2016 Acura MDX complaints

***THIS IS A RESUBMIT WITH CORRECTED INFORMATION*** I purchased a used 2016 Acura MDX from a family member, and shortly afterward began experiencing a rhythmic metallic knocking noise under load, particularly at low RPMs (e.g., accelerating in low gears or when the engine is bogged). The noise is not present at idle or during coasting, and it closely matches the symptoms described in recall 23V-751, which addresses premature connecting rod bearing wear that may lead to engine failure in certain Honda and Acura vehicles. However, my vehicle’s VIN is not included in the existing recall. The knocking has persisted across several thousand miles and multiple oil changes. I recently inspected the drained oil and found metallic sparkles/particles, which may indicate active bearing wear. There has been no Check Engine Light, and the vehicle has received on-time oil changes using high-quality synthetic oil, with immediate mechanical inspection when the noise first appeared. I know for certain the previous owner maintained the vehicle properly, as he is a family member and I occasionally helped with maintenance myself. Based on the symptom pattern, operating conditions, and consistency with the failure mode described in 23V-751, I believe this vehicle may be affected by the same underlying defect, but is excluded due to an overly narrow recall scope. I am submitting this complaint in support of Recall Query RQ24-013, which is currently under review to determine whether Honda failed to

Engine shut off due to rod bearing failure

The rod bearing went on this car. I don't understand how there was an open recall but this car was NOT included with the issue. This makes no sense to me. This was a huge cost to my hard working family to fix and Acura was less than helpful esp considering it was an actual recall for our car year. But due to our luck, our car was NOT included. I feel that this needs to be investigated further because more cars were impacted by this recall than were deemed to be included. I reached out previously on this matter to this organization and received NO response.

I purchased the vehicle in 2017. It was certified used by acura dealer but it was practically new; less than a year old with 10,000 miles on it. About a month or so after purchasing I started noticing a an issue when pressing on the gas and the vehicle not responding and a few seconds later it would suddenly jerk trying to catch up to the gear it should be on. Right away I took it to dealership for them to inspect and they said the vehicle needed a "software update" and it should be fine after that. Long story short, it is now 2025 I've taken the vehicle in for a "software update" more times than I can count and I am still living with the same problem. On occasion it gets better and sometimes it gets worse. Especially at higher speeds when the gears seem to go to neutral for a few seconds and then re-engage again on its own which cause jerking/stalling motion.

The contact owns a 2016 Acura MDX. The contact stated that the driver's side rear taillight bulb had burned out. The contact replaced the bulb, but the failure reoccurred. The contact stated that the driver's side rear taillight failure was intermittent but was a persistent failure. The contact had taken the vehicle to an independent mechanic who diagnosed the failure and determined that there was water inside the taillight assembly which caused the bulb to short circuit. The mechanic informed the contact that the taillight assembly needed to be replaced. The vehicle was not repaired. The contact researched online and related the failure to NHTSA Campaign Number: 25V259000 (Exterior Lighting, Interior Lighting); however, the VIN was not included. The manufacturer was not informed of the failure. The failure mileage was approximately 141,000.

My Acura MDX 2016, when stopped in traffic or at a red light will randomly shut down or switch to neutral. It started 2-3 years back. This has happened frequently last few months. Last time i was stuck in the exit of a parking garage blocking the exit. After around 20-30 mins the car decided to start on its own. I took the car directly to a dealer who found no issues with the car. I had the battery replaced recently with a new battery Upon searching the internet, i found this link where each person is describing the same issue [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Vehicle started having issues just a couple of years after purchase (acquired brand new as a Lease which I later purchased when the Lease was up), in the beginning it was mostly at low speeds, but it would occasionally happen at higher speeds as well. You could feel it having hesitation when shifting gears. Took it to the dealer at around the 30K miles due for service (May of 2019). Had the transmission fluid replaced, dealer noted some "debris" was found. The problem quickly showed up again soon after this service, so the vehicle was brought back to the dealer for further checkup a couple of times, the result was always the same, no problem found, and the vehicle was OK to drive. I have lived with this problem ever since and on occasion it got even worse at higher speeds (around 65mph) when the gears seemed to go to neutral for a few seconds and then re-engage again on its own. Knowing that the car had always acted funny and the fact that the dealer never found any issues, I thought it must be more of the same. Finally, a couple of weeks ago (March 25 of 2025) the transmission gave up completely while my wife was driving the car, luckily it was not in a highway, she had enough time to pull to the side of the road but once the car stopped, it would not get into gear again. I have called the dealer for assistance, but they tell me the car is not under warranty anymore and there is no recall pending for this VIN, they could take it in, but the repairs would not be covered by th

I drive a 2016 Acura MDX, with less than 80K mileage. My car has an idle stop feature which was not working and I was having trouble starting my car in the mornings when it was cold. I assumed the battery was getting low, replaced to a new battery and the idle stop began working again momentarily. However, after coming to a stop and the idle stop feature engages, the vehicle was not always automatically restarting. More than once a day it turns off engine as intended with idle stop, but then my car shifts into Neutral and the engine fully dies. I'm left at stop lights or stop signs with a car that is off and will not restart. The last instance I was almost hit by a car when the light turned green and I could not drive forward. I have to shift into park, turn the on/off button, press my foot on the brake and push on/off button 2-3 times to get the car to start back up. All of this on a battery that’s less than a week old. More often then not the idle stop is not working at all. I’m left with a message on my dashboard “auto engine idle stop unavailable.” My VIN was not listed under the Acura SB to “update the PGM-FI software that may affect the idle stop operation and starter under certain conditions.”

Due to a manufacturing defect of the engine crankshaft, the connecting rod bearing prematurely wore and could seize. This is a recall for 2016 MDX V6 engines, my VIN is not included for some reason.

Paint on the roof just suddenly peeled off 2 days ago. There's a Service Bulletin 19-029: [XXX] , but ACURA says the extended warranty is expired and they cannot do anything. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My Acura mdx 2016 has always had oil changes on time . Also only 93 octane gas . Online there are 100’s of people complaining about my issue which there is a recall for same year make and model but my vin is not included. The recall is for rod knock , and this is what I’m experiencing right now out of nowhere. And Acura will not own up to it very upset . This is a very dangerous situation that can cause an accident with my family in the vehicle . Do to engine lock up .

Connecting rod failure causing the need for engine replacement. This connecting rod has been part of a recall campaign by Honda for 2016-2020 MDX models, but this 2016 engine VIN [XXX] is not part of the recall, even though the SAME EXACT issue as the recall is what occurred. Acura is refusing to honor the recall. This happened while on a highway in the California mountains, going uphill, putting my entire family at risk as the vehicle lost power and became inoperable. The dealership confirmed the connecting rod failure, but informed me of Acura's denial on the recall claim. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I have a 2016 Acura MDX with only 120,000 miles on it. Recently I started hearing a knock coming from the engine. I have taken it to three different mechanics, including an Acura dealership mechanic. I was informed by all three to not drive the car due to the fact that it was a rod bearing defect/problem. They all commented that I was lucky that it had not thrown a rod or I could have been injured or possibly had my engine freeze up while driving injuring myself or someone else. After some thorough investigation/research, I have been informed that my make and model has been recalled for the same issue, unfortunately, my Vin number is not included in the recall for whatever reason.

The contact owns a 2016 Acura MDX. The contact stated while driving 20 MPH, there was a loud knock sound coming from the engine compartment, and afterward, the vehicle lost motive power. The contact was able to coast to the shoulder of the roadway, where the vehicle failed to restart. No warning lights were illuminated. The vehicle was towed to the dealer, who diagnosed a failure with the connecting rod bearing in cylinder #3. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 23V751000 (Engine and Engine Cooling); but the VIN was not included. The manufacturer was notified of the failure, and a claim was opened; however, the claim was later denied. The failure mileage was 122,000.

What component or system failed or malfunctioned, and is it available for inspection upon request? The motor's rod bearing spun. It is available for inspection. How was your safety or the safety of others put at risk? The failure could have created enough friction between the bearing sleeve, rod and/or journal bearing to seize the motor and the drivetrain while driving. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes the vehicle was taken to the Acura dealership to be inspected, diagnosed and repaired. There is a recall for the same year, make and model but my vehicle's VIN is not included in the recall. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? The vehicle has only been inspected by the Acura dealership. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? There was a check engine light that produced code P0430 (Catalyst System Efficiency Below Threshold Bank 2) and P0306 (Cylinder 6 Misfire Detected). The vehicle had a loss of power and troubles accelerating under load. The first time the problem was noticed was January 18th, 2025.

My Acura mdx 2016 is well maintained, only 42500 miles,bought brand new from dealer, problem started 6 months ago, accelerator, rpm goes up even on 20 miles driving, and car just stops and gear goes to park mode..dealer inspected, they said transmission needs to be replaced, contacted NCDS, their respond I passed the warranty of 7 years, not covered. Dealer charging 7100 to fix issues.

After starting the engine, when attempting to slowly accelerate, the engine almost dies or hesitates to respond to accelerator. Dangerous situation.

Problem started with Check Engine light coming on, then going off, then coming on again followed by what seemed like all system failure lights getting reported. A clicking/rattling started to be heard in the engine. When driving the vehicle to the dealer to get it inspected the vehicle engine cut out while cruising at 45 MPH. I was able to roll to a stop on the side of the road luckily, it would not start and needed a tow to a more local related dealer (Honda) repair. Honda repair did not move past reading the codes, so I transported the vehicle via a service to the nearest Acura dealer, where they diagnosed the internal rod problem, with the fix being a replacement engine. The vehicle remains at this Acura dealer service.

I was driving down the road & without any warnings my car suddenly loss power. Engine started a really bad knocking sound then stalled out , took to certified mechanic and he told me I need a new engine. Prior to this there were no boarding likes or issues related to the car.

Loud Clicking sound, engine light blinking, car was shaking horribly almost caused an accident.

“Emissions system problem” warning light has lit up on dashboard twice. This was checked and found to be a faulty code both times however, the second time it occurred, it correlated with the sway bars needing to be replaced.

Vehicle engine started making noise . Called Acura customer service . They advised have taken to Acura dealership for examination. Did so ($450.00 tow bill) there is a motor recall on 2016 Acura MDX. The Acura garage advised ( in writing ) that they felt this was the same engine problem ( rod bearing ) as in the 2016 Acura MDX under recall. . Acura corporate advised mine was not listed as recalled .

The contact owns a 2016 Acura MDX. The contact stated that on several occasions while driving at various speeds, the vehicle downshifted inadvertently. The vehicle was towed to a dealer where the failure was not able to be replicated. The contact stated that on one occasion while attempting to place the gear in any gear other than reverse (R) the gear selector indicator displayed the gear selected but the vehicle did not operate as intended. The manufacturer was notified of the failure. The failure mileage was approximately 70,000.

Engine knocking noise, irritable shaking while on road, dangerous driving conditions. Engine Failed and diagnosed at Acura Dealership as failing bearings and connector rod. This issue is under investigation NHTSA Action Number: RQ24013 and I am currently being forced to pay out of pocket for the repair amounting to several thousand dollars. Acura needs to recall these engines NOW and get it fixed. This driving condition is EXTREMELY unsafe, the entire car shakes uncontrollably. This car was bought brand new from dealership by myself. 1 owner. Always serviced at Acura or Honda dealerships.

I have a 2016 Acura MDX with nearly 79,000 miles on it. It died without warning late at night while on the freeway on [XXX], leaving my [XXX] son stranded alone in a dark, remote area for about an hour. Not a safe situation! I had it towed to Shadetree Auto in Layton, Utah. They informed me that the engine had seized. What!? It was well maintained and just had the oil changed a few days previously. They wanted over $11,000 for a used engine. (See Attached Invoice & Report). They couldn't figure out why a well-maintained engine with only 79,000 miles on it would just seize up. Coolant was also not the issue. I couldn't afford it, so it sat for a couple of months until I discovered that there was a Recall on that year for faulty connecting rod bearings that was causing engines to seize. So, I checked into it, but my particular VIN # was not included in the recall. I found a copy of a letter from Acura stating that they were still determining the extent of the problem, nevertheless, they rejected my claim as not included, rather than extending the recall to include my vehicle's documented problem. (See the attached Acura letter dated Feb 7, 2024). I had my car towed to Jody Wilkinson Acura in Salt Lake City for a detailed inspection and second opinion and they confirmed that the engine was seized and that it I had a broken connecting rod on cylinder #1 due to a spun bearing (See photos at the end of attached email). But Acura continued to deny my claim. Jody Wilkinson's quoted m

Rear inner tail light on driver side is not working (34155-TZ5-H03). There is active recall on models between 2014-2019 but when checked my VIN it shows it is not covered. I went through the detail of recall and it can be clearly seen that the damage is same as shown in the recall. I will appreciate if someone can provide how do we know that my VIN was not impacted as there could be subcomponent which could have led to same issues as others from this period. I will appreciate if a prompt action can be taken and my vehicle can be added to the recall list as well. Thanks!

While driving on an interstate highway at 73 mph, under cruise control, at night, as the road started to incline up a hill my vehicle started losing power. The highway is two lanes each way, and I was in the left-hand lane passing a slower vehicle that was in the right-hand lane. There were cars behind me in my lane. When my car started losing power, the check-engine light came on along with some other indicators. I attempted to maintain speed by depressing the accelerator, but the car continued to slow down. It was nighttime when this happened, on a pitch-black highway that had been freshly paved. I was able to finally get behind the car I had been attempting to pass and was then able to get into the emergency lane and stop. My car was making a ticking noise. I turned off the car, opened the hood, but it all looked fine. I looked under the car - there were no fluids running out of the car. I checked the oil, and it was at the full mark on the dipstick - I had changed the oil about 1000 miles prior to this event. When I took the car to a local Acura dealer, they told me that the noise I was hearing was "rod knock", and that it would cost about $8000 to repair by purchasing a short block and having them install it. When I started researching the issue I learned that some 2016 Acura MDXs have a known issue of incorrect rod bearing size, but that my vehicle is excluded because it was evidently manufactured before a certain date. My car has only 125,116 miles on it. It is maintai

Vehicle always smells hot or as if something electric is burning in the engine compartment. Have always had scheduled maintenance and have taken it in on time for all oil changes and maintenance to be performed. Have asked for this to be checked at that time and when the smell has become over powering. Engine lights have popped up and then all lights have shut off two separate times previously to the point where I had to turn off the vehicle. I have taken it to two dealerships and another mechanic to look for the cause. They are not able to determine the cause but recommend I contact Acura as this sounds like a warranty issue.

This occurrence with the vehicle happened in October of 2023 and I no longer own it. The only reason I'm reporting it today is because of the news reports I've been seeing about a possible investigation into the exact issue I experienced. I started to hear a knock from the engine that got progressively worse over the course of a week. I made an appointment to have it looked at, but before I could even make it to that appointment multiple dash lights and warnings started showing up on the meter combi. Engine light was the first to appear followed by the transmission light, then the vehicle went into "limp mode." It wouldn't go over 30mph and eventually just shut itself off; every warning lamp on the dash was on. It was towed to a local Acura dealership where the service tech diagnosed the issue and stated it was a connecting rod bearing that had worn prematurely and there was movement in the piston. I had them check for a recall then and my VIN was not on the list so I proceeded to source a motor and have another shop swap it for much cheaper. That being said, I would very much like to be reimbursed for the costs I incurred. I have multiple documents and at one point had a video that the dealership tech sent me showing the defect. Not sure if they can provide that now or not.

The engine started to make noise, drove it to the Acura Dealership. The engine seized at the repair bay. The technician initially said they just had a recall on these engines then after looking up the ID notified me that the blown engine was not covered under the recall. After several calls to Honda corporate customer service they informed me that they knew it had a faulty engine however it was not under the recall and they didn't have to repair or replace. I paid the dealership to install another engine at my own expense.

Our 2016 MDX starting peeling paint off the roof. Acura said they extended the warranty for this known defect for an 8 year period. Since this problem just happened we are outside the 8 year extension. The internet is full of similar stories of people like us who have the paint peeling after the bogus 8 year extension. Acura said they aren't responsible. This isn't right.

The contact owns a 2016 Acura MDX. The contact stated that while driving on several occasions at various speeds, the vehicle lost power. The vehicle was steered to the side of the road after each failure and restarted. The contact stated that an unknown fault code was displayed occasionally. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 70,000.

Engine blew a rod at 130,000 miles. Replaced engine. Maintained vehicle correctly And changed oil regularly. contacted Acura, but no help. Other vehicles reported similar problems and recalls issued., but not for my particular vehicle.

Driving on [XXX], car began to make a loud noise, began to lose power and smoke was pouring out of the engine. No check engine lights came on. Pulled over immediately and turned off engine, and smoking continued. Car was in a unsafe location and we had to wait an hour with traffic very close for a tow truck. Large quantities of oil leaked out of the engine. Car was towed to Niello Acura in Roseville CA. They diagnosed Catastrophic Engine Failure. Large hole in oil pan and wrist pin found lodged between A/C compressor bracket and engine block. Wrist pin secures the piston to the connecting rod (there is a recall on Acura MDX's for this but my car was not included) Needs new engine. All maintenance was up to date. 78K miles on the engine, had just been serviced at 75K. Purchased at 18K as a Certified Used Vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The car suddenly shut off when i was on the red light wit the idle stop.

The contact owns a 2016 Acura MDX. The contact stated that while driving 40 MPH, there was a knocking sound coming from the engine. The vehicle was driven to the residence. The check engine warning light was illuminated. The vehicle was then towed to a local dealer to be diagnosed. The contact was informed that the rod bearings had failed, and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 86,000.

I am [XXX] and I have owned Honda/Acura since I was 16 yrs old. My last vehicle was a Honda Odyssey minivan with 423K when I donated it, running well to a family that fostered kids! I bought a new 2016 Acura MDX and now it is 8 years old and has 180K on it. I get the oil changed and other normal service maintenance done only at Honda or Acura dealerships. I have never had a car accident and I take care of the maintenance early. All of a sudden, on Friday, [XXX], I had just started driving ( ~20 minutes in the car) and every light started flashing and the car sounded funny and it was hard to drive. I immediately got off the highway and found a repair place (Red's auto repair) right off the exit. They had me shut off the car. Then they checked the oil, which was showing 70%, and I had just had it changed less than 1000 miles earlier, and it had plenty of oil. They told me I could not drive the car! They said "something is wrong with the engine". Currently, LaFontaine Acura has my car. I have a loaner from them. They said it "spun a bearing" in the engine. Apparently there is a recall for this same problem for my year, make and model, but "currently" my VIN number is not included? And, it is the exact same problem bearing from the recall! THIS IS CRAZY! My car has been well taken care of and I would expect it to get at least 350k miles at least before any issues. If the same problem was recalled for other cars, why not mine? It is un-drivable now. I think that Honda has changed

I have had numerous instances of the car not engaging the transmission when driving. This can happen at highway speed; the car will not accelerate and acts like it is in neutral. You must take your foot off the gas pedal for the transmission to re-engage before accelerating. This has been an ongoing problem for a few years, and Acura says there is nothing wrong. This is very dangerous. I know multiple MDX owners who have experienced the same issue. I think there may be a class action lawsuit about it.

I was driving on the interstate going 80 when the car shut off. I coasted to the shoulder and had the car towed to the mechanic shop. The connecting rod broke, going through the engine causing me to need a new engine. When I contacted Acura they said my car wasn’t in the recall even though it’s exactly what was happening to other cars the same year and make as my car.

Failure of connecting rod bearings leading to complete engine failure.

I was driving my 2016 Acura MDX (approximately 87,000 miles) at around 60 mph on the freeway when the engine began making a metallic clanking noise. Shortly after, the check engine light started flashing, and the vehicle lost acceleration, eventually coming to a complete stop. This created a potentially dangerous situation, but I was fortunately able to pull over safely. After the vehicle stopped, the engine would not restart. The mechanic who inspected the vehicle confirmed that the engine has seized. This incident occurred without any prior warning signs and could have resulted in a severe accident. I believe this issue poses a significant safety risk to drivers and passengers. I request an investigation into whether this problem could be due to a manufacturing defect or systemic issue with this model.

I am the owner of a 2016 Acura MDX Advance. While driving, I noticed an unusual knocking sound coming from the engine, despite no warning lights or error messages prior to this incident. Concerned about the noise, I promptly brought the vehicle to an Acura dealership for inspection. The initial diagnosis revealed a camshaft issue, which was replaced. However, upon reassembly, the technician detected a persistent knock that required further investigation. After a week of detailed inspection, the dealership traced the problem to a defect with the rod bearing, an issue that has been part of previous recalls, though my vehicle was not listed. This rod bearing defect caused significant internal damage to the engine, ultimately requiring a complete short-block replacement to restore proper functionality. While the dealership has since resolved the issue, I am deeply concerned about the safety implications of such a defect. Had the rod bearing failed entirely, it could have led to an engine blowout, risking sudden loss of power at highway speeds and potentially endangering my safety.

Car had a failed crankshaft causing a rod bearing issue with the motor. The check engine light came on during use and car was taken to a local repair shop. The independent repair shop determined the issue is associated with recall TSB 24-001, and advised it be transported to a Honda dealership for repair. Honda confirmed that although the 2016 is under this recall this specific VIN is not. Car was repaired at Honda dealership with same exact repair kit and work done to fix the TSB 24-001 recall notice. Reached out to Honda customer service to understand why the car was not repaired under this current recall but was not given any additional information, case #14733117.

My 2016 Acura MDX with 113,000 miles on it suddenly experienced engine failure while driving my son to college in Salisbury, MD. The engine lost all power as I was coming off of the highway onto a side street in Salisbury. Fortunately no other vehicles were around me at the time and I was able to drift into a safe parking area. If it had happened on the highway or in traffic, it could have caused an accident. There were no warning lights on and the vehicle seemed to be running normally right up until it lost power. After having the vehicle towed to an Acura dealership, the mechanic found a broken rod that was likely due to a bad rod bearing. Other 2016 Acura MDX's have been recalled due to a defective rod bearing resulting in engine failure, but my VIN is not covered under the recall. Honda National just confirmed that it will not cover my MDX's repair under the recall. Prior to this, I had done all required maintenance on the vehicle.

The car began making a front end noise and running shoddy and when we took it to the dealer they had to replace bearings/short block at 121k miles. We were told our VIN was outside of the previous recall so it wouldn’t be covered under that. We ended up paying a portion of that very large bill which inconvenienced our family. We were without our own vehicle for many weeks due to back ordered parts for the major repair. This car has always been serviced by Acura at regular intervals.

In July of 2024 my vehicle began to make a knocking sound from the engine. I started a claim through my third party warranty company and brought it to a repair shop. The shop informed me about the recall for my model and year vehicle, but my VIN was not included in the recall. It was determined that the connecting rod bearings failed, and after waiting for 6 weeks the engine was replaced with a used engine from the same year and model vehicle. I drove for about 1900 miles and the engine began knocking again. I returned the to the repair shop and the supplier of the engine provided another used engine. I am terrified that the same problem will occur again and feel the engine can fail at any time.

The engine failed and was unable to be repaired like old Honda and they had no interest in resolving the issue, nor do they offer any replacement with.

Engine started knocking and quit working while driving on the freeway. Was a connected rod bearing failure that was not included under the warranty or recall. Honda paid 75% of repairs but I had to pay $3300 myself.

While waiting to turn left from a busy street onto a highway, the engine seized. The car was unable to be moved from it's location in the center of the busy street with cars approaching quickly from behind and weaving around my stopped vehicle. I had the vehicle towed to Metro Acura in Montclair, CA and they confirmed that the connecting rod bearing had failed causing the engine to seize. They also confirmed that the vehicle is not part of the existing recall. The engine produced some rough noise prior to failing but otherwise did not provide any warning lamps or other messages.

I was driving back yo my home with my family and on freeway Acura MDX engine stopped with clanking metallic sound fortunately I was able to stop safely. This VIN [XXX] should be part of recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)