughought the outstanding components. This problem could've resulted in total loss of the unit.

APPARENTLY THERE IS A FAILURE OF THE FUEL PUMP IN MOST MODELS OF THIS CUMMINS ISX15 MOTOR, THA WHEN IT DOES FAIL, SHUTS THE TRUCK DOWN ON HIGHWAY, OR WORSE, LIK EIT DID TO ME....SEND METAL SHAVINGS INTO THE REST OF THE MOTOR DESTROYING THE MOTOR. THERE HAVE BEEN RECALLS FOR CERAMIC PLUNGERS, WHICH I DON'T HAVE...AND RECALLS ON MANY YEARS THIS MODEL WAS MANUFACTURED. I HAVE AN EXTENDED MAJOR COMPONENT WARRANTY THAT CUMMINS WILL NOT HONOR SINCE THE FUEL PUMP FAILURE IS NOT COVERED.....DEALER HAS WITNESSED MANY FAILURES OF THE FUEL PUMPS AND NOT ALWAYS COVERED...EVEN THOUGH REPAIR OR REPLACEMENT OF ENGINE IS IN EXCESS OF $20000 TO $35000 FOR A NEW REPLACEMENT. THIS NEEDS TO BE ADDRESSED WITH CUMMINS !!

A VIBRATION IS FELT DURING WARM UP AND BECOMES VERY NOTICEABLE AFTER SHIFTING INTO 8TH GEAR. IF THE AIR COMPRESSOR KICKS IN WHILE THE ENGINE IS BELOW 1300 RPMS THIS ALSO INCREASES THE VIBRATION , AGAIN REAL BAD SHIFTING INTO 8TH AND AIR COMPRESSOR RUNNING .NOTE: I JUST BOUGHT THIS TRUCK FROM KENWORTH SALES COMPANY , SALT LAKE CITY, UT I AINT EVEN PUT 2,000 MILES ON THE TRUCK, WHAT KINDA OF DECEITFUL ETHICS VIOLATIONS ARE PRACTICED FROM THIS DEALERSHIP?

BUNK WIRING HARNESS IS SHORTING OUT CAUSING TRUCK TO NOT BE ABLE TO SHUT OFF WITH THE KEY....AND ALSO CAUSING PROBLEMS WITH THE DEF SYSTEM....SHOPS ARE TELLING US THAT THERE ARE TRUCKS BURNING DOWN FROM THIS FAULTY HARNESS...AND THERE HAS BEEN A RECALL FOR THIS BUT KENWORTH IS NOT FIXING THIS HARNESS AND EXPECTS THE OWNER TO FIX IT ....

THIS TRUCK IS A MISBUILD FROM THE FACTORY ON THE BRAKE SYSTEM PLUMBING. I AM CONCERNED OTHER UNITS MAY ALSO HAVE BEEN BUILT WRONG. THE TRACTION CONTROL LOCKS UP THE FRONT DRIVE AXLE BRAKES WHEN THE TRUCK SPINS A TIRE AND KILLS THE ENGINE CAUSING DAMAGE TO THE DIFFERENTIAL AND LOSS OF CONTROL OF THE VEHICLE. I HAVE IDENTIFIED THAT THE SERVICE BRAKE AIR LINES ARE HOOKED UP INCORRECTLY FROM THE FACTORY, NOT GOING THROUGH THE ABS MODULATOR VALVE. THIS ALLOWS FULL BRAKE APPLICATION TO THE FRONT DRIVE AXLE SERVICE BRAKES WHEN THE TRACTION CONTROL ENGAGES. IT ALSO MAKES THE TRUCK SO THE ABS BRAKE FUNCTION IS NOT ABLE TO FUNCTION. WE HAVE BLOWN APART 2 FRONT DIFFERENTIAL UNITS RENDERING THE TRUCK UNABLE TO MOVE. OFTEN WHEN THIS HAPPENS IT KILLS THE ENGINE SO NOW YOU ALSO LOOSE POWER STEERING CONTROL. THIS IS AN EXTREMELY UNSAFE AND ILLEGAL BUILD ON THIS TRUCK. ABS IS REQUIRED BY DOT LAW AND THIS TRUCK DOES NOT HAVE FULL ABS FUNCTION. I HAVE CONTACTED BENDIX, THE MAKER OF THE ABS AND TRACTION CONTROL THEY HAVE CONFIRMED THE WAY THIS IS HOOKED UP WILL CAUSE THE BRAKES TO LOCK UP. I HAVE ATTACHED PICTURES OF THE VALVE, YOU WILL NOTICE THAT ONE AIR LINE COMES FROM THE MODULE WHICH GOES TO THE REAR BRAKE. THE OTHER AIR LINE COMES DIRECTLY OUT OF THE ATR6 BRAKE VALVE, THIS LINE GOES DIRECTLY TO THE FRONT DRIVER SERVICE BRAKE. IT SHOULD ALSO BE RUN THROUGH THE MODULATOR VALVE FOR PROPER FUNCTION. THIS HAS HAPPENED AT ALL SPEEDS IN ICY SITUATIONS. IT HAS HAPPENED ON MOUNTAIN PASSES AND LEAVE

THE DEFROST DOOR HAS BROKEN IN THIS VEHICLE FOR A SECOND TIME. THE KENWORTH DESIGN IS PROBLEMATIC AND EVEN THE NEW PARTS ONLY FIX THIS FOR A SHORT TIME. DRIVER NO LONGER HAS DEFROST WHEN THIS HAPPENS MAKING IT AN UNSAFE DRIVING SITUATION. VEHICLE WAS IN MOTION AT THE TIME IT BROKE.

THIS IS THE FIRST OF 2 TIMES THE DEFROST DOORS HAVE BROKEN IN THIS TRUCK. THE DEFROST DOORS IN THE T680 ARE WEAK AND BREAK OFTEN LEAVING THE DRIVER WITHOUT ANY DEFROST CAUSING HIS VISIBILITY TO DECREASE IN AN UNSAFE MANNER. KENWORTH HAS BEEN UNWILLING TO ADDRESS THIS ISSUE AND REPAIR IT. WHEN I CONTACTED OUR DISTRICT SERVICE MANAGER HE KNEW THE PART NUMBER OF THE REPLACEMENT DOOR ASSEMBLY FROM MEMORY AND STATED IN AN EMAIL BACK TO ME THAT KENWORTH HAS IDENTIFIED THE ISSUE AND IS WORKING TO FIX IT ON FUTURE MODELS. LABOR TO REPAIR THIS IS OVER $3000 AND THE PART IS ANOTHER $886. WE HAVE 12 OF THESE VEHICLES, SO FAR 5 OF THE 12 HAVE BROKEN LEAVING MORE THAN ONE DRIVER STRUGGLING TO GET OFF THE HIGHWAY BEFORE HIS WINDOW FOGGED UP SO BAD HE BECAME UNSAFE TO DRIVE. THE VEHICLES ARE IN MOTION WHEN THESE DEFROST DOORS BREAK AND IT CREATES A VERY UNSAFE SITUATION AS TRUCKS CAN NOT JUST PULL OVER ANY SPOT THEY CHOOSE ON THE HIGHWAYS AND WAIT FOR A WINDOW TO THAW OUT. THERE ARE 2 ISSUES THAT HAPPEN ON THESE DOORS. 1 THE DOOR IS OVERFLEXED BY THE ELECTRIC ACTUATOR MOTOR AND SNAPS THE DRIVE COGS OFF OF THE DOOR. 2 THE DOORS EITHER SHRINK OR ARE TOO SMALL TO BEGIN WITH AND THE DRIVE COG DOES NOT MAKE FULL CONTACT WITH THE ACTUATOR MOTOR CAUSING THE TEETH TO STRIP OUT AS IN THE PHOTOS ATTACHED. THE DRIVE COG SHOULD BE EXTRUDED FROM THE HOUSING BUT AS YOU CAN SEE ARE SHRUNK INSIDE THE HOUSING. *TR

THIS IS THE SECOND TIME THE DEFROST DOORS HAVE BROKEN IN THIS VEHICLE LEAVING THE DRIVER IN AN UNSAFE DRIVING CONDITION. THE FIRST TIME WAS 4/25/16 THE DEFROST DOORS IN THE T680 IS WEAK AND BREAKS OFTEN LEAVING THE DRIVER WITHOUT ANY DEFROST CAUSING HIS VISIBILITY TO DECREASE IN AN UNSAFE MANNER. KENWORTH HAS BEEN UNWILLING TO ADDRESS THIS ISSUE AND REPAIR IT. WHEN I CONTACTED OUR DISTRICT SERVICE MANAGER HE KNEW THE PART NUMBER OF THE REPLACEMENT DOOR ASSEMBLY AND STATED IN AN EMAIL BACK TO ME THAT KENWORTH HAS IDENTIFIED THE ISSUE AND IS WORKING TO FIX IT ON FUTURE MODELS. LABOR TO REPAIR THIS IS OVER $3000 AND THE PART IS ANOTHER $886. WE HAVE 12 OF THESE VEHICLES, SO FAR 5 OF THE 12 HAVE BROKEN LEAVING MORE THAN ONE DRIVER STRUGGLING TO GET OFF THE HIGHWAY BEFORE HIS WINDOW FOGGED UP SO BAD HE BECAME UNSAFE TO DRIVE. THE VEHICLES ARE IN MOTION WHEN THESE DEFROST DOORS BREAK AND IT CREATES A VERY UNSAFE SITUATION AS TRUCKS CAN NOT JUST PULL OVER ANY SPOT THEY CHOOSE ON THE HIGHWAYS AND WAIT FOR A WINDOW TO THAW OUT. *TR

THE DEFROST DOOR BROKE ON THIS TRUCK LEAVING THE DRIVER STRANDED WITH NO DEFROST AND ABILITY TO SAFELY DRIVE THE VEHICLE UNTIL THE WINDOWS CLEARED OFF. THE DEFROST DOORS IN THE T680 IS WEAK AND BREAKS OFTEN LEAVING THE DRIVER WITHOUT ANY DEFROST CAUSING HIS VISIBILITY TO DECREASE IN AN UNSAFE MANNER. KENWORTH HAS BEEN UNWILLING TO ADDRESS THIS ISSUE AND REPAIR IT. WHEN I CONTACTED OUR DISTRICT SERVICE MANAGER HE KNEW THE PART NUMBER OF THE REPLACEMENT DOOR ASSEMBLY AND STATED IN AN EMAIL BACK TO ME THAT KENWORTH HAS IDENTIFIED THE ISSUE AND IS WORKING TO FIX IT ON FUTURE MODELS. LABOR TO REPAIR THIS IS OVER $3000 AND THE PART IS ANOTHER $886. WE HAVE 12 OF THESE VEHICLES, SO FAR 5 OF THE 12 HAVE BROKEN LEAVING MORE THAN ONE DRIVER STRUGGLING TO GET OFF THE HIGHWAY BEFORE HIS WINDOW FOGGED UP SO BAD HE BECAME UNSAFE TO DRIVE. THE VEHICLES ARE IN MOTION WHEN THESE DEFROST DOORS BREAK AND IT CREATES A VERY UNSAFE SITUATION AS TRUCKS CAN NOT JUST PULL OVER ANY SPOT THEY CHOOSE ON THE HIGHWAYS AND WAIT FOR A WINDOW TO THAW OUT. THERE ARE 2 ISSUES THAT HAPPEN ON THESE DOORS. 1 THE DOOR IS OVERFLEXED BY THE ELECTRIC ACTUATOR MOTOR AND SNAPS THE DRIVE COGS OFF OF THE DOOR. 2 THE DOORS EITHER SHRINK OR ARE TOO SMALL TO BEGIN WITH AND THE DRIVE COG DOES NOT MAKE FULL CONTACT WITH THE ACTUATOR MOTOR CAUSING THE TEETH TO STRIP OUT AS IN THE PHOTOS ATTACHED. THE DRIVE COG SHOULD BE EXTRUDED FROM THE HOUSING BUT AS YOU CAN SEE ARE SHRUNK INSIDE THE HOUSING. *TR

THE TIE ROD END DISCONNECTED FROM THE SHAFT, THERE HAS BEEN NO WORK DONE TO THE STEERING SINCE NEW. THE PICTURES SHOW THAT THE DIRT ON THE SHAFT HAS NOT BEEN DISTURBED THEREFORE THIS IS A MANUFACTURER DEFECT AND HAS NOT BEEN TAMPERED WITH AT ALL. THE VEHICLE WAS MOVING AT SLOW SPEED IN A PARKING LOT. THIS COULD HAVE BEEN A MAJOR EVENT AT HIGHWAY SPEED. I HAVE CONTACTED THE MANUFACTURER. THIS TRUCK HAS HAD REGULAR SERVICE MOST RECENT BEING MARCH 12TH, NO SIGN OF THE DEFECT WAS NOTICED AT THAT TIME AND THIS PART WAS INSPECTED. AS YOU SEE FROM THE PICTURE, THE PART MUST HAVE BEEN WEARING FOR A LARGER TIME PERIOD THAN AN IMMEDIATE EVENT. THIS PART IS USED BY MANY MANUFACTURERS FOR THEIR PRODUCTS ALSO.