2022 Ford Bronco complaints

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

The Molded-In-Color (MIC) hard top shows signs of delamination and cracking on the exterior skin of the roof panel. Models from the same production year were called under NHTSA Recall No.: 26V299. My vehicle was not included on this recall. I have attempted to have Ford inspect the issue and have refused since it is out of warranty. I am concerned that the delaminating sections will detach while driving.

I took my vehicle to the local Ford dealership for the remedy for recall Ford 25S01 on Feb 2, 2026. During the inspection, it was found that the part affected was damaged and the dealership sent photos to Ford. After that, I haven't received any guidance from Ford or the dealership. Since the invoice I received indicated that there was a weld crack in one of the absorbers, I assume that the recall should repair this as a safety concern, but I haven't received any proactive communication from Ford or the dealership. I have contacted the dealership twice since February but I have not received any callback. I am concerned that this is a safety issue and Ford hasn't done anything to correct this since they found out about the issue in February.

Complete clutch failure at 39,000 miles. Unable to shift or safely restart vehicle once stopped. Clutch Hydraulic line came completely apart. Ford part number MB3Z-7A512-A. Failure verified by independent SAE certified mechanic. Note: Clutch and Brakes feed from the same reservoir, so loss of clutch hydraulic fluid also impacts entire braking system.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

The contact owns a 2022 FORD BRONCO. The contact became aware that the VIN was included in NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline) through a VIN search; however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Additionally, the contact stated that the rearview and front view cameras were intermittently inoperable. The contact related the failure to NHTSA Campaign Number: 26V124000 (Back Over Prevention). The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the issue. The failure mileage was approximately 8,600.

The contact owns a 2022 Ford Bronco. A warning light restraint indicator lamp warning saying airbag system may not deploy properly, vehicle impact sensors affecting airbag, received warning indicator on the instrument panel saying vehicle should not be driven until remedied and should be taken to dealer. The vehicle was taken to the dealer where it was not diagnosed or repaired but the dealer advised does not know how to resolve the issue, The manufacturer was not notified of the issue. The approximate failure mileage was 14,440.

I drive a Standard ‘22 Bronco. Only E-brake works for parking brake when in parking lots and such. My Bronco rolls into oncoming traffic and pedestrians when the e-brake releases. I am former Homeland Security and this unacceptable, as this if my 10th issue with the Ford Bronco! Safety First!

The instrument cluster panel goes black and stays blacked out for driving from startup to shutdown. This does not occur consistently, but it occurs often and unpredictably and is occurring more and more often. Attempted to have dealership fix and they want to replace the instrument cluster panel. This is a safety issue for basic functionality of the vehicle. Ford has had this issue identified during other years of Bronco production but appears unwilling to fix it in all of them.

There has been an SSM release by Ford (SSM 51415) acknowledging that 2021-2022 Bronco vehicles flat towed in neutral may experience inconsistent or unintended ABS (anti-lock brake) module activation while being towed. The ABS module exits sleep mode unexpectedly due to road vibration input during towing, which can cause brake drag or lockup while the vehicle is being flat towed behind a motorhome. This is a safety concern as unexpected braking of the towed vehicle can affect the towing vehicle's stability and control at highway speeds. The vehicle is being operated exactly as documented in the Ford owner's manual, which explicitly supports neutral flat towing. Ford has developed a software update to address this defect but is declining to cover it under warranty or goodwill, instead classifying it as non-covered maintenance. The issue has been confirmed by an authorized Ford dealership who identified SSM 51415 as applicable. A community workaround requiring removal of fuses 28 and 29 to disable the ABS pump has emerged among owners, indicating this is a widespread known issue affecting safety during a manufacturer-approved towing method. Ford should issue a TSB or recall and cover the software correction at no cost to owners.

There has been a Safety recall in the fuel pump for almost a year, with documented known issues existing well before the release and Ford has still yet to make a remedy available.

The contact owns a 2020 Ford Bronco. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed, however, the vehicle failed to accelerate as intended. The check engine warning light illuminated and the engine seized. The contact stated that while attempting to start the vehicle, the vehicle failed to start as intended. The vehicle was towed to the residence. The mobile independent mechanic came to the residence, and the vehicle was diagnosed with a failed low pressure fuel pump. The contact was informed that the low pressure fuel pump needed to be replaced. The vehicle was not repaired. The dealer was made aware of the failure. The contact was informed that the parts were unavailable. The contact received a recall notification, NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline) however the parts were unavailable. The manufacturer was not made aware of the failure. The failure mileage was approximately 25,000.

Noticed that my hardtop was cracking around the rear windows. This is a know issue with Ford and is being replaced under warranty. Unfortunately, my vehicle is outside of the original 3 year 36,000 mile warranty period by just over 6,000 miles that would qualify for replacement. The dealer quoted over $10,000.00 to replace the entire top since all roof panels appear to be affected. This is almost 1/4 the cost of my vehicle on the used market and is unacceptable for a know issue that would normally be replaced under warranty.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V312000( BACK OVER PREVENTION) However, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure

My 2022 Ford Bronco experienced recall 25S75 where fuel pump failed while driving on the freeway outside LA near San Bernardino. Recall was communicated in July of 2025 and no fix available. How long has Ford been building cars? There were no warnings or symptoms prior to failure. This was extremely dangerous for car to stall in the middle of the freeway, not to mention it was 98 degrees outside. I was able to tow my Bronco to a Ford dealership where they confirmed and fixed the recall fuel pump issue.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure.

Truck began scrolling warnings that pre-collision braking, hill start assist, forward collision, adaptive cruise control, and more were all not working. Alerts came out of no where while driving on highway and continued every 30 min to hour of drive time. Cruise control was disabled with this failure. Diagnosed with faulty steering-rack. This has been recalled on other 2022 Ford Broncos, but for some reason our was not included in this recall. This lot was clearly impacted as well. The truck is used for daily driving, does not go off-roading and was not involved in any collision or incident that triggered this, simply driving down the highway. Please let Ford know to expand the recall, our car is not safe to drive and is not inoperable unless we pay for the repair or the recall is expanded. Thank you for your assistance!

On May 7, 2026 while driving approximately 18 mph, my Ford Bronco 2022 Outerbanks experienced a sudden loss of normal braking assist. The brake pedal became stuck in the upright position requiring excessive force to stop the vehicle. When the brake pedal went down the truck rolled to the curb and I put it in park. There was a warning sign on the dash that flashed and went away. I could not see what it was. Luckily there were no bystanders or other cars on the road at the time. I was near an elementary school at the time. This would have caused a crash or worse if there were pedestrians. I turned the truck off and called the tow. At the dealership they diagnosed and confirmed an electronic brake booster (EBB) failure. This EBB failure mirrors a recent recall from Ford affecting 2025 Broncos. The dealership has refused warranty because I am 6 months outside the warranty period even though I only have 29,960 miles. This is not normal wear and tear. The 2025 recall # is 25V488. This EBB recall may also affect previous years such as mine and should be investigated.

The contact owns a 2022 Ford Bronco. The contact stated that while attempting to reverse, the rearview camera became inoperable. The contact stated that the rearview camera image failed to function and the image would appear as blank. The contact received notification of NHTSA Campaign Numbers: 26V124000(Back Over Prevention) and 25V455000 (Fuel System, Gasoline), however, the part to do the recall repair was not yet available. The dealer was contacted. The vehicle was not diagnosed or repaired. The dealer confirmed that the remedy parts were not yet available. The manufacturer was made aware of the failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The approximate failure mileage was 35,000.

The contact owns a 2022 Ford Bronco. The contact stated while reversing, the rear view camera displayed a blank screen. The vehicle was taken to the dealer where the contact was informed that the parts were unavailable. The vehicle was not repaired. In addition, the contact was informed that the parts were not going to be available until July 2026. The contact received a recall notification, NHTSA Campaign Number: 25V455000 (Back Over Prevention) however the parts were unavailable. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 27,800.

The steering is unsafe, my neighbor works at a ford dealership and said it’s the rack, which I also read online that it’s become a common problem, the steering has become very stiff. To the point where I have had to slam on the breaks at curves in the road just to be able to turn into the bend, which has almost caused two incidents.

Vehicle has Surged and stalled randomly, the Crash alert warning appears on screen and starts to stop the vehicle with nothing in front of it, I have asked my Ford Dealer to remedy the recalls as I have paid over $50,000 for the vehicle and they tell me sorry there are no fixes, I tried to trade it in, and they said they cannot because they have a no sale enforcement on the Bronco and they said if they took it in trade they could not sell it.

Anti lock beake system warning light. Very hard to press brake pedal. Brought immediately to dealership. Was told Brake vacuum hose Part # MB3Z 2420 L. Part is not covered by any warranty standard or extended. Also told this is a known issue SSM 50472. Safety of driver, passengers and public placed in danger.

I was operating the vehicle on the highway and the steering locked up. I had no indication that this was going to happen. It would not turn and almost caused an accident. I was able to break the steering do to my strength. I was able to limp truck to dealer. Upon inspection they confirmed a faulty / locked up steering shaft. This was not covered by ford. The shaft was replaced and functional now. I have made several attempts to communicate with corporate ford about this safety matter and haven’t been heard from. They have had shaft issues with their f150 trucks also. This issue is a direct result from poor manufacturing and is a real safety issue. This should never happen with a vehicle that is only a few years old with not that many miles.I have saved the part for inspection and looking for some assistance. Thanks you.

The contact owns a 2022 Ford Bronco. The contact stated that while driving approximately 60 MPH, the accelerator pedal was depressed and the brakes unintendedly engaged. The contact stated that the brakes were intermittently engaged even though the brake pedal was not depressed. The message "Check Braking System" was displayed on the instrument panel. The failure had occurred several times. The contact researched and was made aware of NHTSA Campaign Numbers: 25V488000 (Service Brakes, Hydraulic), 25V823000 (Service Brakes, Hydraulic); however, the VIN was not included in the recalls. The vehicle was taken to a dealer to be diagnosed; however, the dealer stated that without a fault code, the vehicle could not be diagnosed. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that dealers were independent. No additional assistance was provided. The failure mileage was approximately 4,000.

Jul 08,2025 Manufacturer Recall Number25S75 NHTSA Recall Number25V455 Recall StatusRecall Incomplete, remedy not yet available Summary ON YOUR VEHICLE, IT IS POSSIBLE TO HAVE A LOSS OF FUEL PRESSURE AND FLOW FROM THE FUEL TANK DUE TO FUEL PUMP FAILURE. THIS CAN CAUSE A LACK OF FUEL DELIVERY TO THE ENGINE AND RESULT IN AN ENGINE STALL WHILE DRIVING. Safety Risk AN ENGINE STALL WHILE DRIVING INCREASES THE RISK OF A CRASH. Remedy FORD MOTOR COMPANY IS STILL ACTIVELY INVESTIGATING THIS ISSUE AND WORKING TO DEVELOP A REMEDY. WHEN THE REMEDY BECOMES AVAILABLE, FORD MOTOR COMPANY WILL NOTIFY YOU VIA MAIL TO SCHEDULE A SERVICE APPOINTMENT WITH YOUR DEALER FOR REPAIRS TO BE COMPLETED FREE OF CHARGE.

Front Camera sometimes malfunctions and will not display, only black screen. A recall or customer satisfactory program has been issued for rear camera, but not for front Camera. This issue could be dangerous when pulling forward from a parking spot as view is partially obstructed by large hood. The Ford dealership quoted a replacement but failed to fix or replace under warranty.

Vehicle brake pedal is very hard to press, unable to push in until the car engine is running. When driving the brake pedal seems it has more pressure and cannot push it to normal level. On the highway it came up brake safety warning when I was in 4Wheel Auto. The pedal stiffness has been checked and confirmed by AutoNation Service. They stated no Warranty or Recall Notice for this issue. The issue is commonly reported by broncos with 2.3L and is determined to be the Brake Booster Vacuum Line. Statements share similar brake pedal stiffness when engine stopped, and engaged stiffness when in 4 wheel mode or Cruise Control, causing driver to put immense pressure on pedal to have the car brake. Before I pay for the parts and long service this clear safety concern should be looked at.

The contact owns a 2022 Ford Bronco. The contact stated that while operating the vehicle, the back over prevention camera malfunctioned. Additionally, the contact reported that the check engine warning light illuminated; however, the fault light was cleared by the dealer during a service visit. The contact received notification of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE), 25V721000 (SEATS), and 26V124000 (BACK OVER PREVENTION); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was 63,000.

On April 3rd, 2026 my steering started to intermittently lock up on my 2022 Ford Bronco. I immediately took my vehicle to my local dealership where they were able to recreate the problem. The vehicle was also throwing the code U3000:49-8A for steering gear failure. This issue appears to be consistent with the Ford Safety Recall 23S09. There was no warning prior to the issue. There were no warning indicators once the issue began.

The contact owns a 2022 Ford Bronco. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power with several unknown warning lights illuminated. The vehicle was towed to the dealer, where it was diagnosed, and determined that the fuel pump had failed and needed to be replaced. The vehicle was repaired. The contact stated that after the repair, while driving at an undisclosed speed, the vehicle unexpectedly shook and sputtered. There was no warning light illuminated. The contact received notification of NHTSA Campaign Numbers: 25V455000 (Fuel System, Gasoline), 25V721000 (Seats), and 26V124000 (Back Over Prevention); however, the parts to do the recall repairs were not yet available. The dealer was contacted. The vehicle was not diagnosed or repaired. The dealer confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure, and a case was opened. The approximate failure mileage was 35,000.

The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V455000 (Fuel System, Gasoline), 26V124000 (Back Over Prevention), and 25V721000 (Seats); however, the parts to do the recall repairs were not yet available. The contact stated that the infotainment screen intermittently turned blank at start-up, causing the rear-view camera to fail while reversing. The dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 15,000.

The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline) and 25V721000 (Seats); however, the parts to do the recall repairs were not yet available. The dealer was contacted, and the contact was informed that parts were not yet available. The manufacturer was contacted, and the contact was informed that parts were not yet available. The contact had not experienced a failure.

My vehicle is experiencing potential electrical issues which appear to be similar to the same 12-volt battery management failures that are currently recalled in the Bronco Sport models. The "Charging System Service Now" alarm continues to pop up, sometimes every 30 seconds. I am also not able to use my communication and navigation system, and I am not sure if this is related to the same electrical system malfunctions. Furthermore, on three recent occasions, my vehicle stalled while I was pulling out of a street which was on a slight incline, another while I was on a hill in a parking lot, and another while I was reversing and putting my car into 1st gear to drive. During all of these occasions, my vehicle stalled and did not automatically re-start which had me blocking traffic while I turned my vehicle back on. All of these issues have affected the safety of myself and my passengers due to the unexpected stalling as well as electrical power loss, including loss of navigation/communications. It has also resulted in me getting pulled over by law enforcement twice due to swerving while I was looking at the screen when it went black and the other because I was speeding because my Charging System Service alarm went off and I was also unable to determine the speed limit of that road without having my navigation screen working. I believe I have contacted the Ford Dealership regarding the specific loss of the communication and navigation issue and was told they did not have the parts

I would like to update my previous safety concern since both concerns are related to separate recall issues. This concern is related to my vehicle experiencing potential electrical issues which appear to be similar to the same 12-volt battery management failures that are currently recalled in the Bronco Sport models. The "Charging System Service Now" alarm continues to pop up, sometimes every 30 seconds. I have not able to use my communication and navigation system for months now which has caused continuous issues which first started with my gps taking me to a completely different location on several occasions. This has caused me to get lost, be late, and be distracted while trying to fix the navigation error. These electrical issues have affected the safety of myself and my passengers due to the potential for complete electrical power loss, including loss of navigation/communications. It has also resulted in me getting pulled over by law enforcement twice: Once, where I received a warning for failing to use my turn signal when exiting which was the result of my entire screen going black while I was using my GPS and panicked. The second time was for speeding: 1. I was distracted because the Charging System Service alarm popped up on my dashboard. 2. My navigation screen was not working which I what I used to monitor the speed limit and maintain correct speed when the sign was not visible. 3. According to research, this may have affected the accuracy of the speed gun since I d

The contact owns a 2022 Ford Bronco. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power with several unknown warning lights illuminated. The vehicle needed to be towed. The contact was informed that the VIN was included in NHTSA Campaign Numbers: 25V455000 (Fuel System, Gasoline), 25V721000 (Seats), and 26V124000 (Back Over Prevention); however, the parts to do the recall repairs were not yet available. The vehicle was towed to the dealer to be diagnosed, and it was determined that the low-pressure fuel pump had failed and needed to be replaced. The vehicle was not repaired, and the dealer confirmed that the parts were not yet available. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for additional assistance. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The approximate failure mileage was 40,000.

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (FUEL SYSTEM, GASOLINE); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the vehicle was driving roughly, and it stalled several times. The vehicle was taken to the local dealer, and the low-pressure fuel pump was replaced, but the failure persisted. The manufacturer was made aware of the issue. The failure mileage was 5,000.

Getting a cross traffic alert and blind spot alert fault warning every time I drive the car.

My 2022 Ford Bronco (2.7L) currently has an open fuel pump module safety recall with no remedy available. Ford has informed us that there is no fix yet and owners must wait until a future repair becomes available. The dealership attempted to replace the fuel pump in hopes of improving the issue, but the repair did not resolve the problem and the vehicle now performs worse than before. The vehicle cannot be safely driven and is currently sitting in my driveway. Ford has acknowledged the issue under case number [XXX] but stated there is currently nothing they can do until a fix becomes available. This leaves us with a vehicle that cannot be safely operated due to a known safety defect with no available remedy. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The contact stated that upon starting the vehicle, the vehicle sputtered and nearly stalled. The contact turned off and restarted the vehicle; however, the failure persisted. Additionally, the fuel gauge was constantly inaccurate while starting the vehicle and while driving. The contact stated that the fuel gauge read 0 miles or 0 percent while there was fuel in the tank. The check engine warning light was illuminated. The dealer was contacted to schedule an appointment; however, the dealer informed the contact that the part for the recall repair was not yet available. The vehicle was not diagnosed or repaired. The contact stopped driving the vehicle due to safety concerns. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 59,700.

The contact owns a 2022 Ford Bronco. The contact was informed of the NHTSA Campaign Number: 23V165000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact experienced the failure and became aware that the back-over prevention camera had malfunctioned, and a black screen was displayed. The failure mileage was 35,900.

The contact owns a 2022 Ford Bronco. The contact stated that while her husband was driving 65 MPH, the vehicle unintendedly decelerated and jerked abnormally. The driver pulled over to the shoulder of the road and inspected the vehicle. The driver then drove to the dealer, where the vehicle was diagnosed as having a contained fire inside the exhaust pipe. The vehicle remained at the dealer for further diagnostic tests with the assistance of the engineers. The dealer informed the contact that the manufacturer had denied the contact vehicle rental assistance. The vehicle was not yet repaired. The contact stated that with the three recalls, it was unsafe to continue driving the vehicle. The manufacturer was notified of the failure. The failure mileage was approximately 80,000.

I am submitting this complaint regarding an open safety recall on my vehicle, NHTSA Recall 25V721 (Manufacturer Recall 25SB5), which has been active since October 29, 2025. As of today, the recall remains incomplete and the manufacturer states that no remedy or parts are available, with no estimated timeline provided. The recall involves a potential issue where a front seat frame height-adjust pivot bolt may loosen or dislodge, increasing the risk of injury in a crash. According to the manufacturer, this condition may not be identifiable without an incident or collision. My concern is that: 1.The recall has been open for over three months with no interim remedy, inspection protocol, or mitigation guidance offered to owners. 2.The manufacturer has not provided clear written guidance on whether the vehicle is considered safe for continued operation while awaiting the remedy, beyond stating that parts are unavailable. 3.Owners are left in a prolonged state of uncertainty, despite the recall being classified as safety-related. 4.The lack of interim guidance or remedy availability is causing financial and practical hardship, as vehicles with open safety recalls are restricted from certain lawful uses, even when no symptoms are present. I am requesting that NHTSA review whether the manufacturer’s delay in providing a remedy—or interim safety guidance—meets expectations for timely resolution of a safety recall. I am also requesting that NHTSA encourage the manufacturer to provide ei

The contact owns a 2022 Ford Bronco. The contact stated that the front passenger's side seat frame bolt had detached within a week of purchasing the vehicle. The vehicle was taken to a Ford dealer, where the bolt was reinstalled and tightened. Additionally, while driving 5-8 MPH in 4WD Low Mode, the vehicle made a beeping sound and stalled. The contact stated that the engine was chugging. The contact turned off and restarted the vehicle, and the vehicle responded as needed. The contact had stopped driving the vehicle in 4WD Low Mode. The vehicle was not diagnosed or repaired. Additionally, while reversing, the rearview camera displayed a black or blue screen intermittently. The vehicle was not diagnosed or repaired. The contact received notification of NHTSA Campaign Numbers: 25V312000 (Back Over Prevention), 25V455000 (Fuel System, Gasoline), and 25V721000 (Seats); however, the parts to do the recall repairs were not yet available. The dealer was contacted, but the vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was unknown.

The hardtop developed cracks early on during the life of the vehicle. It leaks water. It’s a known issue with Bronco owners with the factory hardtop. Some people have had it replaced more than 3 times due to the same thing continuing to happen.

When braking(going down hill) the Bronco comes to a complete stop and the brakes feel good. But a split second after the full stop, the truck starts to creep forward for about a foot and then you hear a "click noise" and the truck abruptly stops. This is a very scary feeling wondering if your gonna roll into cross traffic. This happens every morning(once every day) and the rest of the day the brakes feel good. This issue has been happening for the last 7 days. I made an appointment with Ford dealer to look at it. Service writer tried looking up any recalls or complaints on this issue and couldn't find anything? On the BroncoG6 forum online, there apparently are other Bronco owners complaining about the same issue. One owner (online) stated that the dealer reprogrammed the ABS system and his truck hasn't repeated the creep anymore. There haven't been any brake, ABS or any warning lamps at all when this happens. This really needs to be resolved before someone get injured.

I believe my vehicle has suffered a cracked/fractured or broken intake valve on cylinder number 4. There is very low compression in that cylinder. I checked it and it only managed to produce 25psi. I inspected the cylinder with a borescope camera and there is no damage or excessive wear to the piston or cylinder bore. They both look pristine with no signs of anything. I could not see either the intake or exhaust valves on my camera. They are the only pieces of the engine I could not inspect that could possible cause a compression issue. It is my understanding that ford is aware of an issue of this happening on some 2.7 Ecoboost engines?

What component or system failed or malfunctioned, and is it available for inspection upon request? - Display for backup camera freezes after putting vehicle in reverse. Yes, it is available for inspection. How was your safety or the safety of others put at risk? - The display freezes when putting the vehicle in revers and the initial image on display of what was behind the vehicle stays the same while moving. If something or someone moves behind the vehicle while moving the image does not update to show that something or someone is now behind the vehicle. Previously recall 23S48 was completed related to the issue but it did not resolve the issue. Vehicle was taken back to the dealer and the dealer informed me that it is a faulty APIM and not the backup camera and is therefore not covered by the recall. This is a significant safety issue and needs remedied regardless of what component needs replaced. Has the problem been reproduced or confirmed by a dealer or independent service center? - Yes Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? - Only by the dealer (Midwest Ford in Hutchinson, KS). Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? - No

REAR WINDOW (REAR FLIP UP OVER TAIL GATE) SPONTANIOUSLY SHATTERED AND REQUIRED FULL REPLACEMENT.

The contact owns a 2022 Ford Bronco. The contact recently purchased the vehicle to use as a rental vehicle. The contact stated that while registering the vehicle with the rental agency, the contact was made aware of the two open recalls. The recall notifications were NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline) and 25V721000 (Seats); however, parts for the recall repairs were not available. The dealer was made aware of the issue. Due to the parts not being available, the contact might have to sell the vehicle. The manufacturer was contacted and informed the contact that the parts were not yet available. The contact had not experienced a failure.