2013 Jeep Wrangler complaints

The contact owns a 2013 Jeep Wrangler. The contact stated while driving approximately 30 MPH, while depressing the accelerator pedal the vehicle failed to respond. The contact stated that it felt as if the transmission had seized. The contact stated that the RPM was revving however, the vehicle failed to respond. The contact stated there was no warning light illuminated. The contact stated that during a state inspection, the contact was informed that the passenger’s side rear axle shaft seal was leaking. The contact had taken the vehicle to a local dealer; however, the vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 116,000.

ABS module has gone bad and Jeep Chrysler dealership has told me that they only have nine parts in the nation to replace it and the engineers are not confident in the replaced part, they won’t know when the part would be available and I was also told that if I continue to drive it I could potentially damage other components of the Jeep Wrangler. I was also told by personal mechanic that I shouldn’t drive it as I don’t not have Anti lock breaks..

Clock spring assembly had to be replaced. Horn would not work due to this. This appears to be a problem in jeeps but no recall yet on this specific model

The contact owns a 2013 Jeep Wrangler. The contact stated while driving at approximately 40 MPH the "air bag" warning light illuminated and the horn became inoperable. The contact stated that the failure occurred at various speeds. The contact stated that the failure was intermittent. The contact was aware of an Extended Warranty for the clockspring. The contact had driven the vehicle to a local dealer however, the dealer was unable to retrieve diagnostic trouble codes associated with the clockspring, and the vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 115,000.

While I was attempting to park my jeep across the street from my grandson's school to pick him up at 3:18, as I proceeded to pull in front of the apron so I could backup to a parking spot. In the process of going forward before I got a chance to put the jeep in reverse my brakes failed, hitting a parked car in front of me. I had my jeep towed to Old Center Island Auto Service. The mechanic removed a defective power brake booster and replaced it with a new one.

Unknown

The fuel supply line that attaches to the fuel rail at the engine sprung a leak at the seam were the plastic tube is sealed together. This is a high pressure line. This resulted in fuel being sprayed directly on the hot cylinder head creating a potential fire hazard.

The oil pressure sensor, I was in traffic and the vehicle came to a stop with scared the hell out me and this has hall a couple of time and came to find out it was caused by the oil pressure sensor. Why this is not on recall

Michelin Defender Tire with ~90% tread exploded with no indicators or warning. VDOT repairman indicated that it had exploded from the side. Incident happened on the highway 2/24/24 going 60mph. Jeep did not observe any potholes, road debris, or curbs. I do not do off-roading. Tires had 35psi. I drive average 6000 miles a year. Tire: LT 285/70R17 121/118R dot 1b7 bf 005x 2922 load range E. Wheel: PRC 7069/AT L 13+JK 17X9 33X12.50 R17 employee from tirerack.com confirmed tire/wheel are a match. Tire is available for inspection. Will have tire shop take it off the wheel and inquire to see if they can evaluate what happened. Tire has only been inspected by VDOT employee on site of incident. No sign of warnings or dashboard light before incident until after it blew up which produced a low tire pressure indicator. Has not been reproduced or confirmed by dealer or independent service center. Safety was put in risk to driver and other drivers on highway going highway speed. Was able to control car to a stop. Jeeps are at higher risk of rolling over. Luckily nobody was hurt and no damage to vehicle other than the Tire.

The contact owns a 2013 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the air bag warning light illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the clockspring had failed and needed to be replaced. The vehicle was then taken to the dealer, where the clockspring was replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 99,000.

Abs light illuminated on dash causing loss of power

When driving approximately 45 mph and above the entire car starts to violently shake. I don't know what part causes this problem. I've heard it could be : steering damper, ball joints, tie rods, track bar, front suspension damper cause this. IDK. Until I can afford to take it to a service shop and get it checked and repaired, it sits parked because I'm afraid to drive it. This started about a month ago. Jeep (Stellantis) should be recalling and repairing ALL Wranglers with this problem not just newer models. My car has LOW miles but somehow got excluded from the lawsuit settlement apparently which is going by model years. This is a safety issue.

Fuel supply line going to the engine leaking gas directly onto engine. I started smelling gas and upon inspection found the leak. I googled it and found numerous links with people having the same issue. Definitely poses a safety hazard.

The Fuel Supply Tube part #68141849AD cracked, causing fuel to leak into the engine bay when the car was started. The entire cabin filled with gas fumes so intensely my eyes would water.

The tie rod (steering) randomly disconnected causing loss of steering at 10mph.

The car just shuts off without warning while driving. We’ve had this car for 6 months and had to put in the shop 4 times on different occasions without a resolution. This causes a major safety risk which could lead to a catastrophic accident. This has not been inspected by the manufacturer as of yet.

Intake air temperature sensor falls out of housing when accelerating. Second time this has happened for the same reason.

The contact owns a 2013 Jeep Wrangler. The contact stated that while driving at highway speeds, the check engine and traction control warning lights suddenly illuminated, and the vehicle went into LIMP Mode and decelerated to under 45 MPH. The vehicle was taken to the local dealer who replaced the cylinder head oil plugs, but the failure persisted. The vehicle was later taken to a second dealer who diagnosed that the engine had experienced low compression leak and multiple misfires. The contact was informed that the cylinder head, engine valves, and springs needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure and informed the contact that that a VIN was not included in the Extended Coverage for the failure. The failure mileage was 57,000.

Instrument airbag warning light

At around 85k miles the vehicle began developing a loud tick. It appears every vehicle with this motor or similar motor with the same internal Valve Rocker Arms have this problem. This Jeep problem is so bad that the parts are on a 2 month back order and every dealer admits they have a problem. The repair isn't cheap and entails the entire top of the motor to be exposed and virtually rebuilt. For a vehicle with only 85k miles this is a terrible situation that jeep has put their owners in. This is clearly an issue that should be rectified by the manufacturer.

Windshield cracked.

The oil cooling housing. There was sludge around it and the lines from below the jeep ruptured. causing oil to leak all over the transmission bell. This caused smoking and over all engine. My dad a certified ASE mechanic has looked at it multiple times and fixed various components related to the cooling/heating system.

Parking break slips a lot. Started about 30,000 miles now has 49,000. It is a standard transmission & Slips on flat or any incline progressively getting worse.

After having my car checked multiple times because the check engine light wouldn't go off, finally came to find that the Fuel Tank was cracked, my car was leaking gas, and the wires by the tank were all corroded. The car was not in an accident.

The contact owns a 2013 Jeep Wrangler. The contact stated while at a stop light the vehicle started to stall while accelerating. The contact stated that there was no warning light illuminated. The vehicle was taken to an independent mechanic and the crank shaft sensor was replaced, but the failure persisted. The vehicle was taken to the dealer and the contact was notified of the cylinder #2 misfire. The vehicle was not repaired. The manufacturer was contacted and stated that the vehicle was not under recall. The failure mileage was 114,000.

Motor rocker arm failed possibly damaged motor. Engine oil cooler cracked. Leaking oil over my exhaust. Possibly causing fire.

The contact owns a 2013 Jeep Wrangler. The contact stated the driver’s side front seat belt failed to latch securely. The contact stated that the air bag and ABS warning lights were illuminated. The local dealer was contacted, and the contact was informed that the vehicle was not covered under a recall. The vehicle was not diagnosed or repaired. The contact stated the failure was related to NHTSA Campaign Number: 19V680000 (Seat Belts). The manufacturer was not contacted. The approximate failure mileage was 220,000.

When while I’m driving the vehicle will turn off . I already have this situation happened to me so many times while there’s cars next to me or in face of me

Driving on the highway at 75 mph, red lightning bolt light came on dash. Called dealer and they were no help so I unhooked the battery and it cleared. It did this a total of 4 times before I got home. Seems to be a known issue with throttle control system

The high pressure fuel line that is on top of the engine connected to the fuel rail failed. Gas was spraying on the hot engine. This situation could have caused a fire or explosion. I check and jeep recalled 2014 to 2020 for replacement of this fuel line, which is the same line on my jeep. I had to pay a dealer $757 to fix an issue jeep should be responsible.

The contact owns a 2013 Jeep Wrangler. The contact stated that the check engine warning light was illuminated. The contact used a DTC reader and recovered a code for a misfire in cylinder #6. The contact took the vehicle to the dealer and was informed that her vehicle was not under warranty. The manufacturer was also notified of the failure and provided a case number. The contact was also provided the same information as the dealer. The vehicle was repaired by the dealer. The failure mileage was approximately 89,800. The contact has made several calls to customer service submitting claims and denied. The vin number was not included in the service bulletin and the contact believes several vins are missing from the list.

Recently had my traction control and air bag lights illuminate, at the same time my horn quit, steering wheel controls no longer work and cruise control is out. After some research, I am quite sure it's a faulty clock spring

The contact owns a 2013 Jeep Wrangler. The contact stated that the vehicle was overheating while driving. The vehicle was taken to the dealer, where the thermostat was replaced several times. However, the failure persisted. The contact stated that while driving at an undisclosed speed, the check engine warning illuminated and several chimes were heard. The contact veered to the side of the road and noticed that engine oil was leaking onto the ground. The vehicle was towed to the dealer and was diagnosed that the radiator needed to be replaced. The part was replaced; however, the contact stated that upon parking the vehicle, the failure reoccurred and the engine oil leaked out onto the ground. The vehicle was towed to a second dealer, Perkins Motors (1205 Motor City Dr, Colorado Springs, CO 80905) where it was diagnosed that the engine cooler needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 45,000.

The contact owns a 2013 Jeep Wrangler. The contact stated while driving approximately 30 MPH, the contact crashed into the guard rail. There were no warning lights illuminated. The contact exited the vehicle and noticed the steering box shaft was snapped. There were no air bags deployed. There were no injuries or medical treatment on the scene. The police arrived at the scene and contacted a towing service. There were minor damages to the front of the vehicle. There was a police report filed. The vehicle was towed several times; however, ended up at the local independent mechanic. There was an unknown diagnosis. There was a steering box shaft and tie rod end replacement, in addition to an alignment done. The manufacturer was not notified of the failure. The approximate failure mileage was 100,000.

Horn, evic & radio controls on the steering wheel don't work. After waiting 2 months tfor the part, they replaced the evic switch which I was promised controlled the horn & radio too. It didn't fix the horn or any of the other issues. Now the dealer wants to replace the clock spring. There is an existing recall for my model year and years before and after (Safety Recall S40 / NHTSA 16V-288 Airbag Clockspring) but my VIN is not included. Jeep can not explain why I'm not included and said my airbag may or may not work. Any help is appreciated.

My airbag dash light is illuminated. I took it to Park Jeep and the error code suggests that it is the clockspring that should be replaced. - I bought a "legally imported from Canada" 2013 Jeep Wrangler from a large US non-Jeep dealer in 2016. It had 55k miles so it would have been out of warranty. Recently, I had the pab recall work done at a local Jeep dealership. About a month later, my airbag light started coming on intermittently. Because of the timing of the recall work, I went back to that dealership to have them diagnose/see if they were the cause/etc.. They diagnosed it as needing the clockspring. I have been told by two local Jeep dealerships and the folks at 1-877-amjeep that even though the extended warranty on the clockspring applies to ALL NAFTA market vehicles, they wont fix it under warranty. I was actually told, "...the warranty it didn't have at the time it crossed into the US was voided, thus nullifying any future extended warranty that could would have covered other parts." FCA did this extended warranty nonsense to avoid a recall, and if they arent honoring the extended warranty, then there ought to be a recall on the clockspring. MY airbag is NON functioning due to a manufacturing defect and FCA wont fix it. I cannot be the only person that is adversely affected by this.

Air bag light keeps coming on and off while driving . none stop digging....can not seem to Find the problem other them air bags may not work properly

DRIVING THIS JEEP HIT A BUMP JEEP GOES INTO A DEATH WABBLE.

ABS and check engine light. I am a rural mail carrier, because my ABS light is on it causes my jeep to not accelerate pulling away from mailboxes therefore putting myself and other drivers at risk. The problem has been reproduced at the dealer. Warning lights illuminated at 19687 miles and are still on to this day, no resolution from Jeep. Jeep engineer came to dealership and could not say what was wrong with vehicle.

My vehicle suddenly stops running as I'm driving down the road. This is an reoccurring problem that happens every few days. This does not issue a code nor does the check engine light come on. There is no rhyme or reason to the issue. Electrical does not go out only the ability to push the gas pedal. I have to pull over and turn off the jeep. It comes back on and runs after waiting 10 minutes. This is a hazard and can cause a wreck. It's an common problem with Jeeps as reported on the forums.

For the past 2 years my Jeep has been stalling a lot, have taken it to 2 mechanics and 2 times to the dealer. None of them know what’s going on because there’s no light coming on, except for the first time it happened the ETC light came on but went away a few minutes later.

When driving down the road, the Jeep stops running. This is very dangerous and happens while driving at 55 mph. I’ve taken it to a mechanic and it will not throw a code. We’ve replaced the fuel pump, ignition, battery and alternator. Reading the forums and other online resources shows this is a common problem with multiple solutions. Jeep should recall any parts identified with this issue and be able to help correct this known issue. This is very unsafe. I do not have the money to spend and have no reliable transportation for employment. This has been such a hardship during such trying economic times.

Car surges at times when braking. Increased brake pressure to stop vehicle causes engine to accelerate rapidly when pressing hard to stop vehicle. Dangerous situation. This has happened numerous times when trying to stop at a traffic signal.

Wednesday may 11th approximately 5pm. Was sunny and dry. Turned out of mcdonalds driveway. All of a sudden my brake pedal went to the floor. There was very slight pressure just before it bottomed out. I was lucky no one was in front of me. I could not stop. No dash lights came on. I coasted to stop at gas station. While I waited for a tow truck I started car to move into a better spot. Using parking brake. I then just started pumping brakes. And all of a sudden pressure came back and brakes worked as normal. I immediately towed jeep to dealership. They could not recreate the issue. Everything works fine.

The oil filter housing assembly was found to be cracked during a routine oil change. The oil could leak into the transmission and eventually catch fire. A mechanic has confirmed this is the issue. It will cost approximately $800 to repair. The mechanic indicated he has seen this in the majority of Jeep Wranglers he has serviced and he doesn't understand why a recall has not been issued on this part. This part is made of plastic and can easily crack.

The contact owns a 2013 Jeep Wrangler. The contact stated that the vehicle was running rough. Additionally, while the brake pedal was depressed, the vehicle was slow to respond. There were no warning lights illuminated. The vehicle was taken to an independent mechanic who informed the contact that the caliper had seized, and that the ball joint and K-bar needed to be replaced. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure but no additional assistance was provided. The failure mileage was approximately 20,000.

The contact owns a 2013 Jeep Wrangler. The contact stated while driving approximately 45 MPH, the horn button failed to operate and the steering wheel was difficult to turn. Additionally, the air bag warning light was illuminated. The contact was able to continue driving to his residence. The vehicle was not diagnosed or repaired. A dealer was not contacted. The manufacturer had been informed of the failure. The failure mileage was approximately 69,120.

I own a 2013 Wrangler Unlimited. Since new, the parking brake has been ever-more-difficult to engage. On October 26, I was using the Jeep around my property and had to exit the vehicle while in neutral (auto transmission) and attempted to engage the parking brake. If the handle is pulled slowly, SOMETIMES the brake engages enough to hold. In this particular instance, I pulled the handle slowly, felt some resistance to indicate the brake engaged, and exited the vehicle. The brake then relieved enough pressure to allow the vehicle to roll back into a hole form where a stump had been. Fortunately I was not injured and the Jeep did not collide with anything. This emphasized to me a previously-known safety issue with the product. The design of the brake lever is supposed to be self-adjusting, however in reality, the clutch mechanism to do this allows slippage to the point where the handle hits the backstop prior to engaging the brakes on many Wrangler JKs that are only a few years old. This is a well documented problem in JK forums and many owners have created workarounds to force the mechanism to maintain tension on the parking brake cables. I have not done this to mine, and consequentially have not had a reliably functioning for years. For obvious reasons, this flaw in the parking brake design (especially on vehicles offered with manual transmissions puts public safety at risk. Ilderton Chrysler Jeep Dodge in Winston Salem failed this vehicle on safety inspection in 2020 as a re

The contact owns a 2013 Jeep Wrangler. The contact stated that the check engine warning light was illuminated. The vehicle was taken to an independent mechanic who informed the contact about TSB: 09002-14. The contact was referred to a dealer. The vehicle was taken to the local dealer and diagnosed that the #6-cylinder head needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure but, no further assistance was provided. The failure mileage was approximately 116,000. Consumer stated he had to pay to have the work done even though there is a service bulletin put out by Jeep referring to this problem specifically.

It the oil cooler ...its made of plastic I have only had my jeep for 6 months and am about to have this part replaced for the third time..AND IT NOT COVERED ON MY EXTENDED WARRANTY..800.00 EACH TIME..IM CERTAIN IM NOT THE ONLY ONE ..YOU GUYS NEED TO FIX THIS ..I CANNOT AFFORD TO KEEP CHANGING THIS AND RENTING CARS AND SUCH...SOMETHING NEEDS TO BE DONE ABOUT THIS PART ASAP. I will send a copy of my bill tomorrow