2018 Ford Fusion complaints

My Engine is on my car will not go over 25 miles and if it does it shakes and I place the car in park or shut it off u can hear like water sound coming from the engine were it’s seems as if it was boiling

Rear seatbelt driver side seat belt does not click or buckle at all. Nothing is stuck in it and it has never buckled as long as I’ve had the car

Shift actuator wouldn’t go into gear I was stranded a few times had to be towed twice. I’ve found a plastic bushing that showed a $4.00 part could be responsible. Deadly for us disabled Vietnam veterans . I can’t walk. Maine has 200 vehicles with the same issues nationwide who knows supposedly the actuator will not be made by ford motors until February 2026. I’m 76 years old this is a hazard I can’t afford to buy another car. Please help us. Or get stranded in the middle of nowhere freezing cold Thank you

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle started shuddering violently, hesitated, and failed to accelerate to approximately 35 MPH. The check engine warning light was flashing. The contact related the failure to the Customer Satisfaction Program: 21N12. The vehicle was towed to the local dealer, where it was diagnosed with coolant intrusion into the cylinders. The dealer informed the contact that the engine small block needed to be replaced, but a full engine replacement was recommended. The vehicle was not repaired. The manufacturer was contacted and filed a complaint. The manufacturer advised the contact that a future report would be issued. The failure mileage was approximately 100,000.

The contact owns a 2018 Ford Fusion. The contact stated that while reversing, the back-over prevention camera displayed a black screen. Several minutes later, the message "Contact the Dealer" was displayed. The vehicle was taken to the dealer to be diagnosed, and the contact was informed that the VIN was not under recall. The dealer had not diagnosed or repaired the vehicle. The dealer referred the contact to the NHTSA Hotline to report the failure. The manufacturer was not notified of the failure. The failure mileage was approximately 88,000.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle was running rough, jerking, and shaking. The transmission and coolant temperature warning lights were illuminated. The message "Engine Overheating - Reduced Power" was displayed, and the vehicle went into LIMP Mode. The contact pulled over and had the vehicle towed to the residence. The vehicle was later towed to an independent mechanic, who determined that there was coolant intrusion in the engine, a blown head gasket, and a cracked engine block. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 148,000.

Car started running rough then white smoke was coming out the exhaust. Took it in to have it checked out by Ford and they said it was coolant intrusion into the cylinders. Now they want $9,000 to replace an engine that has less than 60,000 miles. I see online that this is not new and definitely a design flaw with this engine and many others.

What component or system failed or malfunctioned, and is it available for inspection upon request? The APIM (Accessory Protocol Interface Module) appears to have failed. The vehicle's infotainment/play screen is completely blank and unresponsive. This module controls key systems including climate control, navigation, hands-free calling, and the backup camera. The component is available for inspection if needed. How was your safety or the safety of others put at risk? This failure compromises several safety-critical functions. I am unable to adjust climate settings, use GPS navigation, make hands-free emergency calls, or see through the backup camera. These features are essential for safe driving, especially in adverse weather or while reversing. Has the problem been reproduced or confirmed by a dealer or independent service center? Not yet confirmed by a dealer, but the issue has been consistent. I have attempted both soft and hard resets, and verified the fuses are good. All symptoms point to an APIM failure. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No formal inspection has been done by the manufacturer, police, or insurance. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? There were no warning lamps or messages. The issue started intermittently about two months ago. Resets worked temporarily, but the screen is now completely unre

Engine replaced due to flaw in design. I had my 60,000-mile service done and after it was completed, I started having serious issues with my vehicle. Kept getting check engine light cylinder 2 misfire. I took my Fusion back to the dealership, and they advised me that my engine had to be replaced. Apparently when they put my vehicle under pressure during the service it caused the coolant to leak into my engine. I have researched this and found many complaints with the same problem. Unfortunately, the owners of the other Fusions (like me) found out their vehicle was no longer under warranty, and they had to foot the entire bill. Luckly for me, I had purchased the Ford Extended Warranty, and my out-pocket pocket is $100. I was told by the dealership that Ford is aware of this issue but has not issued a recall. My service advisor was absolutely shocked when Ford authorized the necessary repairs in a couple hours berceuse it normally takes a few days to get authorization. I have owned this car since it was new and have always kept up with the required maintenance. They gave me a rental vehicle and said it would be about 7 days before the repairs are completed.

Went to back up to park . The shifter would not properly work kept going back to park .I couldn't get it into neutral to push it. No warnings. Had to 1st pay for towing from where it happened to a parking space. Then called roadside service to take it to Bay Lincoln in Panama Beach.i will send the results from dealership. It could of been real serious and caused a bad accident maybe even death. I know ford had a recall on a earlier model fusion for shifter cable. If it's the same issue I want reimbursement.

Battery Energy Control Module (BECM) malfunction. Causing sluggish response when attempting to accelerate which has nearly caused an accident on multiple occasions. Other vehicles near the date of manufacture of this vehicle are reported having the same symptoms including potential for fire. There is a recall on similar vehicles: Fusion Energi Recall Issued: 2019-2020 - BECM Fire Risk (NHTSA: 23V440, Ford: 23S33) NHTSA Reference: NEF-107DM 23V-440 The date range of vehicles affected most likely needs to be modified to include vehicles manufactured earlier than December 2017. My vehicle, in particular, was manufactured in August 2017 and exhibits the same BECM issue, however, is not currently included in the recall.

The contact owns a 2018 Ford Fusion. The contact stated that upon starting the vehicle, there was an abnormal rattling sound coming from the engine with white smoke coming from the exhaust system, with the check engine warning light illuminated. Additionally, the message “Service Vehicle Soon” was displayed. The vehicle was taken to a local dealer, where it was diagnosed, and the contact was informed that the engine was faulty due to coolant intrusion. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 84,112.

Coolant is leaking into the cylinders and causing overheating and no start.

The contact owns a 2018 Ford Fusion. The contact stated that the vehicle was idling roughly with the check engine warning light illuminated. The vehicle was taken to the dealer, who suggested that the spark plugs be replaced and a tune-up be performed based on the mileage. The dealer performed the spark plug replacement and tune-up, and the check engine warning light was no longer illuminated; however, the vehicle was still idling roughly. The vehicle was returned to the dealer, who diagnosed the vehicle with coolant intrusion into the engine. The contact was informed that the engine had failed and needed to be replaced. The dealer diagnosed the vehicle and determined that the rear brakes and rear brake rotors needed to be replaced due to a brake fluid leak. The vehicle was not repaired. The contact was informed of NHTSA Campaign Number: 23V162000 (Service Brakes, Hydraulic); however, the VIN was not included. The vehicle was not repaired. The manufacturer was informed of the failure and opened a case. The manufacturer informed the contact that the VIN was not under recall or special programs for the repair. The failure mileage was approximately 73,000.

I would like to respectfully request that my 2018 Ford Fusion, with the 1.5L EcoBoost engine, be considered for inclusion in the customer satisfaction programs related to the engine issues I'm experiencing. Despite my vehicle not being initially listed, the problems I've encountered, including the diagnostic trouble code P0302 and the coolant leak into cylinder #2, suggest that it may be suffering from a similar defect or design flaw that the program aims to address. Given the safety risks associated with the current condition of my vehicle, I believe it would be fair and reasonable to include it in the program and provide the necessary repairs or replacements to ensure the vehicle is safe to operate. I would appreciate your assistance in facilitating this process and exploring options for resolving this issue in a manner consistent with the treatment of similar vehicles.

The contact owns a 2018 Ford Fusion. The contact stated that after the engine was replaced, there was an abnormally loud banging sound coming from the engine compartment. The vehicle was taken back to the local dealer, who diagnosed the vehicle with a cracked engine flex plate. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 59,851.

At approximately 67,180 miles, a Ford dealership performed a multi-point inspection on my 2018 Ford Fusion SE with the 1.5L EcoBoost engine due to a check engine light on. The Ford dealership diagnosed the vehicle with a coolant intrusion into cylinder 2. The Ford dealership recommended the replacement of the short block and gasket kit, with an estimated repair cost of $7,465. This type of issue diagnosed for my vehicle is a known failure issue for 1.5L Ford EcoBoost engines documented in Customer Satisfaction Program 21N12, which covers coolant intrusion and engine damage in this engine type. Despite the Ford dealership diagnosis of my vehicle matching what is described in Customer Satisfaction Program 21N12, I was informed that my vehicle is not eligible. The Coolant intrusion into cylinder 2 is an issue that poses a safety risk due to engine misfires, stalling, overheating, and possible sudden loss of engine power while driving. In my case, my vehicle has become unreliable and unsafe for regular driving. A Ford dealership inspected the vehicle, confirmed and documented the issue, and the repair quote, diagnostic report and diagnostic payment receipt are available upon request. Ford has declined assistance despite the vehicle’s low mileage and clear alignment with known engine defects. I mailed a formal appeal letter to Ford Motor Company and I am filing a complaint with my state attorney general. This widespread issue affects customer safety, and vehicle safety standards a

Coolant intrusive. New motor needed

The contact owns a 2018 Ford Fusion. The contact stated that while driving out of the driveway at 5 MPH, the engine light illuminated. The contact stated that the vehicle was difficult to start. The contact stated that the failure was like Customer Satisfaction Program: 21N12. The vehicle was taken to the local dealer for an oil change, and unknown engine repairs were completed. The vehicle was repaired, but the failure recurred. The vehicle was taken back to the local dealer, and it was determined that the engine needed to be replaced. The vehicle was not repaired. The dealer referred the contact to the manufacturer for assistance. The manufacturer was contacted and the referred the contact to the NHTSA Hotline. The manufacturer declined financial assistance, and stated that the issue would be escalated to the negative feedback department. The failure mileage was approximately 69,000.

The car issued no warning, lights or messages prior to the damage. My [XXX] son was driving and the car started shaking which really scared him as he’s a new driver. I would say the safety of him and other drivers on the road were definitely put in danger. The vehicle has been inspected by a Ford dealership. They stated it had a broken flex plate and short block. Broken Flexplate; Diagnostic $210.00 Parts $1,345.86 (Flexplate, transmission fluid pump, filter, one time use parts) Labor $2,600.00 ($200.00 x 13.0hrs) Sales Tax $125.84 Total $4,281.70 Short Block replacement; Diagnostic $145.00 Parts $2,193.64 (Short block engine/kit, spark plugs, one time use parts) Labor $4,480.00 ($200.00 x 22.4hrs) Alignment $159.95 Sales Tax $205.11 Total $7,183.70 Tow Bill $140.00 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Shifter cable bushing degraded and fell off. Causing a condition where the car could not be shifted into or out of gear, and car applied park brake as a safety precaution and could not be disabled until the shifter was manually put back into park by mechanic. This bushing has been under recall for other year fusions but has not been extended to this one. Research on forums shows this is a very common problem. Could be a real safety issue if car cannot be shifted and it needs to be driven away in an emergency. This part should not fail in this short of time, it is made of inferior materials and does not last. No warnings given prior, part fails catastrophically.

My Vehicle was found to have a coolant intrusion. There is a know defect on these vehicles (1.5 / 2L) Ford engine. There was a hairline crack in 2 of the cylinders, which causes coolant to leak thoroughout the engine. My safety was put at risk as this issue causes the vehicles engine to overheat at an unsafe rate. 2 separate dealers found this issue CBA and Autonation Ford. Fidelity Warranty Services inspected the vehicle to see what would be covered. they appeared about 2 weeks prior but would disappear. It finally came back but was extremely repetitive

Engine light came on got it diagnosed said it was misfiring in cylinder 2. spark plugs and coil needed to be changed. Changed all spark plugs and coil and the engine light is still on and saying the same thing. Doesn’t crank right. Coolant going into engine. My vehicle only has 32,000 miles. Seems to be a know problem but ford will not do anything. Saying I need a new motor.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle briefly began to shake violently before returning to normal functionality. The check engine warning light was illuminated. The vehicle was taken to the dealer, who determined that coolant intrusion into various cylinders had resulted in damages to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 130,000.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at various speeds, there was white smoke coming from the rear exhaust. The check engine warning light was illuminated. The vehicle was taken to a local dealer, where it was diagnosed with coolant intrusion into cylinder #3, low coolant, and an overheated engine. The vehicle was not repaired due to the cost. The contact related the failure to TSB: 19-2208. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 76,000.

Known issue with 2013 Models through 2019, Sunroon leaks under heavy rain even if the Drains are cleaned and cleared. I spoke with Ford and they said it is not their issue since there is no recall. This has been posted under multiple site that there are hundreds of people effected by this.

The contact owns a 2018 Ford Fusion. The contact stated that the check engine warning light was displayed on the instrument panel. The vehicle was taken to an independent mechanic, where a code reader determined that there was a misfire in cylinders #1 and #3. The vehicle was taken to a dealer, where the engine misfires were confirmed, and the engine's long block needed to be replaced. Upon investigation, the contact discovered Technical Service Bulletin: 22-2229; however, the vehicle was not covered under the TSB. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline to file a complaint. The failure mileage was 88,300.

Coolant intrusion, coolant and oil is mixing causing my car to run hot. Engine light keeps coming on, repairs to multiple pumps replaced, water pump replaced, spark plugs replaced, radiator replaced, thermostat replaced. Ford dealership tried replacing all the above vehicle is still running hot. Now claiming I need a new engine.

The contact owns a 2018 Ford Fusion. The contact stated that after starting the vehicle, the gear shifter could not immediately be shifted out of park(P). The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The failure mileage was unknown.

My dashboard cover is peeling, it is made from leather, it is interfering with the heads up diplat, automatic lighting system and forward braking safety components, I have brought this to Ford to try to have them repair it dash but I am always told that the piece is considered trim and is not under warranty, I have also checked with Ford Fusion message boards and it seems there is a TSB on the exact 2017 model. Ford has basically told me to have it repaired at a automobile leather restoration company, I have gone to 2 different repair shops and was told it can’t be repaired it has to be replaced. I called Ford Corporation customer service and because they have no outstanding recalls on my vehicle they told me to report this to you

Engine failure due to coolant leaking into cylinders. This is a known issue. Also Ford has issued a bulletin on this. but no recall yet! I still own 10k on my car and now a blown engine.

Leaking coolant

The contact owns a 2018 Ford Fusion. The contact stated that the low coolant warning light had illuminated prematurely. Upon inspecting the vehicle, the contact was unable to find a coolant leak. Additionally, the contact stated that the vehicle overheated while driving, which required the contact to pull over temporarily and to resume driving after the vehicle had cooled down. The vehicle was taken to a certified mechanic, where it was diagnosed that there was coolant intrusion into the engine, which caused the engine to slowly fail. The vehicle was not repaired. The dealer was notified of the failure. The contact related the failure to an unknown recall. The manufacturer was informed of the failure and confirmed that the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline to file a safety complaint. The failure mileage was approximately 150,000.

UNKNOWN

The contact owns a 2018 Ford Fusion. The contact stated that upon starting the vehicle, the vehicle started shuddering. The contact stated that the check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed that there was coolant leaking into the cylinder. The mechanic informed the contact that the engine needed to be replaced. The contact called the local dealer for parts; however, the vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the VIN was not under recall for the failure. The failure mileage was approximately 91,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving 30 MPH and depressing the accelerator pedal, the vehicle hesitated and stalled. There was no warning light illuminated. A dealer was contacted. The vehicle was taken to the dealer where it was diagnosed and determined that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and transferred the contact to the NHTSA Hotline to report the failure. The approximate failure mileage was 72,000.

Coolant intrusion into engine cylinder #2 causing misfire and low coolant levels and overheating and stalling. See Ford TSB 22-2229

The engine cooling system and engine block failed due to coolant intrusion into the engine cylinders. This issue has been diagnosed by an independent mechanic and is available for inspection upon request. Yes, the problem has been confirmed by an independent service center, which diagnosed coolant intrusion into the engine block, a known issue on this engine. The shop recommended full engine replacement and stated this is a common failure in this vehicle. Not yet by the manufacturer, police, or insurance. The issue has only been inspected by a certified independent mechanic. Yes, a check engine light appeared along with a coolant temperature warning message. The vehicle also began to idle roughly, produce heavy exhaust, and consume coolant. These symptoms began appearing shortly before diagnosis in June 2025. I own a 2018 Ford Fusion with a 2.0L EcoBoost engine. The vehicle recently began experiencing coolant loss, heavy exhaust, and check engine alerts. A certified mechanic confirmed that coolant has intruded into the engine block, causing internal misfires and risk of major engine failure. I was told this is a common and well-documented issue with this engine design, yet there has been no official recall from Ford despite similar problems affecting other models (referenced in Ford TSB 19-2208). The mechanic has recommended a full engine replacement with an estimated cost of $13,000. This is a serious safety concern, as the engine can overheat, stall, or seize while driving.

2018 fusion AWD Titanium, less than 70,000 miles, no warning, no reason. Driving 70mph on interstate when low coolant light comes on, check engine light comes on, car starts losing power and running rough, finally full stall in middle of freeway with catastrophic engine failure due to coolant leak and faulty design. Car was not low on any fluids as they were checked everyday before it was driven. This could have gotten me and my children killed and quite frankly I dont know how it didn't. I bought this car with 44k miles on it. Drove it less than 30k miles and had catastrophic engine failure. This was AFTER I had it in the shop several times for crank shaft position sensor, wouldn't start, and several other problems. The car was taken care of and in immaculate condition. Ford knew these engines would fail prematurely and continued to manufacture them and sell them.

The contact owns a 2018 Ford Fusion. The contact stated while the vehicle was parked, the vehicle shuddered. The contact stated that the check engine warning light was illuminated, and the message "Coolant Overheating" was displayed on the instrument panel. The failure had occurred on several occasions. The vehicle was taken to a dealer where it was diagnosed and determined that there was coolant intrusion into the cylinders, and that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 90,000.

Transmission shift linkage bushing failure and torque converter shudder shudder been on going problem for approximately 12months90000

The contact owns a 2018 Ford Fusion. The contact stated that while driving at various speeds, the vehicle shuddered upon depression of the accelerator pedal. The contact stated that while at a complete stop, there was an abnormal popping sound coming from the vehicle while depressing the accelerator pedal. The failure persisted, and the contact stated that the steering wheel was loose while operating the vehicle. The contact stated that the traction control warning light flashed on the instrument panel during one of the failures. The vehicle was not yet diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that there were no recalls on the VIN related to the failure of the vehicle. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 41,000.

Vehicle has a loss of coolant but no visible leaks think may be due to a engine leak.

The contact owns a 2018 Ford Fusion. The contact stated that while driving 5 MPH, the contact heard a sound like running water coming from the engine. The contact stated that the check engine warning light was illuminated. An independent mechanic was contacted. The vehicle was taken to the independent mechanic, where it was diagnosed that there was coolant leaking into the engine, and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact related to the failure of the Customer Satisfaction Program: 19B37 (Engine - Powertrain Control Module Reprogramming). The contact was transferred to the NHTSA Hotline to report the failure. The approximate failure mileage was 102,000.

The contact owns a 2018 Ford Fusion. The contact stated that while his wife was driving at an undisclosed speed, there was an abnormal sound coming from the fuel tank. The check engine warning light was illuminated. The vehicle was taken to the dealer and was diagnosed with a coolant sensor failure. The coolant sensor was replaced; however, the failure persisted. The vehicle was taken to an independent mechanic who replaced the coolant sensor. The contact stated that recently, the failure had recurred. The vehicle was taken to a different independent mechanic, who diagnosed the vehicle and determined that the engine block was cracked and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The contact related to the failure to the Customer Satisfaction Program: 21N12; however, the vehicle was not included. The failure mileage was approximately 115,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving approximately 45 MPH, the message "Engine Overheating" was displayed on the instrument panel. The contact stated that the check engine warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that there was internal coolant intrusion into the cylinders, and that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 86,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the engine overheated and the check engine warning light illuminated. In addition, the contact noticed white smoke coming from the exhaust, and the engine was running abnormally rough. The vehicle was taken to the dealer, where it was diagnosed with coolant intrusion in cylinder #1, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 115,000.

A frozen rear-view camera display image while in reverse

My vehicle has had the check engine light come on intermittently. I took a look under the hood to see if I could spot any issues. The only issue seen was the coolant level was low. After refilling the coolant and a short time driving, perhaps 50-60 miles, the light went out. Then the light came back on a couple days later. Without making any changes the light went out a couple days later. It has done this several times and I thought it may be a faulty sensor or something. I have recently taken it to the dealership for a tune-up, emissions test, multipoint inspection and a transmission flush. I informed the service person that the check engine light will come on and go out and the only thing I have done to the vehicle was add coolant. He suggested the complimentary diagnostic to further identify the issue. During the diagnostic process the auto tech discovered that the coolant has been leaking into the number 2 cylinder. This is the reason for both the fluid loss and the check engine light. From my understanding this is a known issue with my vehicles engine type and has been for some time now. The only fix is to replace the engine. My overall issue is that the safety light (CEL) will say that there is an issue and then it goes away signifying the issue is resolved. The potential hazards of this could possibly lead to an individual unknowingly putting themselves and others at risk with an engine that is prepped for failure. An engine that could overheat, catch fire, throw a rod

At 68,000 miles, the transmission began experiencing symptoms of a failed transmission. I took it to the dealer and they confirmed that there was a CONCERN HARSH SHIFT ON 3RD GEAR AND DIAGNOSE DIRECT DRUM CAUSING CUST CONCERN AND SHUDDER CONCERN TORQUE CONVERTER. This diagnosis caused the vehicle to hard shift everytime i would take off and often time cause a kick on the transmission. Because of this, the rear main seal of the engine also gave out prematurely. While driving on the freeway, the engine began leaking oil suddenly from the rear main seal causing the entire bottom of the engine to get soaked with oil. This also caused the oil to fall in to the brake pads and rotors. While driving on the freeway, i lost braking power and could not stop safely. I had to pull to the shoulder and attempt to stop the vehicle. Fortunatelly, there were no cars on the soulder and was able to stop the vehicle. This is where i discovered the vehicle full of oil in the bottom of the vehicle along with the brake pads and rotors. The vehicle was towed to the house about 130 miles. Once discovered, it was taken to Sunrise Ford where they discovered all of the issues. The service tech told me that it is a common problem for those transmissions to fail prematurely and cause other problems. This is a safety issue because after 7 years of the vehicle being on the road with under 100k miles, it is posing a safety hazard not only for the customers but also the public. Please investigate the transmiss