2016 Jeep Wrangler complaints

ABS module faulty with none available to have fixed under warranty. I was told to drive it anyway.

My ABS Control module has failed. The Jeep has been in the shop now for 75 days with no MOPAR part delivery known as of 11/28/25. I have had 4 ABS wheel sensors go bad and not the module is bad. The vehicle surges, will not accelerate, etc.

ABS module started to fail about a year ago but was only recently identified (within the last two weeks). ABS module listed for back order with more than 500 orders ahead of mine within Jeep dealership system. Order placed outside of dealership via Mopar website but listed as shipping next month (16-28 December).

The contact owns a 2016 Jeep Wrangler. The contact recently replaced the windshield wiper motor due to a failure of the intermittent speed settings not functioning properly. The contact stated that after replacing the wiper motor, the contact was only able to use the wipers on the fast speed setting. An independent mechanic informed the contact that the vehicle was taken to the shop for repair, or he could replace the wiper blade switch on the steering column. The contact repaired the vehicle himself. The contact stated that after the repair was completed, while driving out of the driveway at approximately 2 MPH, the driver's side front air bag deployed. The contact followed the instructions to install the wiper blade switch carefully. The contact was still only able to use the wipers on the fast speed setting. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was 132,552.

Oil holder thing had to be replaced twice within a few months for the part leaving oil onto the engine.

The ABS Module has failed causing the stabiltrak , brake light , and ABS lights to come on the dash. We took it to the dealer and evidently this is a common issue with the jeep wranglers and dodge rams.. So much that the part is back ordered and there is no eta. Some people have been waiting over a year. They say it’s under engineering review. Anyway My Wife was driving the other day and someone had pulled out in front of her and she hit the brakes real hard and it made a weird noise and the brakes locked up. Almost causing her to swerve and lose control. I have the service report that says ABS module and backed ordered with no eta.. I have heard other peoples jeeps just going over to broke mode and can only drive 30 mph. It’s crazy? What are we the consumer supposed to do. Can’t afford to trade it in for another vehicle. But need a vehicle for work or keep driving it and hope brakes or something else doesn’t fail when you need it… Thank You

My ABS module has been out/faulty for more than two years. I have been unable to get a repair/replacement part due to national back orders. Chrysler has been no help at all. I believe this is a safety issue that Chrysler isnt taking serious.

The abs module has gone bad at less then 70,000 miles the dealership confirmed this. There are lights advising of the abs and traction control light on and I no longer have anti lock breaks or traction control.

Our Abs control module is firing out an internal error code. Mopar has the unit on back order. It has been on back order for more than a year. To get a used one costs 5 times more than a new one. This is a huge problem for people when it comes to safe driving.

My 2016 Jeep Wrangler is displaying warning lights (Brake, ABS, Traction Control) on the dashboard. I took it to my Jeep dealership where they diagnosed the issue as an inoperative ABS Module part number 68259556AD. They placed it on order but it was back ordered with no available delivery date. My Jeep is now not able to be driven.

Jeep Wrangler Unlimited ABS, Brake, & Traction Control warning lights all came on at once while driving. Once jeep stopped vehicle went into limp mode limiting power and MPH to less than 30 MPH. Which is a huge safety problem when all the roads to and from out house are 45 MPH. ABS Module is bad per the dealer. Vehicle is VOR in the system, and undriveable. No estimate when a new part will arrive.

On September 2, 2025, while driving at 65 mph, I lost control of my vehicle three times. The traction control light came on each time, creating a serious safety risk to me and others. The issue appears to involve the airbag clockspring/steering column assembly, matching symptoms reported under Safety Recall 27B (RC-27B-24). My VIN is not currently included in the recall. Chrysler Dodge Jeep Ram opened Case #94164354 and advised me to submit this so my VIN can be added. The part is available for inspection. My car is not drivable at this time due to the safety issue.

The jeep has an ABS module that went bad. I have been waiting months- perhaps over a year, and there is still no estimate on the part coming in. It is an essential part, one with no generic replacement. It is illegal for jeep to just leave all of us hanging.

In February of 2024, my ABS, traction control and brake warning lights came on. This disables the ABS, traction control and cruise control. After scanning the vehicle for codes, there is a C2200 internal fault for the ABS control module. Making sure it is not a sensor issue, I tested all four wheels and all check out fine. Looking up the C2200, I would need to replace the module. The problem is, the module has been on national backorder since December 2023 with no end in sight. My only option is to either send that module out to a company and pay $450 plus shipping to have it rebuilt or to pay upwards of $1400 for it on eBay. Even then, it may not be a genuine or new part. I have a vehicle with a safety feature that failed and another 2016 Jeep Wrangler that is starting to show similar symptoms. Stellantis / Mopar is of zero help and will not tell me when or if the part will be available.

The anti lock brake module is not signaling correctly, causing the car to lose power for a second every few minutes, braking is more difficult, and there is no traction on slippery surfaces. The cruise control also is not working, and the brake, ABS and traction warning lights flash every few minutes while operating. It was in the shop for a month waiting on the new module, and it is back ordered with no estimated date for shipping. My vehicle is under warranty and I’m not able to go outside the terms to get it fixed, and Mopar is not making any effort to provide a solution. The dealership even said they had another that had been sitting in their shop for over a year with the same problem. The car is drivable but only until the system goes completely, which will be when it goes into emergency limp mode at a random time while driving, so driving it means taking on that risk.

Anti Lock Brake Control Module (C2200). Cannot get part anywhere, on vehicle appears codes preventing cruise control and other safety issues

ABS control module cannot get the part so i would think this would be a safety issue because abs is not working. I know alot of other people who have a jeep have the same proplem my part has been on back order for 4 months now. So I'm concerned about not having ABS thank you

ABS control module malfunction. Replacement part not available from dealership or 3rd party supplier, with item on continuous backorder. ABS and Traction control lights permanently on whilst engine running. Potential safety concern across model nationwide?

The ABS module has quit working and Stellantis and our local Jeep Dealership keeps saying the part is back ordered or under Engineering review and this has been going on for 2 years. With the ABS module not working some of the vehicles systems do not work as designed. Obviously the ABS system is deactivated. The module also controls the cruise control, anti hill assist and there is noticeable difference of how the automatic transmission shifts and at what RPM it shifts. Since the module has been declared and not available and appears there is no replacement available from Stellantis and Jeep this leave me with a vehicle that parts have failed that are important and designed for the vehicle safe operation and not recourse available to me or other others of Jeep Wranglers with similar or worse problems. Stellantis and Jeep need to come up with an alternate ABS Module or a fix to the modules on my vehicle.

The ABS Control Module has failed (part number 68259556AD). I have discovered it has been unavailable from Chrysler/Jeep for over 2 years. I read where this is a dispute between Chrysler/Jeep and their supplier of the part. I feel it dangerous not to have my ABS system, and it seems the manufacturer is doing nothing to make the part available. This needs to change.

The front passenger seatbelt wasn’t working properly and we noticed the belt was frayed so we ordered a new one from car parts direct. Today while taking the old belt out we noticed that the seatbelt unit itself wasn’t bolted into the jeep. It was bolted off to the side causing it to be crooked which is why the belt frayed because the entire unit was not in properly. The bolt that should be holding it in is still in the jeep yet the seatbelt unit came out very easily and you can clearly see where the bolt was sitting. I will include photos.

The ABS Pump Module on Jeep Wranglers are not working and Stellantis/Wrangler has stopped making replacement parts. If you look on [XXX] you can see that this is a nationwide issue and impacts Wrangler models spanning over several years (so far I've seen from 2014-2019). I've been trying to get the part for over a year to no avail. Also, the part is tied to the vehicle's VIN number, so you cannot use one from another Jeep (for example one from a junk yard). The safety issue is that the automatic braking system does not work properly. My Jeep also fishtails when driving in the rain. There are warning lights on the dash, which come on and off randomly. Mine do not stay on permanently. Initially, I tried to get this part replaced at a Firestone in CA, and then tried again at a mechanic in TX. Both told me the same thing, that the part is unavailable, no longer being made and that it is a national issue. A recall has not been issued either. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

This vehicle is not suitable for driving, it has suspension, alignment, brake and speed problems. I was about to have an accident, I was going down an avenue and suddenly the wheels stopped and the car began to move from one side to the other and I lost stability of the steering wheel and the car, putting my life and the lives of my family (my girlfriend and my mother) at risk, luckily I did not cause an accident because there was no car in the side lane ... It is impossible to drive this car, the next day I took the car to a detailed inspection at a mechanical workshop specialized in Jeeps and indeed it has serious and serious problems with the car. There are images where the lights on the dashboard are on and the engine is also overheated ... For this reason, I decided to return the car to the dealer and file the report as evidence of this defective car and dangers to driving ...

ABS control module failure. The part is discontinued and no longer available. This makes my vehicle unsafe to drive for myself and others on the road. Thus, being unsafe to drive makes he vehicle useless!

After I made a left turn onto a four-lane highway, the transmission stuck in first gear and I wasn't able to get over to the shoulder because of traffic passing on the right side. I was nearly rear-ended twice before finally being able to exit with a left turn. The engine light came on soon after this happened.

Brake failure referenced in case # 11667897. See attached photos for reference to affected areas.

Left front brake caliper not releasing. Replaced caliper and brake pads, problem still exist. After some research found that there has been an issue with brake line. Apparently the mounting bracket on the line has in some cases pinched the line restricting fluid flow causing brake to not release fully. Have seen multiple instances of this problem on line. Curious why Jeep has not addressed this issue? Am currently waiting for new brake line to replace existing one to attempt to correct the problem. For reference I am a certified mechanic and this is my personal vehicle which is why I am preforming the repair myself.

Side impact and full 6 rollovers, with damage to front. During an accident on 6/13/25. I took pictures if you need them

The contact owns a 2016 Jeep Wrangler. The contact stated that upon attempting to alert a gateman using the horn, the horn failed to function. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the clock spring. The contact was informed that the clock spring needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 16V288000 (Air Bags), but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 106,000.

ABS module is failing (confirmed by repair shop) and needs replacement, and ABS light had illuminated. After finding out the Dodge/Jeep has discontinued manufacture of this part that is in every 2012-2020 Wrangler, this poses a very serious safety concern as no replacement part is available. Possibility of purchasing a used one that ultimately will have the same result as the original one that was in the vehicle. A recall needs to be made before this becomes a major issue.

For the last 1.5 years the ABS control module light, check engine light, and the traction control light is on. I have taken my jeep to multiple dealers and mechanic shops for this issue and I am repeatedly informed the ABS control module is not in production. It is the only vehicle I own and I fear for my safety. I need to replace this part but the manufacturer is not selling to the dealer or mechanic shops. Can you help me find this part?

December 2024 the abs module failed on my 2016 Jeep Wrangler. Dropped it off at the mechanic and it is now May 2025 with no help from the manufacturer. This is a severe safety issue with the brakes locking up and causing the jeep to not be functionable. I keep seeing recalls for other years makes and models. I need someone to help with a recall on my jeep's abs module and to get a solustion to get my jeep back functioning safely again. I can not drive it at this moment because of this issue.

Oil cooler/filter housing leaking oil and coolant.

Horn stopped working. Steering wheel controls stopped working. Airbag clockspring bad. Several lights on, on dash. Several dealerships claim even though there is a recall, my Jeep is not covered.

Brakes are sticking causing extreme heat and damage to pads, rotors and calipers and I'm afraid there is a fire hazard as well. The brake also occasionally engage during acceleration at around 45 mph and cause a severe wobble that could also be a safety issue as the vehicle becomes hard to control. Dealership claimed the problem was a single brake line that was replaced, but the problem is still occurring and now they claim it is a second brake line but my mechanic assures me it is a faulty ABS module and the online reports indicate this is a real problem with jeep wranglers.

This vehicle along with many others jeep wranglers have an issue with the abs control module. It has a code for internal processor fault. Some days the vehicle is fine and others it acts up and it won’t shift gears or the abs system activates by itself or the speedometer doesn’t work. This has been going on for almost a year now because there is no parts aviable to fix it. The dealer keeps saying it’s in engineering review but they been saying that for almost a year now. That’s how long mine has been acting up. My wife won’t even drive it with the kids in the car because she doesn’t know when it is going to act up. Luckly I only work 5 miles from my house so I’ve been driving it. If they know there’s an issue with these modules they should be doing something faster to fix it or there should be a recall. Something needs to be done.

ABS module needs replacement. Impossible to find one in stock. Dealership claims it’s on back order for a year.

The contact owns a 2016 Jeep Wrangler. The contact stated that the ABS, traction control, and service brake warning lights were illuminated. The ABS and cruise control were inoperable. The traction control was inoperable while driving in the mountains and in snow. The local dealer was contacted, who informed the contact that the parts were on backorder to repair the vehicle. The vehicle was not diagnosed or repaired. The contact called another local dealer, AJ Dohmann Chrysler Dodge Jeep Ram (24945 LA-1 S, Plaquemine, LA 70764), who confirmed that the parts were on backorder. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 60,000.

The ABS control module has malfunctioned which lead to the ABS, traction control, and parking brake light coming on while driving. This is a safety concern due to a malfunction with these systems. These systems are meant to help control the vehicle when either sliding or braking quickly. An OBD scan tool was used, which read the code C2200 to confirm the malfunction.

ABS Module not working and Jeep does not have a solution

ABS control module has been out for almost 2 years. Jeep will not make/replace this part, although promised it would become available for this entire 2 year timeframe.

Oil Cooler leaking after multiple replacements causing engine stall while driving and lots of burning and smoke potentially leading to fire.

In December of 2024, my jeep felt like a ghost was pressing my brakes. It got worse over time despite any troubleshooting we did and replacing sensors did not work. It went inot limp mode and would not drive out of second gear. Took it to my mechanic to find there is a national issue and back order problem with all ABS modules for Mopar/Jeep. I have read many jeep forums online and this issue started in 2020. As of now since January there is no true ETA on the replacement part. My jeep sits while paying for it and unable to repair. We sought a company to try to rebuild the old one and they can't either since the replacement chips are back ordered as well. Luckily I noticed the issue while driving slow on a dirt road, however, this issue could have pulled the vehicle into oncoming traffic or off the side of the road. Jeep has not issued a recall or any help for the ones that are not inoperable. Someone needs to step up and take responsibility for this issue. There are thousands of people involved from what I have read. Please help!

The contact owns a 2016 Jeep Wrangler. The contact stated that while the vehicle was parked in the garage, the contact became aware of an oil leak. The contact stated that the leak was small. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was diagnosed and determined that the engine oil cooler needed to be replaced. Additionally, the contact had previously replaced the thermostat at an independent mechanic due to the parts being on backorder. The contact stated that the failure might be due to the cold temperatures. The vehicle was repaired, but the failure recurred. The manufacturer was not contacted. The failure mileage was approximately 43,000.

The contact owns a 2016 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the ABS warning light illuminated. The vehicle was taken to the dealer, who determined that the ABS module had malfunctioned and needed to be replaced; however, the contact was informed that replacement parts were under engineering review and not yet available. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 92,239.

ABS module defect. Unable to obtain part for almost a year. March 16, 2024 vehicle started shaking violently. All dashboard lights started blinking. Was driving approximately 50 mph at the time. Tried slowing down, no matter the speed, shook so hard could not keep vehicle in lane.

While driving the ABS would activate the left front wheel and pulls to left. Previous all of the wheel sensors had been replaced. Took to dealership first time and could not duplicate problem. Problem happened again and return vehicle to dealership. The ABS, traction and possible another light was on. Took back to dealership and they did flow chart and found the ABS control module was bad. The part was on national back order. Car was non drivable from March 25, 2024, till February 21, 2025, when part came in. This dealership is in a small town, and they had approx. 8-10 vehicles waiting for the same ABS problem (module). This to me is a very hazardous problem because this happen while on highway driving 55 mph with a single mom and her child, thank goodness there was not an accident. NOTE: Do have invoices to send not available at this time. Dealership York Automotive CDJRF, 1765 US 231 Crawfordsville, IN 47933

ABS module inoperative, needs replaced. Brake light,ABS light and downhill assist lights all illuminated as dash warning lights. Jeep has no replacment or repair option available. This is my second report for this problem.

ABS MODULE

ABS Contol Module Failed in December 2023. Jeep did not have the part at the time, I was told it was on engineering hold. Fast forward to March 2025 and the part is still not available from any dealer and they cant tell me when it will be available. I am forced to drive the vehicle with no antilock brake feature and Jeep will not repair, provide part, or provide a loaner vehicle after over a year of waiting. If something happens, I will definitely bring a lawsuit against them. I know that this is a very common problem and there are thousands, if not tens of thousands, of Jeep owners that are in the same boat as me. If we can't rely on ya'll to take some action, what else are we left to do???